Contact Us

VBQA165R05S

Brand: VBsemi
VBsemi VBQA165R05S is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBQA165R05S — Discrete & Power Semiconductors | Superb Automation

VBQA165R05S

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBQA165R05S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBQA165R05S: 650 V and 5 A in a DFN 5 by 6 at 1 ohm

The VBQA165R05S is a single N channel MOSFET in the DFN8 5 by 6 body, printed at 650 V drain to source, plus or minus 30 V on the gate, a 3.5 V threshold, 5 A of drain current and 1000 milliohm at a 10 V gate. The structure is SJ_Multi-EPI, a multi epitaxial superjunction die, which is a unusual thing to find in a leadless package at this voltage.

The point of this part is the package, not the current. A 650 V die in a 5 by 6 package with a 30 square millimetre pad puts the thermal path into the board copper instead of a tab and a screw. That removes the insulating pad, the clip and the hand assembly, and it lets a 5 W dissipation be handled by the same copper that carries the current. For a 30 to 100 W auxiliary supply on a 400 V bus this is often cheaper than a TO220 with a sink.

The 1 ohm figure sounds high against the low voltage parts in this band and it is the correct number for the voltage. A 650 V die that carried 5 A at 100 milliohm would need ten times the area, and the package could not pass the loss at that area. The 1 ohm figure is what makes a 5 A, 650 V part fit in 30 square millimetres.

Key data for the VBQA165R05S

ConfigurationSingle N channel
PackageDFN8 5 by 6, exposed pad on the drain
VDS650 V
VGSPlus or minus 30 V
Vth3.5 V typical
ID5 A at a 25 C case
RDS(on) at 10 V1000 milliohm
StructureMulti epitaxial superjunction
Conduction at 0.5 A0.25 W
Conduction at 1 A1 W
Conduction at 2 A4 W
Conduction at 3 A9 W

Where a 650 V leadless part belongs

An auxiliary supply on a 400 V bus, a PFC stage under 100 W, a snubber or clamp switch, and a start up path that has to be on for a few milliseconds are the four places it lands. In each case the current is 0.3 to 2 A and the voltage is 400 to 500 V, and the loss at 1 A is 1 W, which a 5 by 6 pad on four square centimetres of copper passes with 25 to 35 K of rise.

The alternative is a TO220 or a DPAK. A DPAK has a tab that can take a small clip, and a TO220 has a tab for a screw. Both are bigger than the 5 by 6 and both need a wave solder or a selective solder step, which the 5 by 6 does not. On a board that is already reflow only and has 30 other leadless parts, the 5 by 6 removes a process step.

The counter argument is the creepage. A 650 V part in a leadless package has drain and source pads 0.5 to 1 mm apart, and the pad is on the surface where a flux residue can bridge it. A conformal coat and a proper cleaning step are not optional at this voltage. Where the board has to run in a humid environment, a through hole body with a 4 mm pin spacing is the safer choice and the package saving is not worth the field return.

Losses and the copper pad

At 1 ohm the die makes 0.25 W at 0.5 A, 1 W at 1 A, 4 W at 2 A and 9 W at 3 A. On a hot die the resistance roughly doubles by 125 C, so 2 A becomes 8 W and 1 A becomes 2 W. An auxiliary supply that draws 1.5 A from a 400 V bus is running this part at 5 to 6 W with the junction at 110 to 130 C on a modest pad.

A 5 by 6 pad soldered to four square centimetres of copper has a junction to ambient resistance of 25 to 35 K per watt. At 4 W that is 100 to 140 K of rise, which on a 40 C internal ambient is a junction at 140 to 180 C. The same part on eight square centimetres of copper with four vias is 15 to 20 K per watt, which is 60 to 80 K and a junction at 100 to 120 C. The pad area, not the part, decides whether the supply runs.

The switching loss at 650 V is small in absolute terms because the current is small. At 65 kHz and 1 A with a 400 V swing the crossover is 0.6 to 1 W, and at 200 kHz it is 2 to 3 W. Below 100 kHz the conduction term dominates and the calculation is easy. Above 200 kHz the capacitance matters and the part should be chosen on output charge rather than resistance.

The order code needs a second look

The vendor page for this part carries a body text that names the model as VBFB165R05S, a TO3P part number, while the page title and the parameter table carry VBQA165R05S. The table also prints 1000 milliohm where the descriptive text prints 950. Neither difference changes the part that ships if the page is right about the package, but it is the sort of thing to confirm against a supplier confirmation before a purchase order is released, especially where the part is going onto a qualification build.

Two readings are possible. The page may be a copy of the TO3P page with the package and the title edited, in which case the electrical numbers are the TO3P die and the leadless body carries the same silicon. Or the page may be a new part with a copied description, in which case the numbers in the table are the ones to trust. The only way to settle it is a vendor confirmation with the part marking, and the marking on a 5 by 6 body includes the code and the lot.

This is the class of problem the how to verify a drop in replacement page is written for, and where the part is going into a build that has to hold for years, the supplier quality audit page covers what is checked at the source before the first lot is released.

The sourcing side of this part is covered on the how to verify a drop in replacement. For a 650 V part in a leadless body, that page covers the bench checks before a swap is signed off.

Questions we get on this code

Is the 1000 milliohm figure at 10 V? Yes, the table gives it at a 10 V gate. At a 4.5 V gate the resistance is higher, so a 5 V driver should not be assumed to reach the printed number.

Can it carry 5 A continuously? No. At 5 A the die makes 25 W, which no 5 by 6 pad passes without a metal core board. The working current is 1 to 2 A, and 3 A only with a large pad and air movement.

Does the pad need isolation? No, the pad is the drain and it is at the switch node, so the copper under it carries the switching voltage. That copper has to be kept away from anything sensitive, including the gate trace.

What is the creepage at 650 V? The pad spacing is under 1 mm, so the board needs a conformal coat or a potted enclosure. This is the main reason a through hole part is still chosen at this voltage.