Contact Us

VBQA3102N

Brand: VBsemi
VBsemi VBQA3102N is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBQA3102N — Discrete & Power Semiconductors | Superb Automation

VBQA3102N

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBQA3102N from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBQA3102N: two 100 V N channels in one DFN 5 by 6

The VBQA3102N is a dual N channel MOSFET in the DFN 5 by 6 body, printed at 100 V drain to source and plus or minus 20 V on the gate. Each leg carries 18 milliohm at a 10 V gate and 22 milliohm at 4.5 V, with 35 A at a 25 C case and 20 A once the case reaches 100 C. The two legs sit on separate drain pads, with their own gate and source pins, so they can be wired as two independent switches or as the high side and low side of a small half bridge. Bought as a pair in one body, the part saves board area and one reel position on a bill of materials that already carries dozens of line items, and it keeps the two switches thermally tied so neither runs away from the other.

The sheet names a 175 C junction limit, a 110 mJ single pulse avalanche rating into 0.1 mH, and 136 W of dissipation at a 25 C case against 3 W at a 25 C ambient. Those three numbers decide most of the practical use. The 35 A headline belongs to a 25 C case with the drain pad soldered to a large copper area, and the same die in still air is a fraction of that. Buyers who read only the front page and put the part on a narrow trace come back with a hot board and a short life, which is why the ambient row is the one we quote first.

The ratings a buyer checks first

Drain to source voltage100 V
Gate to source voltageplus or minus 20 V
On resistance at 10 V gate18 milliohm at 20 A
On resistance at 4.5 V gate22 milliohm at 12 A
Continuous drain current35 A at 25 C case, 20 A at 100 C case
Pulsed drain current105 A
Continuous source current, diode76 A
Single pulse avalanche energy110 mJ into 0.1 mH
Avalanche current82 A
Power dissipation136 W at 25 C case, 3 W at 25 C ambient
Junction to case0.85 C per watt typical, 1.1 maximum
Gate threshold voltage1 V minimum, 2 V typical, 3 V maximum
Total gate charge70 nC typical, 89 nC maximum
Input capacitance3900 pF
Body diode forward voltage1.0 V typical, 1.5 V maximum at 20 A

What the electrical table adds to the summary

The threshold window is 1 V minimum, 2 V typical and 3 V maximum at 250 microamp. A 4.5 V gate drive therefore turns the part on with useful margin even on a worst case die, and a 10 V drive leaves the threshold window far behind. The gate charge of 70 nC typical and 89 nC maximum, with 23 nC of gate to drain charge, is a moderate load for a driver in a small package: at 200 kHz the drive loss per leg stays under 20 milliwatt with a 5 V rail, so a dual driver in a SOT-23 body is enough. Input capacitance is 3900 pF and reverse transfer 225 pF, which is a quiet die for its area and one that does not need a large gate resistor to stay stable.

Switching times are quoted at 100 V with a 0.6 ohm load and a 2.5 ohm gate resistor: 21 ns turn on delay, 15 ns rise, 35 ns turn off delay and 20 ns fall. Those are typical figures with a resistor that is deliberately large, so a real board with a 1 ohm gate resistor switches faster and rings more. The leakage rows move a long way with temperature: 1 microamp at 25 C, 50 microamp at 125 C and 250 microamp at 175 C, which matters in a battery path that has to sit idle for months with the switch off.

The body diode is the row that decides whether the part can be the low side of a bridge. Forward voltage is 1.0 V typical and 1.5 V maximum at 20 A, and reverse recovery takes 135 ns at a 100 A per microsecond slope. In a hard switched half bridge at 100 kHz that recovery is a real loss in the opposite leg, and it has to be counted in the loss budget rather than discovered on the thermal camera. For a synchronous rectifier at 48 V it is acceptable; for a converter running above 200 kHz the diode loss becomes the reason to look at a part with a faster body diode.

Where the two legs earn their space

The natural home is a 48 V or 60 V rail. Telecom line cards use one leg as an input disconnect and the other as a load switch, so the card can be pulled without arcing the connector, and the 100 V rating covers the inductive kick of a long backplane trace. PoE powered devices use the pair as a pass element and a return disconnect, and the 110 mJ avalanche rating absorbs the cable unplug event without an external clamp in most builds. Battery powered tools with a 72 V pack use the two legs as a half bridge for a small motor, where the DFN body keeps the loop short and the gate charge low enough for a driver running from the pack.

Two independent loads on one rail is the other common pattern: a heater and a fan, or a lamp and a solenoid, each on its own leg with its own gate signal. The two legs share one thermal pad, which is convenient in a dense product and a trap in a hot one, because the dissipation of both legs adds in the same junction. A build that runs one leg at 3 A continuously and the other in short bursts is fine; a build that runs both at 6 A continuously needs the copper area and the ambient to be checked against the 3 W figure rather than the 136 W one.

Sourcing notes and the second source question

The DFN 5 by 6 dual N channel pin map is close to a de facto standard across several vendors, but close is not equal. Drain pad routing, gate resistance and threshold windows differ, and a part that drops in physically can still fail a conducted emissions limit or a cold start test. Our pin to pin cross reference starts from the pad geometry and the gate charge, not from the headline voltage and current. When a customer sends a competitor code, the four rows we compare first are on resistance at 4.5 V, threshold maximum, total gate charge and avalanche energy.

For a replacement that has to be proven on the customer board rather than on paper, the checklist in how to verify a drop in replacement covers the tests that catch the failures we see most: gate ringing at the new gate resistance, reverse recovery in the low side body diode, and thermal margin at the case temperature the product actually reaches. We supply this code with the matching driver and gate resistor from the same bill of materials, and where the quantity allows we kit both legs as one reel position so the line does not stop for a second part number.

Questions we answer before a reel is booked

Buyers ask whether the 35 A figure can be used at 25 C ambient. It cannot. It is a case temperature rating, and the same die with 3 W of dissipation in still air carries roughly 2 A before the junction reaches 150 C. The second question is whether both legs can run at full current at once. They can electrically, but the package shares one thermal path, so the two loads share one budget and the answer depends on the duty cycle of each leg.

We are also asked about the 76 A diode rating, which is higher than the 35 A channel rating because the diode is a wide path in this die and the package lets it use the full pad. A synchronous stage that relies on the diode during a long dead time can use that number, but only with the junction starting cold. On avalanche, the 110 mJ figure is a single pulse into 0.1 mH at 25 C, and repeated events derate with temperature and repetition rate, so a clamp is still cheaper than a warranty claim.

Availability is quoted per reel with the date code printed on the label, and we hold the incoming inspection record for each lot, including an on resistance sample at 4.5 V. If a build needs a specific date code window for a product that is already qualified, that has to be booked before the order is placed, because mixed date codes in one shipment are the usual reason a line stops for a re qualification it did not plan.