VBQF1102N
Product Specifications
VBQF1102N
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBQF1102N from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBQF1102N: a 100 V N channel in a 3 by 3 body
The VBQF1102N is a single N channel MOSFET in the DFN8 3 by 3 body, printed at 100 V drain to source, plus or minus 20 V on the gate, a 1.8 V threshold, 35.5 A of drain current and 17 milliohm at a 10 V gate. The vendor table gives no 4.5 V figure, which is the first thing to notice: this part is specified for a 10 V drive and its behaviour at a lower gate voltage is not published.
One hundred volts in a 3 by 3 body is a dense part. The die is a large fraction of the package footprint and the pad is the whole underside, which is how 17 milliohm is reached at this voltage. It also means the thermal path is good and the solder joint has to be void free, because the only path out of the die is straight down through that pad.
This is the part used where a 48 V rail has to be switched with margin, or where an 80 V transient has to be held off, and the board cannot afford a 5 by 6 land pattern. Telecom line cards, 48 V PoE front ends and 72 V battery tools are the three places it turns up.
Key data for the VBQF1102N
| Configuration | Single N channel |
| Package | DFN8 3 by 3, exposed pad |
| VDS | 100 V |
| VGS | Plus or minus 20 V |
| Vth | 1.8 V typical |
| ID | 35.5 A at a 25 C case |
| RDS(on) at 10 V | 17 milliohm |
| RDS(on) at 4.5 V | Not published by the vendor |
| Structure | Trench |
| Conduction at 5 A | 0.43 W |
| Conduction at 10 A | 1.7 W |
| Conduction at 20 A | 6.8 W |
| Conduction at 35.5 A | 21.4 W |
A 100 V die in a 3 by 3 body has very little silicon margin around it. The edge termination of a 100 V trench die takes several tens of microns, and at this die size that is a noticeable fraction of the area, which is why the resistance rises so steeply with voltage in this family compared with the 5 by 6 parts. It also means the part is less tolerant of a solder void under the pad: the heat has nowhere to spread sideways inside the package, so a void covering a third of the pad raises the junction temperature by 30 to 40 per cent rather than by a few degrees.
Where a 100 V part in a small body is used
The first case is the primary switch in a 48 V to 12 V converter. The switch node sees the 48 V rail plus the leakage spike, which on a well clamped board reaches 80 to 90 V, so a 100 V part holds a margin of 1.1 to 1.25. At 10 A the conduction loss is 1.7 W and the switching loss is set by the gate charge and the frequency.
The second case is a hot swap or an inrush limiter on a 48 V backplane, where the part is in the linear region for a few milliseconds while the bulk capacitance charges. That is a safe operating area event rather than a resistance event, and the datasheet curves, not the resistance table, decide whether the part survives it.
The third case is a 72 V battery tool or a 60 V e-bike controller, where the rail is 84 V at full charge and the switch has to hold 100 V with the motor inductance clamped. Those boards are tight, which is why the 3 by 3 body is chosen over a 5 by 6 even at some thermal cost.
Drive, and the missing 4.5 V column
The absence of a 4.5 V resistance figure is a deliberate choice by the vendor, not an omission: at 4.5 V a 100 V trench part is only partly enhanced and the resistance can be two to three times the 10 V value. A circuit that drives this part from a 5 V logic pin therefore has to size the loss from a bench measurement or from the transfer curves, not from the table.
In practice these parts are driven from a 10 to 12 V gate drive, either a dedicated driver or a bootstrap supply, and the 1.8 V threshold means the part turns on early and the driver has to sink the gate quickly enough to keep the switching loss down. A 10 ohm gate resistor is a reasonable starting point at 100 to 300 kHz.
Thermal behaviour in a 3 by 3
At 10 A the loss is 1.7 W and at 20 A it is 6.8 W from 17 milliohm. A 3 by 3 pad on four square centimetres of copper is about 35 to 45 K per watt, which puts 10 A at a 60 to 75 K rise and 20 A at 240 to 305 K, so 20 A is not a continuous point in still air.
The 35.5 A headline is a die figure at a 25 C case, and in a 3 by 3 the case is the pad. Reaching it needs a metal core board or a heatsink under the part. The honest continuous current on a normal FR-4 board is 8 to 12 A, and the pad copper area matters more than the copper thickness at this size.
Where this part is being compared against a 5 by 6 alternative, the pin to pin cross reference page covers which parameters have to match before the smaller body is accepted, starting with the pad geometry and the thermal path rather than the resistance.
At 100 V the switching loss is dominated by the drain to source capacitance and by the reverse recovery of whatever diode sits in the loop. A snubber across the switch, a resistor and a capacitor in series, trades a little conduction loss for a large reduction in the peak at turn off, and on a 3 by 3 part with a short thermal path that trade is usually worth making. The alternative is to slow the turn on with the gate resistor, which moves the loss into the channel and heats the die instead of the snubber.
The pad is the drain and also the heatsink, so the copper under the part carries the switch node voltage in a converter and the full input in a high side switch. On a 48 V rail that means the pour under the pad sits at 48 V when the part is off, and any signal routed through or under that copper picks up the switching node. Keeping the return path and the gate loop out from under the pad costs nothing and removes a common source of noise in these small bodies.
The sourcing side of this part is covered on the how to verify a drop in replacement. For a 100 V part moving from a 5 by 6 body to a 3 by 3, that page covers the bench checks before the change is signed off.
Questions we get on this code
Can it be driven from 5 V? It will switch, but the vendor publishes no resistance at 4.5 V, so the loss has to be measured or read from the curves. Plan for two to three times the 10 V figure.
Is 100 V enough for a 48 V rail? Yes with a clamp that holds the spike below 90 V. Without a clamp the leakage inductance of the board arrangement decides, and 100 V can be exceeded on a fast turn off.
How much copper does the pad need? Four square centimetres of two ounce copper is the working figure for 10 A. Below that the current has to come down or the air has to move.
Is the body diode fast enough for a synchronous use? The vendor publishes no reverse recovery figure, so it should not be used as a synchronous rectifier without characterisation.