Contact Us
  • Home
  • COMPONENTS
  • Bridge Rectifiers and Schottky Rectifier Diodes for Power Inputs

Bridge Rectifiers and Schottky Rectifier Diodes for Power Inputs

Glass passivated bridge rectifiers from 600 V to 1000 V and Schottky rectifiers from 40 V to 100 V, with forward voltage and surge current stated per part.
quote now

Product Specifications

Bridge rectifiers and Schottky diodes for power input stages

Product Overview

A bridge rectifier turns an AC input into a DC rail, and its two costs are forward drop and heat. Current passes through two diodes at a time, so the drop adds up: a bridge with 1.1 V per element loses 2.2 V, which is 2.2 W at 1 A and 55 W at 25 A. That is why a 25 A bridge is a metal tab part on a heat sink while a 0.8 A bridge is a small surface mount body that runs on the copper under it.

A Schottky rectifier is used where the drop matters more than the reverse leakage. A 40 V part with 0.5 V forward drop dissipates less than half of what a silicon junction diode would at the same current, which is why it appears in the secondary side of a converter and in reverse polarity protection. The trade is leakage, which rises steeply with temperature, and a reverse voltage limit that is much lower than a silicon part of the same size.

Surge rating is the third figure and the one that decides field failures. A bridge that feeds a capacitor bank sees a large inrush current at every power up, and the non repetitive surge rating is what survives that. A part with a 30 A surge on a 2 A rail is fine for a small adapter, while a 25 A bridge with a 350 A surge is what a motor drive or a battery charger input needs. The rows below keep the surge figure with the average current rather than listing it separately.

Key Specifications

ParameterSmall bridgePower bridgeSchottky rectifier
Reverse voltage600 V to 1000 V600 V to 1000 V40 V to 100 V
Average current0.8 A25 A at 150 C case1 A to 20 A
Forward voltage1.1 V at 0.8 A1.05 V at 12.5 A0.5 V at 3 A on a 40 V part
Surge current30 A for 8.3 ms350 A for 8.3 ms100 A for 8.3 ms on a 3 A part
Leakage5 uA at 25 C10 uA at 25 C, 500 uA at 125 C0.5 mA at 25 C on a 40 V part
Recoverystandard recovery, for line frequencystandard recovery, for line frequencymajority carrier, no reverse recovery
PackageMBS surface mountGBJ with a metal tabSMA, SMC, DO-41, TO-220
Typical useadapter and charger inputdrive and charger inputsecondary side and reverse polarity guard

Included Models and Order Codes

The order codes below are the rectifiers quoted most often for AC adapters, motor drives, battery chargers and reverse polarity protection. Give the AC or DC input voltage, the average current, the inrush seen at power up and the cooling available, and the part and its heat path are confirmed together.

Part NumberTypeReverse VoltageAverage CurrentForward VoltagePackage
MB10Sbridge rectifier, glass passivated1000 V0.8 A1.1 V at 0.8 AMBS surface mount
GBJ2506bridge rectifier, glass passivated600 V25 A at 150 C case1.05 V at 12.5 AGBJ with a metal tab
1N4007standard recovery rectifier1000 V1 A1.1 V at 1 ADO-41 axial
S1Mstandard recovery rectifier1000 V1 A1.1 V at 1 ASMA surface mount
1N5408standard recovery rectifier1000 V3 A1.2 V at 3 ADO-201AD axial
SS14Schottky rectifier40 V1 A0.5 V at 1 ASMA surface mount
SS34Schottky rectifier40 V3 A0.5 V at 3 ASMC surface mount
1N5819Schottky rectifier40 V1 A0.6 V at 1 ADO-41 axial
MBR20100CTdual Schottky rectifier, common cathode100 V20 A total, 10 A per leg0.85 V at 10 A, 25 CTO-220

Key Features

Drop and heat together – the forward voltage is given at the current the part will carry, so the dissipation of a bridge can be worked out before the heat sink is chosen.

Surge with the average rating – the non repetitive surge figure sits on the same row as the average current, because inrush into a capacitor bank is what fails a small bridge.

Leakage at temperature – the reverse leakage is given at 25 C and at 125 C where the maker publishes both, since a Schottky part leaks ten times more when hot.

Standard and Schottky separated – line frequency bridges and majority carrier rectifiers are listed as different types, because a Schottky cannot replace a 1000 V bridge on a 230 V input.

Dual diode packages – the common cathode TO-220 parts put two legs in one package for a centre tapped secondary, which halves the part count on a converter output.

Axial and surface mount – through hole and surface mount versions of the same electrical part are listed, so a service repair and a new build can use the same specification.

Glass passivated junctions – the bridge rows state glass passivation, which is what keeps leakage low after humidity and thermal cycling on a mains side part.

Thermal resistance stated – junction to case figures are published for the tab parts, so the heat sink calculation uses the package rather than an assumption.

Applications

These parts are quoted for the input and output stages of power conversion, typically where: The rectifier sits in the input or output stage of a power board, so it is quoted with the SUPERB PCB and the SUPERB PCBA build for that board.

AC adapters and chargers – a 0.8 A bridge in an MBS body rectifies a 230 V input on a small board, and the 30 A surge covers the inrush into the first capacitor.

Motor drives and inverters – a 25 A bridge on a heat sink feeds the DC bus of a drive, and the 350 A surge rating covers the charging current of the bus capacitor at power up.

Secondary side rectification – a 40 V Schottky in an SMC body rectifies a converter output, and its 0.5 V drop keeps the efficiency above what a junction diode would reach.

Reverse polarity and ORing protection – a Schottky in series with a battery or a supply input drops less than a silicon diode and blocks the reverse path, which is what a handheld instrument with a removable pack needs.

Sourcing and Cross-Reference

Rectifiers are commodity parts with a wide second source, and that is exactly where a wrong substitution hides. A part with the same voltage and current can have a forward drop 0.3 V higher, which on a 3 A output is nearly a watt of extra heat in a package that has no tab. The comparison therefore uses the forward voltage at the operating current, not the headline rating, and the surge rating for the inrush the circuit actually produces.

The second check is the reverse characteristic. A Schottky at 100 V is near the practical limit for the family, and its leakage at high temperature can be large enough to matter in a battery path. A silicon junction part of the same current has a higher drop but a much lower leakage, and the choice between them is made on the duty cycle rather than on the datasheet front page.

Availability is good for the axial and SMA parts and tighter for the tab packages during a power supply cycle. The quotation line states the package, the batch date and the quantity, and for a production run the part is bought against a build schedule rather than against a single order.

For volume builds, SUPERB Assembly support covers the thermal pad solder coverage, the tab screw torque and the conformal coat around a mains side bridge.

Q: Can you supply a bridge or Schottky rectifier with the same footprint when the original part is discontinued?

A: Yes. Send the current part number, the reverse voltage, the average current, the inrush and the package, and the SUPERB Tech sales team will confirm the nearest part that keeps the footprint and the surge rating.

Why Buyers Source Rectifiers Through SUPERB

  1. Forward drop at the real current: the comparison uses the voltage at the current the part will carry, so a substitute does not add a watt of heat to a package with no tab.
  2. Surge matched to inrush: the non repetitive surge rating is checked against the capacitor charging current, which is what fails small bridges in the field.
  3. Leakage at temperature: Schottky leakage at 125 C is part of the comparison, particularly in a battery path where it discharges the pack.
  4. Package held for service: axial and tab packages are tracked alongside the surface mount parts, so an existing board can be repaired with the same specification.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Discrete and power semiconductors, IGBTs and SiC power devices, TVS and ESD protection diodes, PFC controllers, Pin to pin cross reference.