Threaded Inserts and Standoff Nuts for Plastic Enclosures
Product Specifications
Product Overview
A screw thread cut straight into a thermoplastic boss has a short life. The first assembly feels fine, the third is tight, and by the fifth the thread has cold flowed and the screw turns without biting. The answer is a metal insert: a brass or steel part that is set into the plastic, either by heat or by ultrasonic energy, so the thread is in metal and the plastic only has to hold the insert. The same case has a metal chassis or bracket behind it, and that side uses a self-clinching nut instead.
The heat set inserts on this page are brass, CuZn39Pb3, with a knurled body and two or three knurl bands. M2 is 3.2 mm outside diameter in a 3.0 mm hole with a 3.0 mm length and a recommended 6.4 mm boss. M2.5 is 3.6 mm in a 3.4 mm hole, 4.0 mm long, on a 7.2 mm boss. M3 is 4.6 mm in a 4.4 mm hole, available in 4.0 mm and 5.7 mm lengths, on a 9.2 mm boss. M4 is 5.6 mm in a 5.4 mm hole, 5.7 mm long, on an 11.2 mm boss. M5 is 6.9 mm in a 6.7 mm hole, 5.8 mm long, on a 13.8 mm boss. M6 is 8.2 mm in an 8.0 mm hole, 9.5 mm long, on a 16.4 mm boss.
The boss diameter is the figure that decides whether the case survives. A 4.6 mm insert in a 4.4 mm hole needs at least 2.3 mm of wall on each side to carry the hoop stress of the press fit, which is where the 9.2 mm recommended boss comes from. A boss that is 6 mm on an M3 insert has 0.7 mm of wall, and that is the boss that splits on the first drive or the first drop. Where the boss cannot be enlarged, the next size down is the answer, not a shorter insert.
The installation temperature is the second figure. These inserts are set with a heated tip at 200 to 250 C, which melts the plastic around the knurl and lets it flow back into the bands as it cools. Too cold and the insert sits proud and turns. Too hot and the plastic degrades and the insert sinks. The length matters here too: a 5.7 mm insert needs a boss deep enough to take it plus 1 mm of plastic below, or the tip of the insert breaks through the far wall.
The metal side of the same assembly uses a self-clinching nut. The PEM CLS series covers M2 and M2.5 and M3 in a 4.22 mm hole with a 6.35 mm head and a 1.5 mm shank, M3.5 in a 4.75 mm hole, M4 in a 5.41 mm hole, M5 in a 6.35 mm hole and M6 in an 8.75 mm hole with a 4.08 mm shank. The minimum sheet is 1.0 mm for M2 to M3 and 1.2 mm for M6, and the minimum hole centre to edge runs from 4.8 mm to 8.6 mm. Those are the numbers that decide whether a bracket can take the nut at all.
The practical rule on a plastic case is to decide the screw before the mould. An M3 screw needs a 9.2 mm boss, and a 9.2 mm boss needs 2.5 mm of wall and a corner radius. A case that was laid out for a self-tapping screw has neither, and the insert is then either too small for the load or too large for the boss. Getting the insert into the first drawing is much cheaper than re-cutting the tool.
Key Specifications
| Parameter | Value | Applies to |
|---|---|---|
| Insert material | Brass CuZn39Pb3 | Heat set inserts |
| Thread range | M2 to M6 | Heat set inserts |
| Outside diameter | 3.2 mm to 8.2 mm | Heat set inserts |
| Insert length | 3.0 mm to 9.5 mm | Heat set inserts |
| Hole in the plastic | 3.0 mm to 8.0 mm | Heat set inserts |
| Recommended boss | 6.4 mm to 16.4 mm | Heat set inserts |
| Knurl bands | 2 or 3 | Heat set inserts |
| Installation temperature | 200 to 250 C with a heated tip | Heat set inserts |
| Nut material | Carbon steel, stainless steel | CLS series |
| Nut thread range | M2 to M6 | CLS series |
| Nut hole in sheet | 4.22 mm to 8.75 mm | CLS series |
| Minimum sheet for the nut | 1.0 mm to 1.2 mm | CLS series |
| Minimum hole centre to edge | 4.8 mm to 8.6 mm | CLS series |
| Sheet hardness for clinching | HRB 70 / HB 125 or less | CLS series |
Included Models and Order Codes
The rows below are the brass heat set inserts we quote most often. Hole size, length and boss diameter are given per thread because the boss, not the thread, is what fails first in a plastic case.
| Thread | Outside Diameter | Length | Hole in Plastic | Recommended Boss | Knurl Bands |
|---|---|---|---|---|---|
| M2 | 3.2 mm | 3.0 mm | 3.0 mm | 6.4 mm | 2 |
| M2.5 | 3.6 mm | 4.0 mm | 3.4 mm | 7.2 mm | 2 |
| M3 | 4.6 mm | 4.0 mm | 4.4 mm | 9.2 mm | 3 |
| M3 long | 4.6 mm | 5.7 mm | 4.4 mm | 9.2 mm | 3 |
| M4 | 5.6 mm | 5.7 mm | 5.4 mm | 11.2 mm | 3 |
| M5 | 6.9 mm | 5.8 mm | 6.7 mm | 13.8 mm | 3 |
| M6 | 8.2 mm | 9.5 mm | 8.0 mm | 16.4 mm | 3 |
Self-Clinching Nuts for the Metal Side
Where the plastic case is fixed to a steel or aluminium bracket, the thread on that side is a self-clinching nut. Hole size, sheet thickness and edge distance are given per thread, because a 6 mm hole 4 mm from a bend tears the bracket.
| Part Number | Thread | Hole in Sheet | Min Sheet | Head E | Shank T | Min Centre to Edge |
|---|---|---|---|---|---|---|
| CLS-M2-1 | M2 | 4.22 mm | 1.0 mm | 6.35 mm | 1.5 mm | 4.8 mm |
| CLS-M2.5-1 | M2.5 | 4.22 mm | 1.0 mm | 6.35 mm | 1.5 mm | 4.8 mm |
| CLS-M3-1 | M3 | 4.22 mm | 1.0 mm | 6.35 mm | 1.5 mm | 4.8 mm |
| CLS-M3-2 | M3 | 4.22 mm | 1.4 mm | 6.35 mm | 1.5 mm | 4.8 mm |
| CLS-M3.5-1 | M3.5 | 4.75 mm | 1.0 mm | 7.11 mm | 1.5 mm | 5.6 mm |
| CLS-M4-1 | M4 | 5.41 mm | 1.0 mm | 7.87 mm | 2.0 mm | 6.9 mm |
| CLS-M5-1 | M5 | 6.35 mm | 1.0 mm | 8.64 mm | 2.0 mm | 7.1 mm |
| CLS-M6-0 | M6 | 8.75 mm | 1.2 mm | 11.18 mm | 4.08 mm | 8.6 mm |
Key Features
Boss diameter stated per thread – M3 needs a 9.2 mm boss and M6 a 16.4 mm boss, which is the figure that is missing when a case splits on the first drive.
Two lengths for M3 – The 4.0 mm and 5.7 mm M3 inserts cover a thin lid and a deep corner post with the same thread.
Knurl bands for the press fit – Two or three bands hold the insert against pull-out and against turning, which is what a plain knurl does not do.
Installation temperature given – 200 to 250 C with a heated tip is stated, because a cold insert sits proud and a hot one sinks.
Metal side covered – Self-clinching nuts from M2 to M6 are on the same page, with hole size and edge distance for the bracket behind the case.
Ratings from the maker data – Every dimension is taken from the part data, so the mould drawing and the insert order use the same numbers.
Applications
These parts are used wherever a plastic housing has to be opened more than once, or where a metal bracket has to take a thread in thin sheet.
Handheld instrument cases – An M3 heat set insert in a 9.2 mm boss gives a lid screw that survives repeated battery changes, where a self-tapping screw would strip by the fifth cycle.
Sealed plastic enclosures – An M4 insert 5.7 mm long in a deep corner post carries the lid load without breaking through the outer wall.
Metal brackets and chassis – A CLS-M3-1 nut in a 4.22 mm hole in 1.2 mm steel gives the plastic case a metal thread to bolt into, with 4.8 mm of edge distance.
An insert is placed before the enclosure is moulded or punched, so the boss diameter is checked against the SUPERB PCB keep out and the wall thickness on the first shot. On the SUPERB PCBA route the inserts are set before the board is fixed down, because a boss that is drilled out after the board is in place is a boss that fills the case with swarf.
Sourcing and Cross-Reference
An insert is bought by screw and by boss. The screw size is on the drawing and the boss usually is not, which is why a case arrives with a 6 mm boss for an M3 insert and splits. When a part is replaced, the hole in the plastic, the wall around it and the plastic grade are the three figures to send, because the same insert behaves differently in ABS and in glass filled nylon.
The second point is the plastic. A heat set insert relies on the plastic melting and flowing back around the knurl, so a glass filled grade needs more heat and a higher pull-out force is not guaranteed. A thin wall cools fast and the insert can sit loose. Where the wall cannot be thickened, the insert gets longer rather than wider, because length adds pull-out resistance without adding hoop stress to the boss.
The third point is the metal side. The bracket behind the case takes a self-clinching nut, and that nut needs a hole size within 0.08 mm and a minimum edge distance of 4.8 mm for M3. A nut set too close to a bend distorts the bracket and the screw no longer goes in square. We quote the insert and the nut together, because the two sides of the same fixing are usually decided at the same time.
SUPERB Assembly sets the first insert at the quoted temperature and drives a screw in and out ten times, because an insert that turns in its boss after five cycles is a lid that will not come off again.
Q: Can you supply M3 brass heat set inserts for a 4.4 mm hole with a 9.2 mm boss, and the matching self-clinching nuts for the 1.2 mm steel bracket behind the case?
A: Send the screw size, the wall thickness and the plastic. The SUPERB Tech desk quotes the insert with its hole diameter, length and recommended boss diameter, because an M3 insert needs a 4.4 mm hole and a 9.2 mm boss, and a 6 mm boss splits on the first drive.
Why Buy Threaded Inserts and Standoff Nuts Through SUPERB
- Boss checked with the thread: Every insert is quoted with its recommended boss, because the boss is the part that splits when the insert is one size too large.
- Length matched to wall: Two M3 lengths and the full M2 to M6 range are on one page, so a thin lid and a deep post are not forced onto the same insert.
- Installation data on the quote: The 200 to 250 C setting range is stated, because a cold insert turns and a hot one sinks.
- Both sides of the fixing: Heat set inserts for the plastic and self-clinching nuts for the metal are quoted together, with hole size and edge distance.
- Cycled at assembly: The first insert is set and the screw is driven ten times, because an insert that turns after five cycles is a lid that will not come off.
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Standoffs Spacers and Mounting Hardware for Board Stacks, Enclosure Handles and Corner Guards for Portable Units, Rubber Bumpers and Feet for Enclosure Support, Nylon Grommets and Hole Plugs for Panel Openings, EMI Shielding Cans and Contact Gaskets for RF Boards, Obsolete Part Cross Reference Hub.