Contact Us

VBQF4338

Brand: VBsemi
VBsemi VBQF4338 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBQF4338 — Discrete & Power Semiconductors | Superb Automation

VBQF4338

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBQF4338 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBQF4338: two 30 V P channels in a DFN 3 by 3

The VBQF4338 is a dual P channel MOSFET in the DFN 3 by 3 body, printed at minus 30 V drain to source and plus or minus 20 V on the gate. Each leg is 38 milliohm at a minus 10 V gate and 60 milliohm at minus 4.5 V, with 6.4 A at a 25 C ambient over a 10 second pulse and 4.3 A in the steady state. The vendor files it under portable battery switch and load switch, which is exactly what a P channel pair is for: a high side switch that needs no charge pump and no gate rail above the supply.

The body carries the drain pads on the bottom and the sources and gates on the top, in a 3.30 mm square outline. Thermal resistance is 35 C per watt for a 10 second pulse and 75 C per watt in the steady state, against 4 C per watt junction to case, so the copper under the pad is doing the work. The part is halogen free to IEC 61249-2-21 and the vendor states a new low thermal resistance package, which in practice means the exposed pad is larger than the older 3 by 3 outline.

Ratings and the numbers behind them

Drain to source voltageminus 30 V
Gate to source voltageplus or minus 20 V
On resistance at minus 10 V gate38 milliohm at 6.4 A
On resistance at minus 4.5 V gate60 milliohm at 5 A
Continuous drain current, 10 s6.4 A at 25 C, 4.6 A at 85 C
Continuous drain current, steady state4.3 A at 25 C, 3.1 A at 85 C
Pulsed drain current20 A
Continuous source current, diode2.3 A at 25 C, 1.1 A in steady state
Power dissipation, 10 s2.8 W at 25 C, 1.5 W at 85 C
Power dissipation, steady state1.3 W at 25 C, 0.85 W at 85 C
Junction to ambient, 10 second pulse35 C per watt typical, 44 maximum
Junction to ambient, steady state75 C per watt typical, 94 maximum
Gate threshold voltageminus 1.0 V minimum, minus 3.0 V maximum
Total gate charge14 nC typical, 21 nC maximum
Body diode forward voltageminus 0.8 V typical, minus 1.2 V maximum

Reading the rows rather than the front page

The threshold window runs from minus 1.0 V to minus 3.0 V at 250 microamp, and for a P channel that means the gate has to be pulled a full 3 V below the source to guarantee conduction on the worst die. A 3.3 V rail used directly as the gate drive therefore sits exactly on the edge of the window, which is why a P channel load switch on a 3.3 V system is often driven by a small N channel pull down rather than by a logic pin. At 5 V or 12 V the margin is comfortable, and at 1.8 V this part does not switch with any certainty.

On resistance is quoted at each gate voltage with its own test current, and the 38 milliohm at 10 V against 60 milliohm at 4.5 V is a 58 per cent increase for a 5.5 V change in drive. The gate charge of 14 nC typical and 21 nC maximum is small enough to drive from a logic output through a resistor, and the gate to drain charge of 3.8 nC keeps the Miller plateau short, so a slow edge is a choice rather than a constraint. Gate resistance is a fixed 8.5 ohm, which is high for a switching part and tells the reader that this body is intended for on and off control rather than for pulse width modulation.

The switching times support that reading: 10 ns turn on delay, 12 ns rise, 38 ns turn off delay and 28 ns fall, measured into a 15 ohm load with a 6 ohm gate resistor. The asymmetry, with turn off roughly three times slower than turn on, is normal for a P channel because the gate is discharged through the same resistor against a source that is moving. Reverse recovery of the body diode is 20 ns typical and 40 ns maximum, which is fast for a P channel and matters when the pair is used as a synchronous rectifier on the low side of a small converter.

Where the part is used

The first use is a battery switch in a handheld product: one leg disconnects the pack, the other disconnects the charger, and both sit high side so the ground stays solid for the radio and the sensor. At 6.4 A pulsed and 4.3 A steady, the part suits a single cell or two cell product drawing 2 to 3 A continuously with a 6 A peak, which covers most handheld instruments. The second use is a load switch for a peripheral rail, where the P channel keeps the control pin referenced to ground through a small N channel and the off state blocks the rail.

The pair also works as a two channel switch in a portable medical device, where one leg powers the sensor head and the other the pump, and the two can be sequenced without a second package. In that setting the 1.1 A diode rating becomes the limit during a discharge event, because the body diode of a P channel conducts when the output is pulled above the input. A build with a large output capacitor and a hot plug connector should check that path rather than assume the 4.3 A channel rating covers it.

Sourcing notes and the second source question

P channel parts are the ones customers most often try to replace with an N channel plus a charge pump, and the swap is not free: the drive, the quiescent current and the fail safe state all change. When the requirement really is a drop in, the comparison has to be made on threshold voltage, on resistance at the gate voltage actually available, and gate charge at that same voltage. Our power management cross reference keeps the table to those rows, because a P channel that matches at 10 V can be a poor match at 4.5 V and the reverse is also true.

Where a customer wants a second source for a qualified product, the sequence in how to verify a drop in replacement applies with one addition for P channels: the off state leakage and the gate pull up resistor have to be checked at the highest ambient, because a leaky P channel with a weak pull up turns itself partly on and the product drains its pack in storage. We supply this code on the standard 3 by 3 reel with the date code on the label, and we can quote the pair as one line item with a shared date code where the build needs it.

What buyers ask us about this part

The first question is whether a 30 V part is enough for a 24 V battery pack. It is not, once the charger reaches 29.4 V and the pack sees a transient; the part needs headroom, and a 40 V or 60 V P channel is the honest answer for a 24 V system. The second is whether 6.4 A can be held continuously. It cannot: that is a 10 second figure at a 25 C ambient, and the steady state number is 4.3 A at the same ambient and 3.1 A at 85 C.

The third question concerns the leadless body. The vendor note states that a solder fillet at the exposed copper tip of a leadless package cannot be guaranteed, and that manual rework with an iron is not recommended. A prototype line that reworks by hand will damage a share of these parts, and the inspection step has to look at the voiding under the pad rather than at the toe of a joint that does not exist.

On supply, this code is a catalogue item rather than a custom build, and the reel quantity and date code are printed on the label. We hold the incoming record for each lot, including an on resistance sample at minus 4.5 V, because the difference between a good and a marginal lot of P channels shows up at the low gate voltage rather than at 10 V.