STM32G474CEU6
Product Specifications
STM32G474CEU6 — ARM Cortex-M4F Microcontroller by STMicroelectronics
The STM32G474CEU6 is an STMicroelectronics ARM Cortex-M4F MCU in UFQFPN-48(7x7) for Embedded control and general-purpose MCU applications. Supplied by SUPERB Automation.
Part Number Decoded — Field by Field
| Field | Value | Meaning |
|---|---|---|
| STM32G474CEU6 | Full Part Number | STMicroelectronics ARM Cortex-M4F Microcontroller |
| STM32 | Product Family | STMicroelectronics 32-bit ARM-based MCU |
| G4 | Series | ARM Cortex-M4F based MCU — G4 series |
Quick Specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Part Number | STM32G474CEU6 |
| Core | ARM Cortex-M4F |
| Package | UFQFPN-48(7x7) |
| Temperature Range | −40°C to +85°C |
| Supply Voltage | 1.8V–3.6V |
Product Overview
The STM32G474CEU6 is an STMicroelectronics ARM Cortex-M4F microcontroller in UFQFPN-48(7x7) package. Part of ST's extensive STM32 portfolio, it delivers a high-performance processing platform with integrated Flash, SRAM, and a rich set of communication peripherals for Embedded control and general-purpose MCU applications. Supplied by SUPERB Automation with full traceability and competitive lead times.
Key Features & Benefits
ARM Cortex-M4F Core — Efficient Processing for Embedded Control
The ARM Cortex-M4F core provides deterministic real-time performance with hardware multiply/divide and optional FPU, executing control loops, communication stacks, and sensor fusion algorithms efficiently in resource-constrained embedded environments.
Rich Peripheral Set — GPIO, Timers, ADC, Communication Interfaces
Features a comprehensive set of on-chip peripherals including multi-channel DMA, 12/16-bit ADCs, advanced PWM timers for motor control, and multiple USART/SPI/I²C interfaces for sensor and communication module connectivity.
ST Ecosystem — CubeMX, HAL, LL, Middleware
Fully supported by ST's STM32Cube ecosystem including CubeMX graphical configuration, HAL/LL driver libraries, FreeRTOS integration, and extensive middleware stacks (USB, TCP/IP, FATFS, graphics) — accelerating firmware development and reducing time-to-market.
Target Applications
Embedded Control & IoT Systems
Functions as the main processing unit in embedded control systems, IoT endpoints, sensor hubs, motor controllers, and human-machine interfaces — leveraging the Cortex-M architecture for efficient, low-power operation.
Industrial Automation & Motor Control
Powers industrial motor drives, PLCs, sensor transmitters, and factory automation equipment — taking advantage of advanced PWM timers, high-speed ADCs, and CAN/RS-485 communication for distributed control architectures.
Consumer & Portable Electronics
Integrates into consumer devices, wearables, smart home products, and portable instruments — benefiting from the STM32 family's low-power modes, small packages, and extensive third-party firmware ecosystem.
Frequently Asked Questions
Is the STM32G474CEU6 supported by STM32CubeIDE?
Yes, the STM32G474CEU6 is fully supported in STM32CubeIDE with graphical pinout configuration, clock tree setup, and automatic peripheral initialization code generation — enabling rapid prototyping and production firmware development.
What firmware/RTOS options are available?
The STM32 family is supported by FreeRTOS, Zephyr, NuttX, ChibiOS, and bare-metal HAL programming. For drone applications, Betaflight, iNav, ArduPilot, and PX4 all have STM32 HAL targets.
What is the minimum order quantity (MOQ)?
Contact SUPERB Automation for a tailored quote. We support quantities from prototype tray to full production volumes.
Request a Quote
SUPERB Automation supplies genuine STMicroelectronics STM32G474CEU6 MCUs with full traceability and batch-level QA documentation. Whether you need a single tray for prototype builds or pallet-level volumes for production, we source through verified channels with competitive lead times. Contact us with your target quantity and delivery date — we'll respond with a detailed quotation within 24 hours.
STM32G474CEU6: 512 Kbytes in a 7 mm square QFN
The U in this order code is the UFQFPN body, 7 mm by 7 mm with a 0.5 mm pitch and an exposed pad, and the E is the 512 Kbyte flash density. Forty eight pins, 512 Kbytes and a Cortex-M4F at 170 MHz in a package that occupies less board area than the LQFP48 that carries the same die.
The reason to take the QFN is usually mechanical: a module that has to fit inside a 25 mm housing, a board that is potted, or a product where the height above the board matters. The reason not to take it is rework and inspection, and that trade is the subject of this page. Figures come from DS12288 Rev 6.
The compact body in figures
| Package | UFQFPN48, 7 mm by 7 mm, 0.5 mm pitch, exposed pad |
| Core | Cortex-M4F at up to 170 MHz, 213 DMIPS |
| Flash | 512 Kbytes with ECC in two banks read-while-write |
| RAM | 128 Kbytes total, 32 Kbytes of it CCM SRAM |
| I/O | Up to 40 fast lines on this body |
| ADC | Five 12-bit converters at 0.25 microsecond, 16-bit by oversampling |
| Analog | Seven DAC channels, seven comparators, six op amps with PGA |
| Timers | HRTIM at 184 ps, three advanced motor control timers, 17 in total |
| Fieldbus | Three FDCAN, USART, LPUART, SPI, I2C and USB full speed |
| Supply | 1.71 V to 3.6 V |
| Endurance | 10 kcycles, 30 years retention at 85 degrees C after 1 kcycle |
| Temperature | Minus 40 to plus 85 degrees C, 105 degree junction |
The exposed pad is part of the circuit
A QFN without a via field under the pad is a part running on the copper of its own leads alone. The pad is the main thermal path, and at 170 MHz with five converters active the dissipation is high enough that the difference between a stitched pad and a bare one shows up as a junction temperature 20 to 30 degrees apart. The stencil also has to be adjusted: a single full aperture on the pad lifts the body on a solder blob, and the usual answer is a grid of 60 to 70 per cent coverage with the paste split into windows.
Our tooling and stencil control page covers the aperture rules we apply to QFN bodies, including the window pattern for this package size. Inspection is the other half: the joints sit under the body, so an optical check sees only the fillet at the edge, and an X-ray turn is what confirms the pad wetting on a first article.
Why 512 Kbytes in 48 pins
The combination looks unbalanced until the application is known. A compact servo module with a fieldbus stack, a motion profile table and a bootloader uses the flash, and it does not need 100 pins because the power stage is driven through the HRTIM on a fixed set of lines and the feedback comes in on a multiplexed converter. The 512 Kbyte member also brings the two bank read-while-write arrangement, which matters on a sealed module that is updated over the bus in the field.
Where the pin count does bite is on parallel interfaces: this body has no external memory controller, so a data log needs the quad SPI route or an external device on the serial bus. The MCU cross reference page sets out which bodies in the family keep the same pinout when the line count grows.
Practical notes for the build
MSL rating and floor life decide how the reel is handled. A QFN body at this pitch is normally level 3, which allows 168 hours of floor life after the bag is opened, and a line that cannot consume a reel inside that window has to bake it or store it dry. That is a planning item, not a production surprise, and it belongs on the traveller next to the reel count.
Rework is possible with hot air and a preheat from below, and it is slower than a leaded package because the pad has to be cleaned and re-pasted before the new part goes down. For a prototype run that is acceptable. For a product expected to need field repair, the leaded body is the more practical choice and the same die is available in it. Our kitting service page describes how we stage the reels, the dry pack and the moisture cards for a build so that the line receives one kit rather than a set of partial deliveries.