Continuous and Butt Hinges for Enclosure Doors
Product Specifications
Product Overview
An enclosure door hangs on one of two hinge families, and the choice is made by the door rather than by taste. A continuous hinge, which the trade also calls a piano hinge, runs the full height of the door and carries the load through dozens of knuckles and screws. A butt hinge puts the same door on two leaves and four to eight screws. The continuous part resists a door that sags at the far corner, and it does so because the load is shared, not because the steel is thicker.
The second decision is the knuckle. A single knuckle hinge opens about 180 degrees and the door stops against the frame, which is what a cabinet with a flush front needs. A double knuckle hinge opens to 270 degrees, so a lid can swing back and rest flat against the case. On a road case, a portable instrument or a field terminal that is opened on a bench, that extra 90 degrees is the difference between a lid that stays up on its own and one that has to be held.
The Penn Elcom piano range on this page covers leaf widths from 20 mm to 101 mm. H14001 is the small end: a 20 mm leaf, 348 mm long, punched on 51 mm centres in 1.0 mm steel with a nickel finish, and light enough to screw to a sheet metal cover. P1321P takes the same 51 mm punching on a 27 mm leaf over a 1828 mm length in 1.2 mm nickel plated steel, and P1309P widens that to 37 mm. P1301P is the 51 mm leaf version at 72 in, still on 2 in centres, which is the punching most cabinet frames are already drilled for.
Above that width the parts change character. P1310P and P1300P carry a 44.45 mm and a 50.8 mm leaf in 1.2 mm zinc plated steel over 1.83 m, and P1380 goes to a 40 mm leaf on a 2000 mm length in 1.5 mm steel with 61 mm hole centres. The heavier punching matters on a door that is skinned in 1.5 mm aluminium: the screw pulls into the sheet rather than into the hinge if the centres are too wide.
The double knuckle parts are P81506Z and P81507Z, with a 76.3 mm and a 101 mm leaf on a 1828 mm length in 1.5 mm steel, zinc plated, and P8271Z, which is a double hinge set into a 1 1/16 in offset dish. All three rotate to 270 degrees. P8271Z is the one that replaces a piano hinge on a case where the lid has to lie back without pressing on the rear extrusion, because the hinge is sunk below the surface and the knuckle is protected from impact.
Where the door has to come off, the part is a heavy duty piano hinge with a removable pin. P1361Z, P1362Z and P1363Z carry a 38.1 mm, a 50.8 mm and a 76.2 mm leaf, and the pin is withdrawn from the end so the door lifts away with the hinge still screwed to both sides. That is the format for a panel that is serviced on a bench rather than swung open in place.
Butt hinges are the other half of the page, and they are chosen by leaf size and screw count rather than by the door height. P0519Z is a 2 x 1.5 in four hole leaf in zinc, with P0519S in stainless for a wash down cabinet. P0620 widens the leaf to 2 3/4 x 1 1/2 in with six holes, P1327 goes to 2 x 2 7/8 in on six holes, and P0630Z is the 4 x 4 in leaf with eight staggered holes. The metric sizes, 1522 at 39 x 39 mm and P4440-41C at 41 x 27.2 mm, are four hole leaves for a small access door or a cover plate. 1544 is the heavy duty 3.5 x 3.5 in leaf in zinc.
Two accessories are worth listing with the hinges rather than after them. The hinge stop P0635 is fitted to a P0610 butt hinge or to a piano hinge and holds the door at a fixed angle instead of letting it swing to the frame, and the larger P0640 does the same on a heavier door. On a cabinet that is opened against a wall, a stop is cheaper than a bent hinge and a cracked panel.
Key Specifications
| Parameter | Range on this page | Notes |
|---|---|---|
| Hinge families | Continuous (piano), double knuckle, butt | Single knuckle for flush fronts |
| Leaf width | 20 mm to 101 mm | Continuous types, 1.0 mm to 1.5 mm steel |
| Overall length | 348 mm, 1828 mm, 1830 mm, 2000 mm | Cut to length on a continuous hinge only at a knuckle |
| Hole centres | 51 mm, 61 mm, 76 mm on the continuous parts | Match the frame punching before ordering |
| Material and finish | Steel with zinc, nickel or black finish, plus stainless | Stainless for wash down and marine cabinets |
| Opening angle | About 180 degrees single knuckle, 270 degrees double knuckle | Removable pin parts open while the pin is out |
| Pin | Fixed, or removable on the P1361Z to P1363Z series | A removable pin lets the door lift off |
| Butt hinge leaf sizes | 39 x 39 mm up to 4 x 4 in | Four, six or eight holes per leaf |
| Accessories | Hinge stops P0635 and P0640, strap hinges 1903 to 1908 | Stops hold the door at a fixed angle |
Included Models and Order Codes
Part numbers below are the continuous hinges first and the butt hinges second. Leaf width, length and hole centres decide the door, so a part is only interchangeable with another of the same leaf and the same punching.
| Part Number | Type | Leaf Width | Length | Material and Finish | Hole Centres |
|---|---|---|---|---|---|
| H14001 | Piano, punched | 20 mm | 348 mm | 1.0 mm steel, nickel | 51 mm |
| P1321P | Piano, punched | 27 mm | 1828 mm | 1.2 mm steel, nickel | 51 mm |
| P1309P | Piano, punched | 37 mm | 1828 mm | 1.2 mm steel, nickel | 51 mm |
| P1301P | Piano, punched | 51 mm | 72 in | 1.2 mm steel, nickel | 2 in |
| P1310P | Piano, punched | 44.45 mm | 1.83 m | 1.2 mm steel, zinc | 76 mm |
| P1300P | Piano, punched | 50.8 mm | 1.83 m | 1.2 mm steel, zinc | 2 in |
| P1380 | Piano, punched | 40 mm | 2000 mm | 1.5 mm steel, zinc | 61 mm |
| P1361Z | Heavy duty, removable pin | 38.1 mm | Per order | Steel, zinc | Per drawing |
| P1362Z | Heavy duty, removable pin | 50.8 mm | Per order | Steel, zinc | Per drawing |
| P1363Z | Heavy duty, removable pin | 76.2 mm | Per order | Steel, zinc | Per drawing |
| P81506Z | Double knuckle, 270 degrees | 76.3 mm | 1828 mm | 1.5 mm steel, zinc | Per drawing |
| P81507Z | Double knuckle, 270 degrees | 101 mm | 1828 mm | 1.5 mm steel, zinc | Per drawing |
| P8271Z | Double hinge in offset dish | 1 1/16 in dish | Per order | Steel, zinc | Per drawing |
| P0519Z | Butt, four hole | 2 x 1.5 in | Leaf length 1.5 in | Steel, zinc | Four holes |
| P0519S | Butt, four hole | 2 x 1.5 in | Leaf length 1.5 in | Stainless | Four holes |
| P0620 | Butt, six hole | 2 3/4 x 1 1/2 in | Leaf length 1.5 in | Steel, zinc | Six holes |
| P1327 | Butt, six hole | 2 x 2 7/8 in | Leaf length 2 7/8 in | Steel, zinc | Six holes |
| P0630Z | Butt, eight hole | 4 x 4 in | Leaf length 4 in | Steel, zinc | Eight staggered |
| 1544 | Butt, heavy duty | 3.5 x 3.5 in | Leaf length 3.5 in | Steel, zinc | Four holes |
| 1522 | Butt, four hole | 39 x 39 mm | 39 mm | Steel, zinc | Four holes |
| P4440-41C | Butt, four hole | 41 x 27.2 mm | 27.2 mm | Steel, zinc | Four holes |
| P4440-41K | Butt, four hole | 41 x 27.2 mm | 27.2 mm | Steel, black | Four holes |
| 1903 / 1904 / 1906 | Strap hinge | Small, medium, large | Per part | Steel, zinc | Countersunk |
| P0635 | Hinge stop | For P0610 and piano hinges | Per part | Steel, nickel | Fitted to the leaf |
| P0640 | Hinge stop, large | For heavier doors | Per part | Steel, zinc | Fitted to the leaf |
Key Features
Load spread along the door edge – A continuous hinge carries the door through every knuckle on the leaf, which is why a tall door stops sagging at the corner away from the handle.
Punching stated with the part – 51 mm, 61 mm and 76 mm centres are listed per part, so the door is drilled to the hinge rather than the hinge being redrilled to the door.
Double knuckle to 270 degrees – P81506Z and P81507Z let a lid lie back flat against the case, and the offset dish of P8271Z keeps the knuckle clear of impact.
Removable pin variants – P1361Z to P1363Z release the door for bench service without unscrewing either leaf.
Butt hinges by leaf and hole count – Four, six and eight hole leaves from 39 x 39 mm to 4 x 4 in, in zinc, black and stainless.
Hinge stops listed as parts – P0635 and P0640 hold the door at an angle, which protects a cabinet that opens against a wall.
Material matched to the wash down – Stainless butt hinges and nickel plated piano hinges for cabinets that see water, and zinc for a dry plant.
Applications
These hinges go on cabinet doors, lids, access panels and rack fronts where the door has to swing clear, stay put or come off for service.
Test and instrument cabinets – A 44 to 51 mm leaf piano hinge on the full door height, with a hinge stop so the door does not swing into the bench.
Portable and road cases – Double knuckle P81506Z or P8271Z so the lid lies back at 270 degrees and the case stands stable while it is loaded.
Wash down and outdoor enclosures – Stainless butt hinges and nickel plated piano hinges, with the pin and the screws in the same alloy as the leaf.
Access and inspection panels – Small butt leaves of 39 x 39 mm or 41 x 27.2 mm, four holes each, on a cover that is opened a few times a year.
The hinge choice is made against the door mass, the leaf width that the frame can take and whether the door has to lift off in the field, and the SUPERB PCB enclosure drawing usually fixes all three before the parts list is released. On the SUPERB PCBA side the hinge arrives as loose hardware and is fitted after the panel is painted, so the finish on the knuckle is not damaged in the paint booth.
Sourcing and Cross-Reference
Hinges are ordered against the door, not against the catalogue, so a quotation needs four numbers: leaf width, overall length, hole centres and the screw size. A part with the right leaf and the wrong punching is a part that has to be drilled again, and a second set of holes in a 1.5 mm door is how a corner starts to tear.
On a continuous hinge the length can be cut only at a knuckle, so a door of 1.4 m takes a 1828 mm part cut back to the nearest knuckle rather than a part ordered to the millimetre. The cut end has to be dressed and the pin re-set, which is a bench job and not a field job.
Where a part is discontinued or the leaf width is no longer offered, the substitute is chosen on leaf width, punching and opening angle together. A 44.45 mm leaf will take the screws of a 50.8 mm leaf in most frames, but the door will bind if the knuckle line moves. We check the drawing before we quote the alternative.
SUPERB Assembly sets every lid on its hinge before the paint is touched up, opens and closes it twenty times and checks that the pin does not walk, because a piano hinge that is 2 mm short of the frame binds at one end and pulls the screws out of the sheet.
Q: Can you supply a 1.8 m piano hinge with 51 mm hole centres and a removable pin, and confirm the leaf width against our 1.5 mm door?
A: Send the door width and height, the door material and thickness, the leaf width your frame allows and whether the door has to be lifted off. The SUPERB Tech desk quotes the hinge with its hole centres, so the punching in the door matches the hinge you receive.
Why Buy Hinges Through SUPERB
- Part numbers, not categories: Each hinge is quoted by its maker part number with leaf, length, punching and finish, so the door is drilled once.
- Leaf and punching checked against the drawing: The frame punching is confirmed before the order is placed, which is the failure a catalogue photograph cannot show.
- Stainless and plated options side by side: The same leaf in zinc, nickel, black and stainless, so a wash down cabinet does not need a second supplier.
- Accessories in the same shipment: Hinge stops, strap hinges and matching screws are listed with the hinges rather than sourced later.
- Small quantities accepted: A service panel that needs four hinges is quoted at four hinges, not at a box of fifty.
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Draw Latches and Toggle Latches for Enclosure Doors, Enclosure Handles and Corner Guards for Portable Units, Breather Vents and Pressure Equalization Plugs for Sealed Cases, Threaded Inserts and Standoff Nuts for Plastic Enclosures, Eyelets and Rivets for Panel and Board Fixing, Obsolete Part Cross Reference Hub.