Contact Us

STM32G051C8T6

Brand: ST
STM32G051C8T6 is a ARM Cortex-M microcontroller from STMicroelectronics, designed for drone electronics, embedded control systems, and industrial IoT applications. Superb Automation supplies genuine STM32G051C8T6 with full traceability, competitive pricing, and fast global delivery — supporting prototype to production volumes for drone, robotics, and industrial customers worldwide.
quote now

Product Specifications

STM32G051C8T6 — ARM Cortex-M0+ Microcontroller by STMicroelectronics

The STM32G051C8T6 is an STMicroelectronics ARM Cortex-M0+ MCU in LQFP-48(7x7) for Embedded control and general-purpose MCU applications. Supplied by SUPERB Automation.

Part Number Decoded — Field by Field

FieldValueMeaning
STM32G051C8T6Full Part NumberSTMicroelectronics ARM Cortex-M0+ Microcontroller
STM32Product FamilySTMicroelectronics 32-bit ARM-based MCU
G0SeriesARM Cortex-M0+ based MCU — G0 series

Quick Specifications

ParameterValue
ManufacturerSTMicroelectronics
Part NumberSTM32G051C8T6
CoreARM Cortex-M0+
PackageLQFP-48(7x7)
Temperature Range−40°C to +85°C
Supply Voltage1.8V–3.6V

Product Overview

The STM32G051C8T6 is an STMicroelectronics ARM Cortex-M0+ microcontroller in LQFP-48(7x7) package. Part of ST's extensive STM32 portfolio, it delivers a high-performance processing platform with integrated Flash, SRAM, and a rich set of communication peripherals for Embedded control and general-purpose MCU applications. Supplied by SUPERB Automation with full traceability and competitive lead times.

Key Features & Benefits

ARM Cortex-M0+ Core — Efficient Processing for Embedded Control

The ARM Cortex-M0+ core provides deterministic real-time performance with hardware multiply/divide and optional FPU, executing control loops, communication stacks, and sensor fusion algorithms efficiently in resource-constrained embedded environments.

Rich Peripheral Set — GPIO, Timers, ADC, Communication Interfaces

Features a comprehensive set of on-chip peripherals including multi-channel DMA, 12/16-bit ADCs, advanced PWM timers for motor control, and multiple USART/SPI/I²C interfaces for sensor and communication module connectivity.

ST Ecosystem — CubeMX, HAL, LL, Middleware

Fully supported by ST's STM32Cube ecosystem including CubeMX graphical configuration, HAL/LL driver libraries, FreeRTOS integration, and extensive middleware stacks (USB, TCP/IP, FATFS, graphics) — accelerating firmware development and reducing time-to-market.

Target Applications

Embedded Control & IoT Systems

Functions as the main processing unit in embedded control systems, IoT endpoints, sensor hubs, motor controllers, and human-machine interfaces — leveraging the Cortex-M architecture for efficient, low-power operation.

Industrial Automation & Motor Control

Powers industrial motor drives, PLCs, sensor transmitters, and factory automation equipment — taking advantage of advanced PWM timers, high-speed ADCs, and CAN/RS-485 communication for distributed control architectures.

Consumer & Portable Electronics

Integrates into consumer devices, wearables, smart home products, and portable instruments — benefiting from the STM32 family's low-power modes, small packages, and extensive third-party firmware ecosystem.

Frequently Asked Questions

Is the STM32G051C8T6 supported by STM32CubeIDE?

Yes, the STM32G051C8T6 is fully supported in STM32CubeIDE with graphical pinout configuration, clock tree setup, and automatic peripheral initialization code generation — enabling rapid prototyping and production firmware development.

What firmware/RTOS options are available?

The STM32 family is supported by FreeRTOS, Zephyr, NuttX, ChibiOS, and bare-metal HAL programming. For drone applications, Betaflight, iNav, ArduPilot, and PX4 all have STM32 HAL targets.

What is the minimum order quantity (MOQ)?

Contact SUPERB Automation for a tailored quote. We support quantities from prototype tray to full production volumes.

Request a Quote

SUPERB Automation supplies genuine STMicroelectronics STM32G051C8T6 MCUs with full traceability and batch-level QA documentation. Whether you need a single tray for prototype builds or pallet-level volumes for production, we source through verified channels with competitive lead times. Contact us with your target quantity and delivery date — we'll respond with a detailed quotation within 24 hours.

STM32G051C8T6: 1.7 V operation and a DAC pair in 48 pins

The G051 subfamily is the low voltage member of the value line. Where the G030 stops at 2.0 V, this part runs from 1.7 V to 3.6 V on the same Cortex-M0+ at 64 MHz, and it adds two 12-bit DAC channels and two rail to rail comparators that the cheaper line does not carry. The order code here is C for 48 pins, 8 for 64 Kbytes of flash, T for the LQFP body and 6 for minus 40 to plus 85 degrees C with a 105 degree junction.

Inside are 18 Kbytes of SRAM with 16 Kbytes under hardware parity, a 12-bit converter at 0.4 microseconds with up to 16 external channels, 14 timers of which two can run at 128 MHz, a seven channel DMA and a shutdown mode below standby. Figures are from DS13303 Rev 4 of June 2025.

What the subfamily provides

CoreCortex-M0+ at up to 64 MHz
Supply1.7 V to 3.6 V
Flash64 Kbytes on the x8 density, 32 Kbytes on x6, both with a securable area
SRAM18 Kbytes, 16 Kbytes with hardware parity check
ADC12 bit at 0.4 microseconds, up to 16 external channels, 16 bit by oversampling
DACTwo 12-bit channels with low power sample and hold
ComparatorsTwo fast low power, rail to rail, programmable input and output
Timers14, two capable of 128 MHz, including one advanced motor control and one 32-bit
DMASeven channels with flexible mapping
SerialTwo I2C at 1 Mbit per second with SMBus and PMBus, two USART, one low power UART, two SPI at 32 Mbit per second
Low powerSleep, stop, standby and shutdown, calendar RTC with alarm
Temperature6 for 85 degrees C, 7 for 105, 3 for 125
PackageLQFP48, 7 mm by 7 mm; the family also ships in TSSOP20, LQFP32, UFQFPN28, 32 and 48, and WLCSP20

Where 1.7 V changes the product

Two alkaline cells in series start at 3.2 V and end at about 1.8 V under load, and a lithium thionyl chloride cell holds 3.6 V for most of its life and then falls quickly. A part with a 2.0 V floor is out of specification before either chemistry is empty, so the last of the capacity is either wasted or covered by a boost converter that costs current and board space. A 1.7 V floor lets the product run to the end of the cells with a linear regulator or with no regulator at all.

That floor also matters on a supercapacitor backup. A backup that starts at 3.3 V and discharges through a diode has to keep the controller alive for the time it takes to write the last record, and the 300 mV between 2.0 V and 1.7 V is a measurable amount of that window. The same arithmetic applies to a 4 mA to 20 mA loop powered device, where the available voltage across the board is small by construction.

The shutdown mode below standby is the other low power feature worth knowing. A calendar RTC with alarm and periodic wakeup runs through stop and standby into shutdown, so a product that reports once a day can sit at the lowest current the die offers and wake on a date instead of on a timer. That is what a battery product needs when the interval between reports is measured in hours, and it is the difference between a two year cell life and a five year one on the same hardware.

The 18 Kbytes of SRAM is generous next to the 8 Kbytes of the G030, and the extra 10 Kbytes is what allows a Modbus register map, a ring buffer and a display frame to coexist. The MCU cross reference page sets out the memory and the voltage floor of each member of the value line, because those two numbers decide which one a battery product can use.

Two DACs and two comparators on a 48 pin board

A pair of 12-bit DACs at low power with sample and hold is enough for a 0 to 10 V output through an amplifier, for a bias that has to be trimmed at test, or for a reference that a comparator window is built around. On a sensor transmitter this replaces a external DAC and its reference, and it keeps the calibration in firmware rather than in a trim pot.

The comparators are rail to rail with programmable input and output, which means they work at the bottom of the supply range where a standard comparator would need a charge pump. Combined with the comparator output routed to a timer break input, they give a hardware overcurrent trip that does not depend on interrupt latency. On a small pump or a solenoid driver that is the difference between a protected output stage and a burnt one.

Two timers that can run at 128 MHz are unusual on a 64 MHz core: the timer clock is separate, so a PWM edge can be resolved to about 7.8 nanoseconds even though the core is slower. That is what makes a quiet dimmer or a precise heater control possible without an external PWM chip. The power management cross reference page lists the rails and drivers we pair with a controller this size.

On 48 pins the line budget usually works out at six for an analog front end, eight for a display or a keypad, four for two serial buses, four for a motor or a relay bank and the rest for the programming header, the crystal and a few diagnostic points. Several lines carry 5 V tolerance, which removes the level translator in front of an industrial input, and all of them are mappable on external interrupt vectors, so a wake from any of them costs no extra logic.

The 5 V tolerant lines are the other thing a 48 pin board usually needs, because an industrial input arrives as a 24 V signal through a divider and the pin sees more than the rail. Where the divider is not enough, the tolerance is what saves a level shifter and its supply rail on a board that has no room for either.

Temperature grades and the order code

The 6 suffix is minus 40 to plus 85 degrees C ambient with a 105 degree junction, 7 raises the ambient to 105 with a 125 degree junction, and 3 goes to 125 ambient and 130 junction. All three are the same die, so the grade is a test and a guarantee rather than a different part, and it is decided by where the board sits rather than by the application. A controller inside a sealed enclosure beside a relay is the case that needs the 3 grade, and it is worth knowing before the enclosure is signed off.

The package choice is the other half of the order. The same die ships in a 4 mm by 4 mm UFQFPN28 and in a 1.94 mm by 2.40 mm WLCSP20, and those two are for a board where the controller is the largest part on the panel. The leaded LQFP48 is the one to use while the product is at the pilot stage, because it can be reworked and inspected without an X-ray turn. Our kitting service page covers how we stage the reels, the dry pack and the moisture cards for a build like this.

Questions before the order

Is the 1.7 V floor available on every grade? Yes, the supply range is a property of the subfamily, and the grade only changes the temperature limits. Does the part need an external reference? The internal VREFBUF is not part of this value line, so a converter that has to hold 0.1 per cent over temperature needs an external reference on the VREF+ pin. Our incoming inspection plan records the marking and the date code of each reel, which is how a mixed grade delivery is caught at goods in.