Contact Us

VBQF3638

Brand: VBsemi
VBsemi VBQF3638 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBQF3638 — Discrete & Power Semiconductors | Superb Automation

VBQF3638

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBQF3638 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBQF3638: a dual 60 V pair with PWM tuned silicon

The VBQF3638 is a dual N channel MOSFET in the DFN 3 by 3 body, two independent 60 V devices, 28 milliohm at a 10 V gate and 38 milliohm at 4.5 V, 25 A per device, 7.1 nC of gate charge and a 1.7 V threshold. The vendor describes the silicon as PWM optimized, which in practice means the gate charge and the output charge were traded against on resistance rather than the other way round. The junction to ambient resistance is 26 K per watt typical and 35 maximum, with 4 K per watt to the case.

Sixty volts in a dual 3 by 3 body is the highest voltage in this band, and the resistance shows it: 28 milliohm against 16 on the 30 V pair. The drift region doubles in length and the die has to be larger for the same channel resistance, so a dual 60 V part in a 3 by 3 footprint is a compromise between the voltage and the thermal path. At 25 A per device it is a 5 by 6 class part squeezed into a 3 by 3 body.

The applications named by the vendor are system power DC to DC and, in the family description, telecom and industrial supplies. A 48 V telecom rail with a 60 V part leaves 12 V of margin above the 57 V float, which is the usual rule for a switching node that rings. Anything above a 48 V rail needs a 100 V part, and that is a different body.

Key data for the VBQF3638

ConfigurationDual N channel, independent
PackageDFN 3 by 3, split pads
VDS60 V per device
VGSPlus or minus 20 V
Vth1.7 V typical
RDS(on) at 10 V28 milliohm
RDS(on) at 4.5 V38 milliohm
ID at a 25 C case25 A per device
ID at a 25 C ambient17 A per device
Pulsed drain current75 A
Qg7.1 nC typical
RthJA26 K per watt typical, 35 maximum
RthJC4 K per watt typical, 5.5 maximum
Junction rangeMinus 55 to 150 C

The 35 per cent gap between the 10 V and the 4.5 V resistance is the same story as the rest of the 60 V band: the threshold is low enough that 4.5 V still works, but the drift region is not fully accumulated. On a 48 V rail the gate drive normally comes from a 10 to 12 V bootstrap, so the 28 milliohm figure applies and the 4.5 V row is only relevant on a 5 V referenced driver.

The ambient row of 17 A per device is the honest working current on a four square centimetre pad. At 17 A and 28 milliohm the loss is 8 W per device, which is more than the 3 by 3 body can carry for long; the real continuous figure in still air is 8 to 10 A per device, and the ambient row assumes an ideal board. A converter that needs 15 A per phase at 48 V in should use two of these in parallel or a 5 by 6 body.

48 V to 12 V conversion and telecom supplies

The natural circuit is a 48 V to 12 V synchronous buck or a half bridge converter at 200 to 400 kHz. In a buck, the low side carries 10 A for 75 per cent of the period at 28 milliohm, 2.1 W, and the high side carries the same current for 25 per cent, 0.7 W. The switching loss at 300 kHz with 7.1 nC and a 48 V rail is about 0.5 W, so the pair dissipates 3.3 W on one 3 by 3 pad, which is a 100 K rise and needs a plane.

In a two switch forward or an active clamp converter the same pair works with the body diodes doing the reset, and the 60 V rating covers the reflected voltage plus the leakage spike if the clamp is right. A 48 V input with a 1 to 1 turns ratio reflects 48 V, and a 60 V device holds it with 12 V of margin, which is tight but standard.

In a telecom brick the pair is used as the secondary rectifier on a 12 V output, where the voltage is low and the current is high. At 20 A and 28 milliohm the loss is 11 W, which is too much for the body, so the rectifier position uses three or four in parallel rather than one pair.

Drive and the shared pad

7.1 nC at 400 kHz is 2.8 mA of drive current per device, so a small driver is enough. The high side needs a bootstrap, and the bootstrap capacitor has to hold the charge through the on time at the maximum duty cycle. At a 90 per cent duty the high side is on for most of the period and the bootstrap is refreshed in the remaining 10 per cent, so the capacitor has to be sized for that refresh window rather than for the average.

The two devices share the lead frame, so the loss in one raises the other. In a buck that is acceptable because they conduct at different times, but in a two rail system where both are on continuously the pair runs twice as hot as one device would. The pad should give each device its own copper area and its own vias, and only the ground return is shared.

Where a board is being qualified against a 5 by 6 part of the same voltage, the pin to pin cross reference page covers which parameters have to match before the swap. On a 60 V part the thermal path is the one that differs most, because the 3 by 3 pad has a third of the area of a 5 by 6 and the same loss gives a much higher rise.

Buying this code

The vendor describes the silicon as trench, PWM optimized, 100 per cent gate resistance and unclamped inductive switching tested, with no automotive qualification on the page and no avalanche energy figure. A 60 V part in a switching converter that sees a long input cable needs that energy figure, so the data sheet has to be obtained before the part is released into a circuit with an unclamped inductive load.

Where the same pair is used across several 48 V products at different currents, the strategic sourcing page covers how the codes are grouped and how the second source is kept qualified across the group, which at this voltage is worth doing before the first shortage rather than after.

Two 60 V devices in one 3 by 3 body also mean the spacing inside the package between the split pads is small. On a board that carries a 48 V rail and a 5 V logic rail from the same part, the two drain pours have to be kept apart by the full 48 V spacing, and a shared thermal pour under the body is the usual way that spacing is lost. The pour looks reasonable on a thermal plot and it is a creepage fault on a safety review.

The sourcing side of this part is covered on the strategic sourcing. For a 60 V pair used across several 48 V products, that page covers how the codes are grouped and the second source kept qualified.

Questions we get on this code

Is 60 V enough for a 48 V rail? Yes with a clamped switching node. A 48 V rail floats at 57 V, so the margin is 3 V steady state and the ring has to be damped.

Can it be used at 25 A continuously? Only with the case held at 25 C. In still air the pair is good for 8 to 10 A per device, and the 17 A ambient row assumes an ideal board.

Why is the gate charge only 7.1 nC on a 60 V part? Because the silicon was tuned for PWM rather than for the lowest resistance. The trade shows up as 28 milliohm instead of 20.

Are both devices the same? Yes, independent and identical, unlike a half bridge part. Either can be used as the high side or the low side.