A stencil is a purchased part with a service life measured in prints. A fixture is a purchased part with a revision that has to match the build. Both sit outside the bill of material, which is why both fail quietly and both show up as a yield problem rather than a tooling problem.
Control here does not mean more paperwork. It means every tool has an identity, a condition that is checked at a stated interval, and a point at which it is taken out of service instead of being used one more shift.
Why tooling escapes the controls that catch everything else
Material and product both have records that follow them: a kit record, a lot record, a serial number. A stencil has a purchase order and then nothing, unless somebody starts a card for it.
A worn stencil produces a print defect that is blamed on the paste, and a fixture with a worn locator pin produces an offset that is blamed on the machine. Both investigations cost more than the tool did, and both repeat on the next build, because the tool was never in the control loop.
The four assets that need a record
Not everything on the line needs a log. Four categories do, because each one can change the product without changing any document.
| Asset | What it controls | What goes wrong without a record |
|---|---|---|
| Stencil | Paste volume and aperture definition | A worn or tensioned out stencil prints short, and the defect is read as a paste or profile issue |
| Printer tooling and pallets | Board location during print | A worn support pin lets the board flex, so paste height varies across the panel |
| Reflow carriers | Board support and thermal mass through the oven | A carrier from a different product changes the thermal profile and the joint quality with it |
| Test fixtures and jigs | Contact and stimulus during electrical test | Worn probes pass a bad unit or fail a good one, and the yield number becomes noise |
Stencil control: what to count and what to check
A stencil card carries an identity, a build reference and a running print count. The checks are simple, and the discipline is in doing them at the stated point rather than when a defect appears.
| Control point | What is checked | When |
|---|---|---|
| Identity | Stencil number, product, revision and thickness marked on the frame | At receipt and at every setup |
| Revision match | The stencil revision equals the build revision in the work order | At setup, before the first print |
| Print count | Counted against the limit set for that aperture size and paste type | At the end of each run |
| Tension | Measured across the mesh and compared to the value recorded when the stencil was new | At the interval written on the card |
| Aperture condition | Inspection for damage, paste build up and deformation after cleaning | At cleaning, and after any print defect |
| Cleaning | Method and solvent recorded, because the wrong solvent shortens life | Per the cleaning schedule |
| Storage | Stored flat in a frame rack, not stacked, with the card attached | At return to store |
| Retirement | Taken out of service at the count or condition limit, and marked as retired | At the limit, not after the next defect |
Fixture and test jig control
A fixture has two jobs that are often confused. It holds the board, and it may also make electrical contact. The holding side wears as a mechanical item, and the contact side wears as an electrical one, so the two are checked separately.
Each fixture carries a tag with the product, the revision it was built for and a service date. Locator pins, clamps and posts are checked against the drawing at a stated interval, and probes are checked for contact resistance. A repaired fixture is re qualified before it returns to the line, because a replaced pin changes the datum.
The revision point is the one that causes scrap. A fixture built for revision B still accepts a revision C board in most cases, and holds it slightly wrong, which produces a failure that looks like a product defect. Matching fixture revision to work order at setup takes a minute.
When a stencil or fixture is remade
A remade stencil is a change to the process, even when the Gerber data is untouched, because the new foil changes paste volume slightly. The remake is tied to the change record, and the first article is inspected as if it were a new build.
How SUPERB PCBA controls tooling on the line
Tooling is set up against the work order, and the first board of a run is checked before the line continues: 3D SPI after print confirms paste volume and height across the panel, and 3D AOI after reflow confirms placement and fillet condition. Placement runs down to 01005 on seven SMT lines, with reflow through a twelve zone oven under nitrogen, so a print or support problem shows up as a measurement rather than an opinion.
X-ray to IPC-7095 with voiding under five percent covers the joints that cannot be seen, and the flow runs seventeen steps with ten QC stations under IPC-A-610 Class 2 and Class 3. The quality system is ISO 9001, with ISO 13485 for medical work, and every build closes with an outgoing record that states what was inspected and on which tooling.
Where a customer supplies the fixture, the same card applies: identity, revision, service date and the check that was done. A fixture that arrives without a revision marked is tagged before use, rather than finding the mismatch at the test station with a full lot built.
Tooling and stencil control questions
How often should a stencil be replaced?
Against a print count limit set for the aperture size and paste type, not against a calendar. Fine pitch and small aperture stencils reach their limit sooner, and a stencil stored well between runs still reaches it. The count is what tells you the limit has arrived. Test coverage that catches the result is under PCBA test coverage strategy.
Does a fixture need calibration?
The mechanical part needs a dimensional check, the electrical part a contact check. Calling both calibration hides the difference, and usually means the mechanical side is never inspected.
What record proves the tooling was right for the build?
The setup record that names the stencil number, the fixture revision and the work order, plus the first article result for that run. A stencil card on its own shows the tool existed, not that it was the correct one. How a tooling change is cut into a running build is covered under engineering change order implementation.
Next step
Send the build you are about to release, with the stencil and fixture list you expect to use and the revision of each. The reply returns the points where a tool could be used past its limit, the fields to add to the tool card, and the first article checks that would catch a wrong revision before the lot runs. For the shop floor side, see PCBA workshop.