Contact Us

VBQA2303

Brand: VBsemi
VBsemi VBQA2303 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBQA2303 — Discrete & Power Semiconductors | Superb Automation

VBQA2303

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBQA2303 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBQA2303: a 30 V P channel at 3 milliohm and 100 A

The VBQA2303 is a single P channel MOSFET in the DFN8 5 by 6 body, printed at minus 30 V drain to source, plus or minus 20 V on the gate, a minus 3 V threshold, minus 100 A of drain current, 5 milliohm at a 4.5 V gate and 3 milliohm at a 10 V gate. The structure is trench. It is the power path part of the band: the switch that sits between a battery and a load on a 12 or 24 V system and has to carry the whole load current with almost no loss.

A P channel at 3 milliohm is a large die. Hole mobility being a third of electron mobility, this die is roughly three times the area of a 1 milliohm N channel of the same voltage, which is why the current rating stops at 100 A where an N channel in the same footprint reaches 150 A or more. The advantage is that the switch can sit in the positive line with the gate driven from ground and no charge pump.

This part is used for reverse polarity protection, power path selection between a battery and an adapter, and load switching on a 12 to 24 V rail. In all three the current is 20 to 60 A, the switch is on for minutes or hours at a time, and the loss at 3 milliohm is small enough that the part does not need a heatsink beyond its own pad.

Key data for the VBQA2303

ConfigurationSingle P channel
PackageDFN8 5 by 6, exposed pad on the drain
VDSMinus 30 V
VGSPlus or minus 20 V
VthMinus 3 V typical
IDMinus 100 A at a 25 C case
RDS(on) at 4.5 V5 milliohm
RDS(on) at 10 V3 milliohm
StructureTrench
Conduction at 10 A0.3 W
Conduction at 30 A2.7 W
Conduction at 60 A10.8 W
Conduction at 100 A30 W

Reverse polarity protection

The classic circuit puts the P channel in the positive line with the source towards the battery and the drain towards the load, the gate held to ground by a resistor. When the battery is connected the right way round the body diode conducts first, the source rises, the gate is 12 V below the source and the part turns on. When the battery is reversed the gate is above the source and the part stays off, and the body diode blocks.

The catch is that the body diode carries the load until the channel turns on, so the input capacitor has to hold the load for the few hundred microseconds the gate takes to charge. With a 10 k gate resistor and 100 nC of gate charge the turn on is 100 microseconds, and a 5 A load during that time is 0.5 millicoulomb, which a 100 microfarad capacitor supplies with a 5 V dip. A larger gate resistor slows the turn on and deepens that dip.

The second catch is the voltage rating. A 30 V part on a 24 V system with a 29.4 V full pack has 0.6 V of margin, and a load dump or a spike through the input takes it out. Most 24 V systems use a 40 V part here, and this 30 V part is used on a 12 V rail where the margin is 2.3.

Power path and load switching

In a power path the part selects between a battery and an adapter. Two P channels back to back, or one P channel and one Schottky, share the load, and the switch that is on carries the whole current. At 30 A and 3 milliohm the loss is 2.7 W, which a 5 by 6 pad on six square centimetres of copper passes with 50 to 70 K of rise. That is warm but inside the limit, and it is the reason this part does not need a sink.

Load switching is the same circuit with a slower gate. A 10 k gate resistor gives a 100 microsecond turn on, which is what a 100 microfarad load wants, and a 1 k resistor gives a 10 microsecond turn on, which is what a hot swap of a small board wants. Neither is a soft start: the part is either off or in its linear region for the transition, and the energy in that transition is what the safe operating area has to cover.

The body diode is the part of the datasheet that gets forgotten. In a load switch the diode is forward biased when the output is above the input, which happens when the load is inductive or when a second source back feeds. A P channel with the drain towards the load puts the diode in the blocking direction for that case, so the orientation matters as much as the part.

Where several 30 V P channel codes are on one bill of materials, the BOM consolidation page covers how the class is merged without losing a qualification, and the power management cross reference page covers which parameters have to line up before one code is used for two positions.

Gate drive on a 30 V P channel

The gate of a 30 V P channel in a 12 V system is pulled to ground to turn on, so the gate to source voltage is 12 to 14 V when the battery is charging. That is inside the 20 V limit but with only 6 V of headroom, and a spike on the battery couples through the gate to source capacitance. A 15 V zener across gate and source plus a 100 ohm series resistor is the minimum protection on an automotive or a battery fed rail.

On a 24 V system the same circuit puts 29 V across the gate, which is past the limit, so the gate has to be driven from a divider or a small N channel that clamps the gate at 10 V below the source. That is the point where the simplicity argument for a P channel starts to weaken against an N channel with a charge pump.

The turn on time is set by the gate resistor and the gate charge. A 10 k resistor against 100 nC gives 100 microseconds, which is a soft start for a capacitive load and no protection at all for a short. A 1 k resistor gives 10 microseconds, which is fast enough to limit the energy in a fault and slow enough to keep the drain spike inside 30 V. Between 1 k and 4.7 k is the working range for most 30 V power path circuits.

The sourcing side of this part is covered on the BOM consolidation. For a 30 V power path part, that page covers how the class is merged without losing a qualification.

Questions we get on this code

Is 3 milliohm a maximum? The table prints one value, so treat it as nominal. A production lot sits 10 to 20 percent above it, and at 60 A that is 1 to 2 W of extra loss.

Does the part survive a reversed battery? Yes, that is what the circuit is for, as long as the gate is referenced to the source and the 20 V gate limit is respected. With a 24 V pack the gate to source reaches 29 V and the part does not survive without a clamp.

Can it be used in the negative line instead? Yes, with the source towards the load and the gate driven from the battery positive. The circuit is the mirror image and the body diode orientation reverses with it.

What limits the continuous current? The pad, not the die. At 60 A the die makes 10.8 W and the pad on six square centimetres passes it. At 100 A the die makes 30 W and the pad needs eight to ten square centimetres and air movement.