Contact Us

DRV8304HRHAT

Brand: Texas Instruments
Texas Instruments DRV8304HRHAT is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV8304HRHAT — Power Management & Signal Chain | Superb Automation

DRV8304HRHAT

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV8304HRHAT from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV8304HRHAT: A 38 V Three Phase Gate Driver With Pin Straps Instead of a Register Map

DRV8304HRHAT is a three phase BLDC gate driver with three current sense amplifiers and a hardware interface in a VQFN (RHA) body of 40 pins. It drives six external N channel FETs from 6 V to 38 V, sources 15 to 150 mA and sinks 30 to 300 mA into each gate, and integrates three current sense amplifiers with a calibration input that trims their offset. The H suffix on this order code means the settings are pin straps: a resistor from the IDRIVE pin sets the gate current, one from VDS sets the overcurrent threshold, and one from GAIN sets the amplifier gain. That removes the SPI bring up step and the register map from the firmware, at the cost of having to change resistors to change a setting.

Order code and package

Ordering stringDRV8304HRHAT, VQFN, small reel
Family documentDRV8304, SLVSE39B, November 2017, revised July 2018
Interfacehardware, pin strapped, the H member
PackageVQFN (RHA), 40 pins with exposed thermal pad
Spy variantDRV8304S, same die with SPI, the S member
Supply range6 to 38 V, absolute maximum 40 V
Gate drive15 to 150 mA source, 30 to 300 mA sink, eight settings
Current sensethree amplifiers, gains of 5, 10, 20 and 40 V per V
ProtectionVDS overcurrent, sense resistor overcurrent, UVLO, thermal warning and shutdown
Ambient rangeminus 40 to plus 125 degrees

Electrical parameters that decide the application

Supply range6 to 38 V, absolute maximum 40 V
Operating supply current5 mA typical, 7 mA maximum, outputs idle
Sleep current at 24 V20 uA typical at 25 C, 40 uA maximum
Wake time1 ms
Sleep time200 us
Reset pulse15 to 40 us on the enable pin to clear a latched fault
Logic regulator3.3 V on DVDD, 3.0 to 3.6 V, for the internal blocks
Charge pump7 to 11.5 V above VM, 15 mA available for the high side gates
Peak source current60 mA typical at the middle setting, 15 to 150 mA across settings
Peak sink current120 mA typical at the middle setting, 30 to 300 mA across settings
Dead time, hardware part120 ns fixed
Peak drive time4000 ns before the gate current falls to the hold value
Hold current15 mA source after the peak time
VDS overcurrent thresholds0.15, 0.24, 0.4, 0.6, 0.9 and 1.8 V by resistor
Sense resistor overcurrent0.5 V or 1 V trip on VSENSE
Overcurrent deglitch4.5 us
Current sense gain5, 10, 20 or 40 V per V, set by a resistor on GAIN
Input thresholds1.5 V high, 0.8 V low, 100 mV hysteresis

Family variants and how they differ

DRV8304Hhardware interface, pin straps, the part on this page
DRV8304SSPI interface, same die, register control of the same settings
DRV8301older 6 to 60 V driver with an integrated buck converter
DRV83026 to 60 V driver with a buck and a current sense amplifier pair
DRV8323smart gate driver with SPI, three amplifiers and a wider setting range
DRV8353100 V class driver for higher voltage rails
What the H suffix changessettings by resistor rather than by register
What stays the samethe FET interface, the charge pump and the protection set

Points to check before this part goes on a BOM

The choice between the H and the S member is a firmware decision more than a hardware one. With pin straps the driver is configured before the microcontroller boots, so the gate current and the overcurrent threshold are already correct during the first PWM cycle, and there is no risk of a register write arriving late. That matters in a safety related product where the drive has to behave predictably from the first microsecond. With the SPI member the settings can be changed at run time, the fault details are readable, and the device can be re configured for a different motor without touching the board, which is what a platform with several motor sizes wants.

The gate current setting is the trade between switching loss and electromagnetic interference. At 60 mA source the FET turns on in a few tens of nanoseconds, which keeps the switching loss low and pushes the drain voltage edge fast enough to ring with the parasitic inductance of the phase connection. At 15 mA the edge is slower, the ring is smaller, and the loss rises in proportion to the time spent in the linear region. The resistor on IDRIVE selects one of eight settings, and the practical method is to start in the middle, measure the ring on the phase node at the worst case current, and slow the edge until the peak stays inside the FET rating with some margin. A gate driver that is set too fast is a common cause of a FET that fails at load and passes every bench test.

The three current sense amplifiers are what make field oriented control practical on a single shunt per phase. Each amplifier has a gain of 5, 10, 20 or 40, set by a resistor, and a calibration input that shorts the inputs internally and lets the offset be measured and subtracted. With a 1 mOhm shunt and a gain of 20, a 20 A phase current gives 0.4 V, which uses a reasonable part of a 3.3 V converter range. The calibration step matters because the offset of the amplifier appears as a direct current error in the measured phase current, and that error turns into a torque ripple at the motor shaft. Running the calibration at every power up, with the PWM outputs disabled, takes a few microseconds and removes the offset that would otherwise need a per board trim.

Dead time is fixed at 120 ns on this member, and that is a specification worth reading twice. A FET with a 100 ns turn off time and a 40 ns turn on delay needs a dead time longer than the difference, otherwise both FETs in a half bridge conduct at the same instant and the supply is shorted through them. The 120 ns of this part covers most 60 V FETs in the 5 to 20 mOhm class, but a slower FET or a gate resistor that lengthens the turn off will need more, and the SPI member allows the dead time to be set. The other side of the trade is that a long dead time distorts the current waveform at low duty cycle, which shows up as a minimum controllable current and as torque ripple near zero speed.

Where this order code fits

Three phase BLDC and permanent magnet synchronous motor drives on 12 V and 24 V rails, including pumps, fans, actuators and robotics joints. Hardware strapping suits a fixed motor; the SPI member suits a platform with several motor sizes. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Does it include the FETs? No, it is a gate driver. The six power FETs are external, which is the point: the current rating and the on resistance are chosen for the motor rather than fixed by the driver.

Can it run from a 48 V rail? No. The supply range is 6 to 38 V with a 40 V absolute maximum, so a 48 V bus needs the higher voltage member of the family.

What sets the overcurrent threshold? Two paths: the VDS monitor across the FETs, set by a resistor, and the sense resistor comparator at 0.5 V or 1 V. Both trip the same fault.

Is the 3.3 V regulator able to power the microcontroller? Only in a very small product. DVDD is an internal logic regulator with a limited current budget, and the data sheet does not specify it as a system supply.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.