Contact Us

VBQF3316G

Brand: VBsemi
VBsemi VBQF3316G is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBQF3316G — Discrete & Power Semiconductors | Superb Automation

VBQF3316G

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBQF3316G from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBQF3316G: a half bridge in one 3 by 3 body

The VBQF3316G is a half bridge in the DFN 3 by 3 body: two 30 V N channel devices with the switch node brought out on a shared pad. Channel one is 20 milliohm at a 10 V gate and 26.5 milliohm at 4.5 V with 11 A of drain current and 3.5 nC of gate charge. Channel two is 9 milliohm at 10 V and 13.5 milliohm at 4.5 V with 28 A and 6.8 nC. The two are deliberately different: a small high side and a large low side, which is the mix a synchronous buck wants.

A half bridge in one package is not the same as two devices in one package. The drain of the high side and the source of the low side are the same node here, brought out on pin 9, so the switch node is short and the loop inductance between the two devices is set by the lead frame rather than by the board. That is worth 5 to 10 nH against two separate parts, and at 1 MHz with 10 A it is the difference between a 30 V ring and a 20 V ring.

The pinout also constrains the gate drive. Channel one sits between the input rail and the switch node, so its gate has to be driven from a bootstrap capacitor referenced to pin 9. Channel two sits between the switch node and ground, so its gate is driven from the controller's own supply. Both gates are on the same side of the body, which keeps the two gate loops short if the driver is placed there.

Key data for the VBQF3316G

ConfigurationHalf bridge, N channel pair
PackageDFN 3 by 3, switch node on pin 9
VDS30 V both devices
VGSPlus or minus 20 V
Vth1.7 V typical, both channels
RDS(on), channel one at 10 V20.0 milliohm
RDS(on), channel one at 4.5 V26.5 milliohm
RDS(on), channel two at 10 V9.0 milliohm
RDS(on), channel two at 4.5 V13.5 milliohm
ID, channel one11 A at a 25 C case
ID, channel two28 A at a 25 C case
Pulsed drain current30 A channel one, 40 A channel two
Qg3.5 nC channel one, 6.8 nC channel two
Body diode, channel one0.84 V typical, 1.2 V maximum

The ratio between the two channels is about two to one on resistance and two to one on gate charge, and that is a reasonable split for a converter with a 10 to 20 per cent duty cycle. The high side conducts for the on time and the low side for the rest, so a 12 V to 1.2 V rail has the high side on for 10 per cent of the period. Making the low side the larger device matches the loss to the duty cycle, and it is why a half bridge part is not just two identical devices in one package.

Thirty volts is enough for a 12 V rail with a clamp and for a 19 V notebook adapter rail, which is the range this part is aimed at. On a 24 V input the ring on the switch node can reach 30 V with a 20 nH loop, so the rating is tight and the snubber is not optional.

Where the half bridge goes

The first application is the core rail of a computing system, 12 V in, 1 to 1.8 V out, 15 to 25 A, 500 kHz to 1 MHz. The low side at 13.5 milliohm carries 20 A for 90 per cent of the period, 4.9 W, and the high side at 26.5 milliohm carries 20 A for 10 per cent, 1.1 W. The low side dominates and the thermal path has to be built around it, which is why the bigger die is on channel two.

The second application is point of load conversion on a board where the inductor sits next to the part, and the third is a synchronous buck that feeds a battery charger. In all three the switch node pad is the one to watch: it swings from ground to the input rail at the switching frequency, so any copper attached to it is a radiator. Keep it small and keep the gate drive return away from it.

A half bridge is also the easiest way to build a motor driver for a small brushless machine, one leg per phase. Three of these packages make a three phase inverter, and the switch node pads become the motor terminals. At 24 V and 5 A per phase the losses are modest, and the 30 V rating is the limit rather than the current.

Drive, dead time and the bootstrap

Channel one needs a bootstrap capacitor of at least ten times its gate charge, so 35 nC, which at a 5 V drop is 7 nF; 100 nF is the usual choice. The bootstrap diode has to be fast, because it charges in the low side on time, which at a 10 per cent duty cycle is short. A slow diode leaves the high side under driven and the 20 milliohm becomes 40.

Dead time is set by the driver and by the body diode of the device that is off. With 0.84 V of forward drop on channel one and 1.2 V maximum on channel two, the dead time loss at 20 A and 20 ns is 0.3 W, which is small but not free. Too little dead time is worse: shoot through at 30 V and 20 A is a destructive event, so the driver's dead time is set with margin and the loss is accepted.

Where the package has to be compared with two separate devices, the power management cross reference page covers what has to match before a swap. The internal switch node is the parameter with no equivalent: two separate parts need a copper connection that adds inductance, and a substitute in two packages will ring harder unless the snubber is re-tuned.

Buying this code

The vendor describes the pair as optimizing the high side and the low side for synchronous buck converters, with trench silicon, 100 per cent gate resistance and unclamped inductive switching tests, and no automotive qualification. The two channels are electrically independent except for the shared switch node, so an incoming test that traces only channel two will pass a part with a dead high side. Both channels have to be traced.

Where a build mixes this part with the dual independent pair of the same family, the incoming inspection plan page covers what is checked on receipt, from the reel label to a curve trace on both channels, and the two parts are easy to confuse because the bodies are the same size.

The bootstrap capacitor sits between the driver supply and the switch node, so its return is the switch node itself. That makes its loop the smallest high current loop on the board and the most sensitive to placement: 5 mm of trace at 1 MHz is about 30 nH, and the high side gate sees the drop across it as a slower turn on. Place the capacitor within 2 mm of the switch node pad and return the driver high side supply directly to it.

The sourcing side of this part is covered on the incoming inspection plan. For a half bridge body that can be confused with the dual independent pair, that page covers what is checked on receipt.

Questions we get on this code

Are the two channels really different? Yes. Channel two has roughly half the resistance and twice the current of channel one, which is why the pinout matters and why the two cannot be swapped.

Can the part be used as two independent switches? Not fully. The switch node is shared, so the high side source and the low side drain are one node. Two independent loads need the dual independent pair instead.

What is the 30 V rating good for? A 12 V rail and a 19 V adapter rail with a clamp. On a 24 V input the switch node ring has to be damped to stay under 30 V.

How is the part tested at incoming? Trace both channels. A single trace on the low side is the most common mistake with a half bridge body.