Contact Us
  • Home
  • COMPONENTS
  • Anti Condensation Heaters for Electrical Enclosures

Anti Condensation Heaters for Electrical Enclosures

Small PTC heaters that hold a cabinet a few degrees above the dew point, which is what stops condensation on terminals. Radiant versions from 10 W to 30 W warm a single cold spot, convection versions from 15 W to 150 W warm the whole box. Fan heaters from 200 W to 800 W spread the heat when the cabinet is large or the ambient swings fast. Mounting, inrush current and surface temperature are listed per part, since they decide the fuse and the clearance.
quote now

Product Specifications

Product Overview

Condensation does not need rain. A cabinet that is warm and humid inside, and cold on its steel skin, will form water on the inside of the door and on the coldest terminals in the box. The usual sequence is a warm day, a cool night, and a control panel that trips at four in the morning on a fault that cannot be found at noon. The water is not a leak, it is the dew point crossing, and no gasket stops it.

The remedy is to keep the inside surface above the dew point, and that takes far less power than most people expect. Ten to thirty watts in a small enclosure, or fifteen to one hundred and fifty watts in a medium one, is normally enough to lift the internal air a few degrees and to keep the steel above the condensation point. A PTC element is the right source for this job because its resistance rises as it heats, so the output falls back instead of running away, and the heater can be left on continuously without a thermostat.

Sizing is a heat balance, not a guess. The cabinet loses heat through its surface at roughly 5.5 W per square metre per kelvin for painted steel, so a one square metre cabinet in a room 15 K colder than the target loses about 80 W. The heater only has to replace enough of that loss to hold the surface above the dew point, which is why a 30 W heater is often correct in a 600 x 400 mm box and an 800 W fan heater belongs in a large floor standing cabinet that is opened often.

Key Specifications

ParameterValueNote
Heating capacity10 W to 800 W across the three families15 to 150 W on the PTC convection body
Supply120 to 240 V AC or DC on the convection heater, 230 V AC on the radiant heaterother voltages on request, output drops about 10 percent below 140 V
ElementPTC resistor, self regulatingthe output falls as the surface warms, so no thermostat is needed for frost protection
Protection typeIP20 on the convection heater, IP54 on the radiant heaterthe heater is inside the cabinet, the IP figure is about dust and touch
Maximum surface temperature95 C at 10 W, 115 C at 20 W, 140 C at 30 Wradiant heater, keep cables 50 mm clear
Inrush current1.5 A at 15 W, 3 A at 30 W, 9 A at 150 Wdecides the MCB curve, a C curve is the usual choice
Operating temperature-45 to +70 Cstorage -45 to +70 C
Mountingclip for 35 mm DIN rail, screw fixing as an accessoryinstallation with the airflow vertical and the connection at the bottom
Connection3 pressure clamps for 0.5 to 2.5 mm2300 mm cable on the radiant heater
Airflow30 CFM, about 50 m3/h, on the fan heaterthe fan is what makes 800 W usable in a large box
Pre-fuse6 A at 200 W, 10 A from 400 W to 800 Wthe maker table gives a pre-fuse per rating
Duty cycle100 percent, continuous operationPTC bodies are built to stay energised
Width70 mm on the convection heater, 29.5 mm on the 10 W radiant heaternarrow bodies fit beside terminals on the same rail

Included Models and Order Codes

The list runs from the smallest radiant heater to the largest fan heater, because a panel line usually needs two sizes rather than one. STEGO part numbers in the 1400x series carry the wattage in the last two digits: 14000 is 15 W, 14001 is 30 W, and the body length grows from 110 mm to 265 mm as the rating rises. The Pfannenberg PRH mini series is quoted with a seven digit article number and a 300 mm cable, and the PFH fan heaters use one article number per voltage, so the 230 V and 115 V versions of the same rating are two different numbers.

Part numberTypeHeating capacitySupplyInrush currentNote
14000.0-00STEGO HG 140 convection15 W120 to 240 V AC / DC1.5 A110 x 70 x 60 mm, 300 g, 35 mm rail clip
14001.0-00STEGO HG 140 convection30 W120 to 240 V AC / DC3 Asame body as the 15 W part
14003.0-00STEGO HG 140 convection45 W120 to 240 V AC / DC3.5 Asame body, higher element rating
14005.0-00STEGO HG 140 convection60 W120 to 240 V AC / DC2.5 A185 x 70 x 60 mm, 400 g
14006.0-00STEGO HG 140 convection75 W120 to 240 V AC / DC4 A185 mm body, 500 g
14007.0-00STEGO HG 140 convection100 W120 to 240 V AC / DC4.5 A185 mm body, 500 g
14008.0-00STEGO HG 140 convection150 W120 to 240 V AC / DC9 A265 mm body, 700 g
17000105317Pfannenberg PRH 010-M radiant10 W230 V AC 50/60 Hz1.0 A29.5 x 50 mm, 95 C surface, IP54, 300 mm cable
17000205317Pfannenberg PRH 020-M radiant20 W230 V AC 50/60 Hz1.1 A115 C surface, 120 g
17000305317Pfannenberg PRH 030-M radiant30 W230 V AC 50/60 Hz1.2 A140 C surface, 120 g
17020610030Pfannenberg PFH 200 fan heater200 W230 V AC9 A30 CFM, pre-fuse 6 A
17040610030Pfannenberg PFH 400 fan heater400 W230 V AC15 A30 CFM, pre-fuse 10 A
17065610030Pfannenberg PFH 650 fan heater650 W230 V AC20 A30 CFM, pre-fuse 10 A
17080610030Pfannenberg PFH 800 fan heater800 W230 V AC31 A30 CFM, pre-fuse 10 A
17020615030Pfannenberg PFH 200 fan heater200 W115 V AC9 Athe 115 V version of the same body
17080615030Pfannenberg PFH 800 fan heater800 W115 V AC31 A115 V version, pre-fuse 10 A

How Much Heat a Cabinet Actually Needs

The heater does not have to warm the cabinet to room temperature, it has to keep the coldest internal surface above the dew point. That is a much smaller number, and it is the reason a 30 W part is often right where a 200 W part looks safer.

CabinetHeat loss at 15 K differenceHeater that usually fits
600 x 400 x 250 mm, painted steelabout 33 W30 W convection heater, or a 20 W radiant part on a small box
800 x 600 x 300 mm, painted steelabout 65 W60 W or 75 W convection heater
1200 x 800 x 400 mm, painted steelabout 125 W150 W convection heater, or a 200 W fan heater if the door is opened often
2000 x 800 x 600 mm, floor standingabout 210 W400 W fan heater, because the air has to move to reach the top of the cabinet
Cabinet in a washdown area, opened dailyloss plus a full air exchange each openingfan heater with a thermostat, the opening is the load, not the steel

Key Features

PTC element, no thermostat needed – the resistance rises with temperature, so the heater settles at its output instead of cycling, which is what makes continuous operation safe.

Surface temperature on the row – 95, 115 and 140 C are listed per radiant part, because cable routing next to the heater is decided by that figure.

Inrush current published – 1.5 A to 31 A across the range, which is the number that decides the breaker curve and stops a nuisance trip on a shared circuit.

Three forms for three jobs – radiant for a cold spot, convection for a whole small cabinet, fan for a large one, with the airflow figure given for the fan version.

Rail mounting as standard – a 35 mm clip is the default and screw fixing is an accessory, so the heater lands on the rail with the terminals it protects.

Voltage bands stated – 120 to 240 V AC or DC on the convection body covers most panels with one part number, and 115 V versions are listed separately.

Applications

Anti condensation heaters are fitted for three situations, and the choice of form follows from which one applies.

Outdoor cabinets and roadside enclosures – the steel skin drops below the dew point every night, so a convection heater on a rail holds the internal surface warm enough that the water never forms on the terminals.

Washdown and food processing areas – daily cleaning puts moisture into the air around the cabinet, and a fan heater with a thermostat dries the box after each shift instead of letting the water settle in the bottom.

Cold stores and unheated warehouses – the cabinet is colder than the air that enters when the door opens, so a radiant heater aimed at the terminal block keeps the one surface that matters above the condensation point.

The cabinet heater sits on the same rail as the control board, so the SUPERB PCBA and the SUPERB PCB are checked against the same 24 V and 230 V separation in the panel.

Sourcing and Cross-Reference

A heater order is usually a rating and a voltage, and the two are easy to separate by accident. The STEGO 1400x body covers 120 to 240 V AC or DC in one part, but the Pfannenberg PFH family has one article number per voltage, so the 115 V and 230 V versions of the same wattage are different numbers. Reading the article number rather than the description is the safe habit here.

The second point is the circuit. A 150 W PTC heater draws 9 A at switch on, and an 800 W fan heater draws 31 A for a fraction of a second, which is enough to trip a B curve breaker shared with other small loads. The pre-fuse and inrush figures on this page come from the maker tables and are there to be used before the panel is wired, not after the first nuisance trip.

Where a rating is short, the alternative is usually the next size up with a thermostat, a second smaller heater on the other side of the cabinet, or a fan heater instead of a convection body when the cabinet is tall. See lead time and availability for a specific part and BOM shortage recovery when a panel is waiting on one heater to ship.

The SUPERB Assembly team keeps the heater circuit on its own breaker rather than sharing the control supply, because an inrush of 9 A on a shared rail is a nuisance trip waiting to happen.

Q: Can you confirm the heater rating and the inrush current for a cabinet of this size, and whether a thermostat is needed?

A: Yes. Send the cabinet dimensions, the lowest ambient, the supply voltage and whether the door is opened daily, and the SUPERB Tech team returns the rating and the form that fit.

Why Panel Builders Buy Enclosure Heaters From SUPERB

  1. Rating, voltage and inrush together: the three numbers that decide the circuit are on one row, which is what an electrician needs before the rail is drilled.
  2. Three forms on one page: radiant, convection and fan versions are listed with their airflow and surface temperature, so the form is chosen from the cabinet, not from stock.
  3. Continuous duty stated: the PTC bodies are rated for 100 percent duty, which removes the question of whether a timer or a thermostat is mandatory.
  4. Small and large parts side by side: a 10 W radiant part and an 800 W fan heater are on the same list, because a panel line usually needs both for different cabinets.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Enclosure Panel Heaters and Thermostats for Cold Cabinets, Enclosure Hygrostats and Humidity Controllers, Enclosure Heat Exchangers for Dusty and Sealed Sites, Enclosure Air Conditioners for Sealed Cabinet Cooling, Filter Fan Units and Exhaust Filters for Enclosure Cooling.