DRV5032FADBZR
Product Specifications
DRV5032FADBZR
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV5032FADBZR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV5032FADBZR: A Hall Switch That Draws 1.3 uA and Samples the Field 20 Times a Second
DRV5032FADBZR is an ultra low power digital switch Hall effect sensor with a sampled output in a SOT-23 (DBZ) body of 3 pins. It runs from 1.65 V to 5.5 V, which covers a single alkaline cell and a 5 V rail, and it averages 1.3 uA from a 1.8 V supply because it wakes, measures the field, and goes back to sleep 20 times a second instead of running continuously. The FA option is specified with a maximum operate point of 4.8 mT. The part exists for products where the sensor has to live for a year on a coin cell, and the sampling rate is the knob that trades current for response time.
Order code and package
| Ordering string | DRV5032FADBZR, SOT-23, large reel |
| Family document | DRV5032, SLVSDC7H, April 2017, revised December 2024 |
| Sensitivity class | FA, maximum operate point 4.8 mT |
| Sampling rate of this class | 20 Hz family rate, 13.3 to 37 Hz across tolerance |
| Package | SOT-23 (DBZ), 3 pins |
| Other packages in the family | X2SON and TO-92, by option |
| Ambient range | minus 40 to plus 85 degrees |
| Supply range | 1.65 to 5.5 V |
| Output drivers in the family | open drain and push pull, the option fixes which |
| Magnetic responses in the family | omnipolar and unipolar, the option fixes which |
Electrical parameters that decide the application
| Average supply current at 1.8 V | 1.3 uA on the 20 Hz versions |
| Average supply current at 3 V | 1.6 uA typical |
| Average supply current at 5 V | 2.3 uA typical |
| Maximum average current at 25 C | 3.5 uA over the 20 Hz versions |
| Sampling frequency | 13.3 Hz minimum, 20 Hz typical, 37 Hz maximum |
| Sampling period | 27 ms to 75 ms, 50 ms typical |
| Lowest current version | 5 Hz, 0.54 uA at 1.8 V, the FB option |
| Highest current version | 80 Hz, 5.2 uA at 1.8 V, the DG option |
| Operate point, FA class | 4.8 mT maximum, the field that turns the output on |
| Push pull high level | VCC minus 0.35 V at 1 mA sink, VCC minus 0.1 V typical |
| Push pull low level | 0.1 V typical, 0.3 V maximum at 1 mA |
| Open drain leakage | 5 nA typical, 100 nA maximum at 5.5 V |
| Supply range | 1.65 to 5.5 V, absolute maximum 6 V class |
| Ambient range | minus 40 to plus 85 degrees, narrower than the older DRV5023 |
Family variants and how they differ
| DRV5032FB | 5 Hz sampling, 0.54 uA, for a tamper switch that can wait 200 ms |
| DRV5032FA | 20 Hz sampling, 1.3 uA, the part on this page |
| DRV5032DG | 80 Hz sampling, 5.2 uA, for a fast target such as a rotating wheel |
| DRV5032AJ | 9.5 mT maximum operate point, the insensitive option for a strong magnet |
| DRV5032ZE | 63 mT maximum operate point, for a magnet that sits against the package |
| DRV5023 | 2.5 to 38 V, millamp class current, wider temperature range |
| DRV5013 | latch, for rotation counting rather than presence |
| What the option letter changes | sampling rate, magnetic threshold, output driver and package |
Points to check before this part goes on a BOM
The current figure is an average over the sampling cycle, not a quiescent current. The device wakes, biases the Hall plate for a few microseconds, decides, updates the output and shuts the analogue blocks down again, and the rest of the period contributes almost nothing. That is why the 20 Hz version draws 1.3 uA while the 80 Hz version draws 5.2 uA: the wake time is roughly constant, so the current scales with the number of wakes. A product that needs 4 uA of budget has to either accept a 5 Hz version or move to a magnetic reed switch, and the sampling period then sets how long a passing magnet has to stay in front of the sensor.
The sampling rate sets the maximum detectable event rate, and that is the specification most often missed. At 20 Hz the field is measured every 50 ms nominal, and the tolerance on that period runs from 27 ms to 75 ms, so a target that passes in 10 ms can be missed entirely. For a lid or a tamper switch this does not matter, because the mechanical event lasts seconds. For a flow meter or a rotating shaft it matters a great deal, and the 80 Hz version exists for that case with a 12.5 ms nominal period. A pulse counter that needs one count per revolution has to see the magnet for longer than the longest sample period, not the typical one.
The 4.8 mT class on this option is the middle of the magnetic range and the most common choice for a small button magnet at 3 to 5 mm. The output driver type matters more than the threshold in a battery product: a push pull output gives a defined level with no external resistor and no current while idle, while an open drain output needs a pull up that draws current whenever the output is low. Because the family offers both and the option letter fixes which is fitted, the driver type has to be confirmed from the device comparison table in the family document before the BOM is frozen, then checked on the first article.
The 85 degree ambient limit is the one place where this part is not a drop in replacement for the older DRV5023. The DRV5023 covers 125 degrees and the DRV5032 stops at 85, so an industrial product that runs its electronics hot cannot simply trade current for temperature. Where the enclosure stays below 70 degrees internally, the change is straightforward: the supply range now starts at 1.65 V so the sensor can run from the same rail as a low power microcontroller, and the average current falls by three orders of magnitude. Where the board sits next to a motor or a heater, the older family stays the right answer.
What the sampling architecture means for a battery budget
A coin cell of 220 mAh has about 700 coulombs of charge. At 1.3 uA the sensor consumes 1.3 microcoulombs per second, which is 112 coulombs a day, so the sensor alone would flatten that cell in about six days if it ran continuously. That is why the rest of the product has to sleep, and why a 5 Hz version at 0.54 uA is worth considering: it buys a factor of two and a half in standby current at the cost of a 200 ms response. The other lever is to power the sensor from a microcontroller pin and wake it only when the product is awake, which removes the standby budget entirely but also removes the ability to detect a change while the product sleeps. Which of the three approaches fits depends on whether the event to be detected can wait.
Where this order code fits
Battery powered position sensing, tamper detection on meters and enclosures, reed switch replacement in water and gas meters, and any wearable where a microamp matters. The 5 Hz version is the usual pick for tamper and the 80 Hz version for counting. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.
Questions buyers ask
Can it replace a reed switch directly? Electrically yes, with the caveat that the sampling period sets how long the magnet must stay in range. A reed switch responds in microseconds, this part responds within one sample period.
Does the output need a pull up? Only if the option fitted is the open drain one. The push pull option drives both levels and needs no resistor.
Why is the ambient range only 85 degrees? The sampled architecture and the small package set a lower thermal limit than the continuously biased sensors in the DRV5023 family, and the data sheet states 85 degrees as the maximum.
Is the supply current affected by the output state? Slightly, through the output driver and any pull up current, but the dominant term is the number of wakes per second.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.