Contact Us

VBTA1290

Brand: VBsemi
VBsemi VBTA1290 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBTA1290 — Discrete & Power Semiconductors | Superb Automation

VBTA1290

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBTA1290 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBTA1290: a 20 V N channel switch in a three pin SC-75A body

The VBTA1290 is an N channel trench MOSFET in the SC-75A body, which is the three pin SOT-416, and everything about it follows from that package. The product summary prints 91 milliohm typical at a 10 V gate and 2.0 A, 107 milliohm at 4.5 V and 1.8 A, and 141 milliohm at 2.5 V and 1.6 A, against a 20 V drain to source rating. The drain current row carries a footnote that says package limited, and that footnote is the honest description of the part.

The listed applications are the small switch jobs: portable devices with a load switch and a battery switch, and load switching for motors, relays and solenoids. That last line is the important one, because a relay coil or a solenoid is an inductive load that wants a device rated for a pulse and a body diode that can absorb a clamp, and the timing rows on this sheet show that it is not a high frequency switch at all.

The timing rows are the reason it cannot be used as a converter switch. At a 10 V gate the turn off delay is 3 microseconds typical and 6 microseconds maximum, and at a 4.5 V gate the turn off delay is 1.9 microseconds with a fall time of 0.75 microseconds. A part that takes 2 to 6 microseconds to turn off is an on and off switch for a load that changes state a few times a second, and any attempt to run it at even 10 kHz spends most of the period in the linear region.

What it does well is conduct from a low gate rail. The 141 milliohm row at 2.5 V means a product running from a single lithium cell can still switch a 1.6 A load with the gate driven directly from the cell, and the threshold window of 0.6 V minimum to 1.3 V maximum is narrow enough that a 2.5 V rail always has overdrive. The cost is 364 mW of conduction at 2 A, against a 2.8 W case row and a 1.56 W air row.

The parameter table in full

Drain to source voltage20 V
Gate to source voltage, continuousplus or minus 12 V
On resistance at 10 V gate and 1.7 A91 milliohm typical
On resistance at 4.5 V gate and 1.2 A107 milliohm typical
On resistance at 2.5 V gate and 1.0 A141 milliohm typical
Continuous drain current, case at 25 C2.0 A, package limited
Continuous drain current, case at 70 C1.6 A, package limited
Continuous drain current, ambient at 25 C2.0 A, package limited
Continuous drain current, ambient at 70 C1.6 A, package limited
Pulsed drain current, 300 microsecond pulse20 A
Continuous source to drain diode current, case at 25 C2.3 A, package limited
Continuous source to drain diode current, ambient at 25 C1.3 A
Maximum power dissipation, case at 25 C2.8 W
Maximum power dissipation, case at 70 C1.8 W
Maximum power dissipation, ambient at 25 C1.56 W
Maximum power dissipation, ambient at 70 C1.0 W
Junction to ambient, 5 s pulse60 C per watt typical, 80 maximum
Junction to ambient, steady state125 C per watt maximum
Junction to foot, steady state34 C per watt typical, 45 maximum
Operating junction and storage rangeminus 55 to plus 150 C
Gate threshold at 250 microamp0.6 V minimum, 1.3 V maximum
Breakdown voltage temperature coefficient23 mV per C
Gate leakage at plus or minus 4.5 V and at plus or minus 12 V0.5 and 25 microamp
Drain leakage at 20 V, 25 C and 55 C1 and 10 microamp
On state drain current at 4.5 V gate15 A
Forward transconductance at 3.7 A17 S
Total gate charge at 10 V gate8.8 nC typical, 13.5 nC maximum
Total gate charge at 4.5 V gate4 nC typical, 6 nC maximum
Gate source and gate drain charge0.9 and 1.1 nC
Gate resistance at 1 MHz0.4 minimum, 2 mean, 4 maximum ohm
Turn on delay and rise time at 4.5 V gate0.29 and 0.4 microsecond typical
Turn off delay and fall time at 4.5 V gate1.9 and 0.75 microsecond typical
Turn on delay and rise time at 10 V gate0.1 and 0.15 microsecond typical
Turn off delay and fall time at 10 V gate3 and 0.75 microsecond typical
Body diode forward drop at 3.7 A0.85 V typical, 1.2 V maximum
Body diode reverse recovery time and charge12 ns and 5 nC typical
PackageSC-75A, three pins, also listed as SOT-416
Capacitance rowsnot published on this sheet

What the thermal rows allow in a 60 C cabinet

The three pin body is the whole thermal argument. Junction to foot is 34 C per watt typical and 45 maximum, and junction to ambient at steady state is 125 C per watt. Two amps through 91 milliohm is 364 mW, which is 12 C of rise on the typical foot path and 16 C on the maximum, so the part runs cool as long as the two amp figure is real.

In air the same 364 mW through 125 C per watt is 46 C of rise from a 25 C room, and 71 C from a 60 C cabinet, which leaves the junction at 131 C. The 1.56 W the sheet allows at 25 C ambient is the ceiling that corresponds to a 125 C rise, and at 1.56 W the part is drawing 4.1 A at 91 milliohm, well above the 2 A package row. The thermal path is therefore not the limit at 2 A; the three pin lead frame is, which is the meaning of the package limited footnote on every current row.

The two rows that matter for a relay or solenoid driver are the 20 A pulsed row at 300 microseconds and the body diode recovery charge of 5 nC. A coil at 12 V and 100 mA that is switched off puts the drain well above 20 V, so the clamp has to be external, and the body diode will carry the coil current for the duration of the clamp. The sheet gives 2.3 A of continuous diode current at a 25 C case, which is enough for the coil and not enough for a solenoid of any size.

Where the printed rows in this sheet disagree

The first is the missing capacitance table. The specification page goes from the transconductance row straight to the gate charge rows, with no input, output or reverse transfer capacitance anywhere on the sheet. A part with 8.8 nC of gate charge at 10 V and no capacitance rows cannot be checked for its Miller interval, and any driver calculation has to fall back to the charge figure alone.

The second is the gate resistance unit. The table prints 0.4 minimum, 2 mean and 4 maximum with a unit of kilohm against 1 MHz. Four kilohm of internal gate resistance would make the part unusable above a few kilohertz, and the same rows on every sibling sheet carry ohms. The figure is ohms; the unit column is wrong, and we quote it as ohms with that caveat.

The third is the diode current against the drain current. The continuous source to drain diode current is printed as 2.3 A at a 25 C case while the continuous drain current is 2.0 A in the same package. A body diode that carries more current than the channel is possible when the diode is larger than the channel area or when the two rows were computed from different limits, but it is not something to build on, and both rows are marked package limited.

The fourth is the ambient current rows, which are identical to the case rows at both temperatures. The 2.0 A at 25 C ambient and 2.0 A at 25 C case cannot both be right if the ambient path is 125 C per watt and the foot path is 34, and the reason they are identical is again the package limited footnote, which overrides the thermal calculation. It is printed, but it is easy to read past.

Where a 20 V, 2 A three pin part still fits

It fits a load switch in a handheld product, where the board has almost no room, the current is under two amps and the switch changes state when a user presses a button. It fits a relay or small solenoid driver on a 12 V rail, with an external clamp diode, and there the 20 A pulse row and the 5 nC recovery charge are the useful figures. It fits a battery switch in a single cell product where the gate comes straight from the cell and the 141 milliohm row at 2.5 V is inside the budget.

It does not fit anything that switches faster than a few kilohertz, for the timing reason above, and it does not fit a reverse blocking position because an N channel body diode points from source to drain and will conduct whenever the output rises above the input. It also does not fit a rail above 20 V, and the 23 mV per C breakdown coefficient means a hot part is at 18.4 V in magnitude at a 125 C junction, so a 20 V rail is outside the envelope once the part warms up.

Our power management cross reference work treats the three pin SC-75A as its own footprint class, because the SOT-416 pin spacing, the lead width and the die pad differ from the SOT-23 that most people substitute by eye. For this family the obsolete part cross reference hub is where we hold the small signal switches that have gone end of life, since this body size is the first to disappear when a vendor trims a portfolio.

Questions we answer before a reel is booked

The first is the load type. A relay coil, a solenoid and a capacitive load each stress a different row on this sheet, and only the coil is covered by the published diode figures. Ask what the load looks like at switch off, because the 20 V rail plus the coil inductance will exceed the drain rating without an external clamp, and the clamp is not optional here.

The second is the gate drive source. If the gate is driven from a 2.5 V rail the part is a 141 milliohm switch and the 1.6 A row applies; from a 10 V rail it is 91 milliohm but the turn off delay stretches to 3 microseconds. Both are usable and neither is the row on the front page.

The third is the marking and the reel. A three pin body of this size carries a short code, and the sheet publishes no orderable addendum, no packing column and no moisture level, so the reel size, the marking and the floor life have to be confirmed on the delivered label. Our incoming inspection plan checks the on resistance at 2.5 V and at 4.5 V on this family, because a part that has drifted to 141 milliohm at 4.5 V will still pass a 10 V test and fail in the product.