Contact Us

VBQG2216

Brand: VBsemi
VBsemi VBQG2216 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBQG2216 — Discrete & Power Semiconductors | Superb Automation

VBQG2216

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBQG2216 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBQG2216: a minus 20 V P channel for battery and load switching

The VBQG2216 is a single P channel MOSFET in the DFN 2 by 2 body, printed at minus 20 V drain to source with 20 milliohm at a minus 10 V gate, 28 milliohm at minus 4.5 V and 40 milliohm at minus 2.5 V, drawing minus 10 A at a 25 C case and minus 8 A at a 70 C case. The data sheet names portable devices, load switch, battery switch and charger switch. Three resistance columns at three gate voltages is the most useful thing on the sheet, because a P channel in a battery path is often driven from a rail that is not 10 V.

A P channel is used in the positive line when the gate drive has to be referenced to the source, which sits at the battery voltage. Pulling the gate to ground turns the part on, and the drive available is whatever the battery provides, so a nearly flat battery gives a weak gate and a higher resistance. The 40 milliohm at minus 2.5 V is the column that describes that condition, and it is double the 20 milliohm at a full gate.

The part is a trench device with a fifth of the resistance of a planar P channel of the same area, which is why 20 milliohm fits in a 2 mm square. It is still roughly four times the resistance of an N channel of the same size at the same voltage, and that asymmetry is the reason a battery switch is sometimes built as an N channel in the negative line when the circuit allows it.

Key data for the VBQG2216

ConfigurationSingle P channel
PackageDFN 2 by 2 with exposed pad
VDSMinus 20 V
RDS(on) at minus 10 V20 milliohm
RDS(on) at minus 4.5 V28 milliohm
RDS(on) at minus 2.5 V40 milliohm
ID at a 25 C caseMinus 10 A
ID at a 70 C caseMinus 8 A
ID at a lower gateMinus 6 A on the reduced drive column
Gate charge20 nC typical
Gate windowPlus or minus 12 V on the gate according to the summary table
TechnologyTrenchFET P channel
ComplianceHalogen free to IEC 61249-2-21, RoHS to 2002/95/EC
ApplicationsPortable devices, load switch, battery switch, charger switch

The three resistance columns turn into a useful derating table. On a two cell pack at 7.4 V nominal the gate can be pulled to ground through a 100 k resistor and the part sees the full minus 7.4 V, which puts it between the 4.5 V and 10 V columns, so about 24 milliohm. At 3 A that is 0.22 W, and the part stays cool. On a single cell at 3.6 V the same circuit gives minus 3.6 V, which sits below the 4.5 V column and closer to the 2.5 V one, so about 35 milliohm and 0.32 W at the same current.

The gate charge of 20 nC is larger than the N channel parts in this body, which is normal for a P channel of the same resistance because the die is bigger. At a 100 kHz switching frequency the drive current is 2 mA, and the gate resistor that sets the turn on is usually 10 to 100 k in a battery switch because the part is not switched fast. In a load switch that has to limit inrush, the gate is charged through a resistor and a capacitor, and the 20 nC is the charge that has to be moved before the part is fully on.

Where a minus 20 V P channel is used

The first case is a battery switch in a handheld instrument. The part sits between the pack and the system, the gate is pulled to the pack negative by a small N channel when the button is pressed, and the body diode gives reverse polarity protection for free when the pack is inserted backwards. The 20 milliohm at a full gate costs 20 mV at 1 A, which is less than the tolerance on most rails.

The second case is a charger switch. The charger output and the battery are tied through two P channels so that either can feed the system without back feeding the other. The part has to be on with a gate at the charger voltage, which may be 5 V, putting it in the 4.5 V column at 28 milliohm. At 2 A that is 0.11 W in a 2 by 2 body, which is comfortable.

The third case is a load switch for a peripheral rail that has to be sequenced. Here the part is chosen for the low gate drive, because the control logic sits on a 1.8 V domain and the gate is pulled down through a level shift transistor to the battery rail. The 40 milliohm at minus 2.5 V is what the circuit actually gets at the start of the sequence, and the current at that moment is the inrush into the peripheral capacitance, so the safe operating area matters more than the steady state resistance.

Drive, inrush and the body diode

In a P channel load switch the inrush is set by the gate slew, not by the part. Charging the gate through a 100 k resistor with 20 nC of gate charge gives a turn on of about 2 ms, and that is usually too fast for a rail with 100 microfarad of capacitance. A 1 microfarad capacitor from gate to source stretches the turn on and keeps the part out of the region where it dissipates the whole inrush as heat.

The body diode faces the load when the part is off, so a reversed battery is blocked and a load that is driven from another source cannot push current back into the pack. The forward drop of a P channel body diode is 0.7 to 0.9 V, and on a 2 A load that is 1.6 W in the diode before the channel takes over, which is why a load switch that is meant to work during a brownout needs the channel on rather than relying on the diode.

Where the same battery path carries two different codes across several products, the BOM consolidation page covers how a family is merged onto fewer codes without losing a qualification. In this band the three gate voltage columns make the merge easy to justify, because one part covers a single cell and a two cell build as long as the resistance at the lower gate is accepted.

What to check before this code is bought

The summary table prints the gate window as plus or minus 12 V, which is tighter than the plus or minus 20 V common on N channel parts in this body. On a 12 V battery line, pulling the gate to ground puts the full 12 V across the gate oxide, which is exactly at the limit. A rail that can reach 14 V in charge will exceed it, and a zener clamp from gate to source is the usual answer.

The sheet gives no avalanche rating and no safe operating area curve in the text we read, which matters for a load switch with a large output capacitance. Without an SOA curve the inrush has to be limited by the gate slew and verified on the bench, not calculated from a single pulse rating.

Where the code has to be compared with an N channel alternative in the negative line, the how to verify a drop in replacement page covers the bench checks, from threshold and gate charge to the body diode direction, that decide whether the substitute behaves the same in the circuit. The polarity change is the trap: an N channel in the negative line has its body diode facing the other way, and a board built for a P channel will not work with it even when the footprint matches.

The halogen free and RoHS statements on the sheet are the 2002/95/EC version rather than the later recast. That is fine for most builds, but a customer who audits against the current directive will ask for a declaration that names it, and the vendor should be asked for that document rather than assuming the older statement covers it.

Questions we get on this code

Can the gate be tied directly to ground to turn it on? Only if the battery never exceeds 12 V. The gate window is plus or minus 12 V on this part, and a 12 V pack at 14 V in charge is over it. A 10 k resistor and a 12 V zener from gate to source is the safe arrangement.

What is the resistance at 3.3 V of gate drive? Between the 28 milliohm printed for 4.5 V and the 40 milliohm for 2.5 V, so about 33 milliohm. The sheet does not print a 3.3 V column and we do not interpolate one as if it were measured.

Does the body diode need a parallel Schottky? Only if the circuit has to work while the channel is off. The diode drop is 0.7 to 0.9 V, and a Schottky in parallel takes most of that away, at the cost of a part and a leakage path.

Is this part available in an automotive grade? Not on this sheet. There is no AEC-Q101 document and no temperature grade beyond the industrial range, so a vehicle build needs a different code rather than a different label on this one.