INA322EA/2K5
Product Specifications
INA322EA/2K5
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA322EA/2K5 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA322EA/2K5: the dual member of the micropower CMOS instrumentation amplifier family
The INA322EA/2K5 is the dual channel member of the INA321 family, packaged in the wider TSSOP-14 and supplied on a 2500 piece reel. It carries two amplifiers of the same 40 uA per channel CMOS input stage, so a two channel sensor front end can be built from one package instead of two, which matters when the board has a 3 mm wide keep out and the two channels have to share a reference.
Each channel is internally set to 5 V/V and is raised by an external resistor pair, so the same gain arithmetic applies as on the single. The input bias current is 10 pA, the offset is 200 uV and the common mode rejection is 94 dB, held to about 3 kHz. The shutdown pin turns both channels off together and drops the supply current below 1 uA, which is the useful behaviour for a two channel instrument that sleeps between readings.
Key data for the INA322EA/2K5
| Channels | Two, each with its own gain resistor pins, sharing one supply and one shutdown control |
| Gain | 5 V/V internal per channel, raised by two external resistors per channel using the 5 plus 5 times R2 over R1 relationship |
| Supply current | 40 uA per channel operating, below 1 uA in shutdown, with a microsecond scale return to normal operation |
| Input | 10 pA bias current, 200 uV offset, 94 dB common mode rejection held to about 3 kHz |
| Bandwidth | 500 kHz at a gain of 5 with a rail to rail output that reaches within 20 mV of the positive rail |
| Temperature | Minus 55 C to 125 C, the same wide window as the single channel member |
Body, marking and reel data
| Body | TSSOP-14, the dual body named in the family document; the single channel member uses MSOP-8 |
| Reel | 2K5 is 2500 pieces on the catalogue entry, the same suffix convention as the single channel part |
| Naming | The vendor document for this family prints the single as INA321 and the dual under the INA2321 name, while the catalogue entry uses INA322EA; the dual rows in the document are the ones that apply, and the order code should be confirmed against a vendor ship record |
| Document age | SBOS168D dated December 2000 and revised January 2006, so the packaging and moisture data are older than the current convention |
| Pins | Two gain resistor pairs, a shared supply, a shared reference and a single shutdown input |
Where a dual micropower front end pays for itself
Two channels in one package saves a placement and a set of decoupling, but the real gain is matching. Two amplifiers on one die track each other over temperature far better than two packages do, and in a bridge application the two halves of the bridge are often read by two channels that have to drift together for the ratiometric arithmetic to hold. That is the reason the dual exists in this family, and it is why the part turns up in handheld instruments that read a differential pair of sensors.
The constraint is the shared shutdown. Both channels go down together, so a board that reads one channel continuously and the other occasionally cannot use the shutdown to save power on one of them. The supply current is low enough that this is rarely a problem, since both channels together draw 80 uA, but a two channel board that spends most of its life asleep should check whether a single channel part with two gain settings would be cheaper than a dual that never sleeps.
On the gain side the arithmetic is identical to the single, and the external resistors dominate the accuracy above a gain of 20. A matched pair per channel, placed close to the pins and sharing a ground return, keeps the common mode rejection that the die delivers. Our amplifier cross reference lists single and dual members side by side, and the pin to pin cross reference note covers the package change from MSOP-8 to TSSOP-14, which is a footprint change and not a drop in.
Buyer questions on the INA322EA/2K5
Can the two channels be used at different gains? Yes. Each channel has its own gain resistor pins, so one can run at 5 V/V and the other at 200 V/V, as long as both inputs sit inside the shared supply rails.
Is the shutdown pin per channel? No, it is shared, so the two channels sleep together. A board that needs independent power control needs two single channel parts.
Does the dual have the same bandwidth as the single? The amplifier cells are the same and the 500 kHz figure at a gain of 5 applies per channel, but the package inductance and the shared supply pin make the decoupling more important on the dual.
Availability and ordering notes
INA322EA/2K5 is the dual channel member in TSSOP-14 on a 2500 piece reel. The catalogue name and the vendor document name for the dual do not match exactly, so a purchase order should carry the full order code and the package rather than the family name. Where a customer is replacing two single channel amplifiers with this part, the board changes and the gain resistors have to be moved around the new pin positions, which is a footprint change that the substitution note should record.