Contact Us

VBQG1101M

Brand: VBsemi
VBsemi VBQG1101M is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBQG1101M — Discrete & Power Semiconductors | Superb Automation

VBQG1101M

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBQG1101M from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBQG1101M: a 100 V N channel in the 2 by 2 DFN

The VBQG1101M is a single N channel MOSFET in the DFN 2 by 2 body, printed at 100 V drain to source, plus or minus 20 V on the gate, 75 milliohm at a 10 V gate and 80 milliohm at 4.5 V, with a 1.8 V threshold and 7 A at a 25 C case that falls to 2.5 A at a 25 C ambient. It is the high side switch of a small buck converter, and the data sheet names notebook CPU core as the application. A hundred volts in a 2 mm square body is unusual, and it is bought for two reasons: the headroom it gives on a 48 V or a telecom 60 V rail, and the fact that the small body keeps the switching loop short.

Hundred volt parts normally sit in a 3 by 3 or a 5 by 6 body because the drift region needed for the voltage takes area. Here the die is small and the current is small with it, 7 A at a 25 C case. A buyer who reads 100 V and 7 A and expects both at once will be disappointed, because the two figures belong to different conditions and the ambient rows are 2.5 A and 1.8 A. The part is honest about this, and the four current rows are the most useful lines on the sheet.

The resistance is nearly flat between the two gate voltages, 75 milliohm at 10 V and 80 milliohm at 4.5 V, which says the channel is short and the threshold is low enough that 4.5 V already drives it hard. A flat curve like that is convenient because the same part can be driven from a 5 V rail without the loss penalty that a thick gate oxide part carries.

Key data for the VBQG1101M

ConfigurationSingle N channel
PackageDFN 2 by 2 with exposed pad
VDS100 V
VGSPlus or minus 20 V
Vth1.8 V typical at 250 microamp
RDS(on) at 10 V75 milliohm at 10 A
RDS(on) at 4.5 V80 milliohm at 9 A
ID at a 25 C case7 A, 5.6 A at a 70 C case
ID at a 25 C ambient2.5 A, 1.8 A at a 70 C ambient
Power at a 25 C case4.1 W, 2.2 W at a 25 C ambient
Ciss1400 pF at 15 V
Gate charge15 nC typical, 23 nC maximum in the table, 7.2 nC in the summary line
Body diode0.8 V at 5 A, 15 ns recovery typical
Avalanche20 A single pulse, 21 mJ at 0.1 mH
RthJA39 K per watt typical, 55 maximum at 10 s
Junction rangeMinus 55 to 150 C

Two figures on this sheet disagree and neither should be quoted alone. The product summary prints 7.2 nC for the gate charge, while the electrical table prints 15 nC typical and 23 nC maximum for the same part at a 15 V drain and a 10 V gate. A factor of two between them is not rounding, and it changes the drive current a controller has to supply at a given frequency. Treat 15 nC as the working number, 23 nC as the number a driver has to survive, and ask the vendor to confirm which of the two the summary line was meant to print before the code goes onto a costed BOM.

The thermal numbers say the same thing as the current rows. With the case at 25 C the part may dissipate 4.1 W, and with the ambient at 25 C it may dissipate 2.2 W, because the junction to ambient resistance is 39 K per watt typical and 55 maximum at a 10 s pulse. At 2.5 A and 75 milliohm the conduction loss is 0.47 W, which leaves room against 2.2 W until the ambient rises. At the 7 A case figure the loss would be 3.7 W and the part would be at its ceiling with the case held at 25 C, which is a condition no board provides.

Where a 100 V part in a 2 by 2 is used

The first case is the input stage of a 48 V to 12 V converter in a communications board. The switch node sees the full 48 V plus the ringing, and a 60 V part has no margin once a 10 to 15 V overshoot is added. The hundred volt rating buys that margin, and the 2.5 A ambient current is enough for a 20 to 30 W rail at a switching frequency high enough to keep the inductor small.

The second case is a high side switch in a 48 V hot swap or a load disconnect. The part sits in the positive line, the gate is pumped above the rail by a small charge pump, and the current is limited by the sense resistor rather than by the switch. Here the hundred volt rating matters less than the gate drive headroom, and a 4.5 V capable part driven from a 5 V rail with its source at 48 V still needs the pump, so the low threshold is not a substitute for it.

The third case is a telecom line card where a 60 V rail with a lightning induced surge requirement is present. A hundred volt part plus a clamp is the usual combination, and the avalanche rating of 21 mJ at 0.1 mH defines how much energy the clamp may let through before the part is at risk.

Drive, switching and loss in a 2 by 2

The gate charge of 15 nC typical means 15 mA of drive at 1 MHz and 7.5 mA at 500 kHz, which a controller output can supply directly. The gate resistor is the control: at 5 ohm with a 3 A driver the turn on takes about 25 ns, and the drain ringing on a long input trace is what usually sets the floor. A 100 V part has more headroom for that ringing than a 60 V part, which is another reason the voltage class is bought.

The 1400 pF input capacitance is the figure that matters for the driver, not the gate charge, when the part is switched at 500 kHz or above. Two of these in parallel halve the resistance to 37 milliohm and double the capacitance to 2800 pF, and the pair still needs only 30 mA of drive at 1 MHz. Where a single larger part in a 3 by 3 is the alternative, the choice usually comes down to board area against the thermal path, and the 2 by 2 wins on area while the 3 by 3 wins on the 39 against 32 K per watt junction to ambient.

Where the code on a running board has to be compared with a part from another vendor in the same footprint, the how to verify a drop in replacement page sets out the bench checks, from threshold and gate charge to the body diode direction, that decide whether the substitute behaves the same in the circuit. The 2 by 2 land pattern is common across several vendors, so the package rarely blocks a swap and the gate charge and the threshold usually do.

What to check before this code is bought

The sheet carries an industrial qualification only. There is no AEC-Q101 document, no automotive temperature grade beyond 150 C, and no statement about the moisture sensitivity level of the body. A build for a vehicle rail needs the automotive document and this part is not sold against one, so it should be treated as an industrial part until the vendor produces the paper.

The 100 per cent gate resistance and 100 per cent unclamped inductive switching tests are process controls, not reliability grades. They say every unit was screened, not that the part is qualified for a particular mission profile. Where a build needs that distinction written down, the power management cross reference page sets out which parameters have to match before a substitute is proposed, from threshold and gate charge to the avalanche rating, and how a screening claim is separated from a qualification claim.

The body diode is worth a check on any circuit where the part works as a synchronous rectifier. The forward drop is 0.8 V typical at 5 A and the reverse recovery is 15 ns typical, 30 ns maximum, with 6 nC of recovered charge. In a hard switched half bridge those numbers decide the dead time and the loss spike, and on a 48 V rail a slow recovery in the low side switch can push the high side drain above its rating even with a 100 V part.

Packing matters on a part this small. The reel label is the only reliable record after reflow because the laser mark on a DFN 2 by 2 is hard to read under a microscope, let alone by eye. Where a build needs lot traceability, the 2 by 2 body should be bought on a full reel with a lot code printed on the label, and the reel should not be mixed across lots on the line.

Questions we get on this code

Is 7 A a continuous rating on a board? No. It is the case held at 25 C. At a 25 C ambient the sheet prints 2.5 A, and at a 70 C ambient 1.8 A. On a board with a few square centimetres of copper the practical continuous current is 2 to 2.5 A, and 3 A only with vias into an inner plane under the pad.

Can the part be driven straight from 3.3 V logic? Only as a switch with almost no current. At 3.3 V the part is barely enhanced, and the resistance is well above the 80 milliohm printed for 4.5 V. The 1.8 V threshold leaves 1.5 V of overdrive, which is not enough for a switching application and is marginal even for a load switch.

Why is the gate charge different in two places on the same sheet? We do not know, and we do not smooth it. The summary prints 7.2 nC and the table prints 15 nC typical with a 23 nC maximum. Until the vendor confirms, size the driver for 23 nC and the loss for 15 nC.

What happens if the load is inductive? The body diode clamps the drain to the source plus a diode drop, and the energy in the inductance has to go somewhere. The avalanche rating is 21 mJ at 20 A and 0.1 mH, and a freewheel diode is cheaper than finding that limit on a qualification build.