Contact Us

VBQF1402

Brand: VBsemi
VBsemi VBQF1402 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBQF1402 — Discrete & Power Semiconductors | Superb Automation

VBQF1402

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBQF1402 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBQF1402: a 40 V N channel at 2 milliohm in the 3 by 3 body

The VBQF1402 is a single N channel MOSFET in the DFN 3 by 3 body at 40 V drain to source, 2.0 milliohm at a 10 V gate and 2.4 milliohm at 4.5 V, 60 A of drain current marked package limited, 19.5 nC of total gate charge and 3240 pF of input capacitance. The vendor calls the silicon a fourth generation trench and states that the part is tuned for the lowest product of on resistance and output charge. That combination is what a synchronous buck or a synchronous rectifier wants, and it is a different brief from a load switch.

The 2 milliohm figure in a 3 by 3 body is the interesting part of the story. Ten years ago that resistance needed a 5 by 6 body and a much larger die. Two things made it possible: the die is now copper clip bonded rather than wire bonded, and the cell pitch in the trench has come down far enough that the channel resistance per square millimetre has halved. Both changes move the heat into the pad, which is why the junction to ambient resistance is published as 24 K per watt typical and 33 maximum, with 1.9 K per watt to the case.

Forty volts covers a 12 V rail with a load dump clamp, a 24 V rail with a TVS, and the input of a 48 V to 12 V converter when the switching node rings above the rail. It is the standard rating for telecom and industrial point of load converters, and the reason this part is listed for telecom point of load and bricks on the vendor page.

Key data for the VBQF1402

ConfigurationSingle N channel
PackageDFN 3 by 3, exposed pad
VDS40 V
VGSPlus 20 V, minus 16 V
RDS(on) at 10 V2.0 milliohm
RDS(on) at 4.5 V2.4 milliohm
ID at a 25 C case60 A, package limited
Qg19.5 nC typical
Qgs8.7 nC
Qoss at 20 V4.2 nC
Ciss3240 pF
Crss455 pF
Body diode0.74 V typical at a stated current, 1.1 V maximum
RthJA24 K per watt typical, 33 maximum
RthJC1.9 K per watt typical, 2.4 maximum

The gate charge is the number to watch. 19.5 nC at a 10 V drive means 19.5 mA of drive current at 1 MHz, and a controller with a 2 A peak driver can still switch this part fast, but the driver's own dissipation is no longer negligible. The 8.7 nC of gate to source charge is nearly half of the total, which is a consequence of the very low threshold voltage spread the part needs to reach 2 milliohm at a 10 V gate. Qoss of 4.2 nC and Crss of 455 pF set the switching loss in a buck, and they are the numbers that the low figure of merit is really about.

The body diode drop, 0.74 V typical and 1.1 V maximum, matters in a synchronous rectifier during the dead time and in a battery protection path. Every 10 ns of dead time at 20 A carries 0.2 microcoulomb through that diode, which at 500 kHz is a continuous 0.1 A of diode current and 74 mW of loss. That is why the dead time is trimmed on the controller rather than left at the driver default.

Synchronous buck and synchronous rectification

On the low side of a 12 V to 1 V converter at 500 kHz, this part carries the inductor current for two thirds of the period. At 30 A RMS the conduction loss is 1.8 W at 25 C and about 2.7 W hot, and the switching loss is set by Qoss and the reverse recovery of the body diode. The 3 by 3 pad into four square centimetres of copper holds that at a 60 to 80 K rise, which is why this body is used at 20 to 30 A per phase and not at 60 A.

On the high side the same part sees the full input voltage when it is off and carries the peak current for the on time. The drive has to come from a bootstrap or a charge pump referenced to the switching node, and the 20 V gate limit is comfortable on a 12 V rail but tight on a 24 V rail, where a zener across gate and source is normally fitted. On a 48 V input the part belongs only on the low side.

For a battery protection or an ORing path the body diode direction decides the circuit. With the source towards the load, the diode conducts from load to battery when the battery is missing, which is what an ORing controller uses; with the drain towards the load, the diode blocks and the part protects against a reversed cell. The difference is one rotation of the part on the board and it is worth settling before the land pattern is released.

Loss, drive and the thermal path

At 2 milliohm the conduction loss at 20 A is 0.8 W, at 40 A it is 3.2 W and at 60 A it is 7.2 W. Hot, the resistance rises by about 40 per cent from 25 to 125 C, so the 40 A figure becomes 4.5 W. The junction to case resistance of 1.9 K per watt means the die is 3 to 9 K above the pad at those currents, and the rest of the rise is the board. A pad with six 0.3 mm vias into an inner plane takes the junction to ambient figure from 33 to nearer 20 K per watt, which is the difference between 30 A and 40 A of continuous current.

The gate loop has to be short. With 455 pF of reverse transfer capacitance the part switches in 10 to 20 ns with a 2 A driver, and every nanohenry in the source connection turns that into ringing on the gate. A separate source return to the driver, or a kelvin connection at the pad, is the usual remedy and it costs nothing on the board.

Where a substitute has to be proposed because the original code is not available, the pin to pin cross reference page covers which parameters have to match, including the threshold, the gate charge and the Qoss that decide whether the existing drive and dead time still work. A part with the same resistance and half the gate charge is not automatically better: the switching loss moves, the dead time changes and the loop compensation may need attention.

Sourcing notes on this code

The vendor states that the part is 100 per cent gate resistance and unclamped inductive switching tested, and that the silicon is a fourth generation trench. Those are process statements rather than qualification documents, and the page carries no AEC-Q101 claim, so a vehicle build needs a separate qualification record. The 40 V rating is above a 35 V load dump clamp only in the clamped system, and an unclamped pulse heats the die as well as stressing it.

Where this code is carried on a production BOM at 20 to 40 A per phase, the BOM consolidation page covers how a family of parts across several builds is merged without losing a qualification, which is usually the cheaper answer than a second source on every line.

The sourcing side of this part is covered on the BOM consolidation. For a part carried across several builds at 20 to 40 A per phase, that page covers how the family is merged without losing a qualification.

Questions we get on this code

Is 60 A a working current? No. It is package limited with the case at 25 C. On a board with the pad tied to four square centimetres of copper, 25 to 35 A continuous is the honest figure, and the SOA curve is what to read for a pulse.

Why is the gate source limit asymmetric? The vendor prints plus 20 V and minus 16 V. A bootstrap drive on a ringing switching node can pull the gate below the source, so the negative limit is the one to protect with a small resistor or a clamp.

Can it replace a 5 by 6 part with the same resistance? Electrically often yes, thermally no. The 3 by 3 pad is a third of the area of a 5 by 6 pad, so the same loss gives a higher rise unless the copper is redistributed.

What is Qoss used for? It sets the energy stored in the output capacitance that has to be dissipated each cycle in a hard switched converter. At 4.2 nC and a 24 V rail the stored energy is around 50 microjoule, which at 500 kHz is 25 mW, small but not zero in a 1 W budget.