Contact Us

VBQA1303

Brand: VBsemi
VBsemi VBQA1303 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBQA1303 — Discrete & Power Semiconductors | Superb Automation

VBQA1303

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBQA1303 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBQA1303: 30 V and 120 A in a DFN 5 by 6 at 3 milliohm

The VBQA1303 is a single N channel MOSFET in the DFN8 5 by 6 body, printed at 30 V drain to source, plus or minus 20 V on the gate, a 1.7 V threshold, 120 A of drain current, 5 milliohm at a 4.5 V gate and 3 milliohm at a 10 V gate. The structure is trench. It is the highest current member of this package band and the part that gets bought when a 12 or 24 V rail has to switch 60 to 100 A on a board with no room for a through hole body.

The DFN 5 by 6 is a leadless package with a large exposed pad that is the drain. The pad is soldered to the board copper, and the copper is the heatsink. That changes the thermal calculation completely: the junction to case number is small, the junction to ambient number depends on how much copper the pad sits on and how many vias run under it, and the same part can run 40 K cooler or hotter depending on the footprint.

Three milliohm at a 10 V gate is a die limited figure. At the pins the board sees 3.4 to 4.2 milliohm, because the lead frame, the source clip and the solder joint each add a fraction. A 100 A stage that calculates 30 W from 3 milliohm and measures 42 W is not seeing a bad lot, it is seeing the interconnection.

Key data for the VBQA1303

ConfigurationSingle N channel
PackageDFN8 5 by 6, exposed pad on the drain
VDS30 V
VGSPlus or minus 20 V
Vth1.7 V typical
ID120 A at a 25 C case
RDS(on) at 4.5 V5 milliohm
RDS(on) at 10 V3 milliohm
StructureTrench
Conduction at 20 A1.2 W
Conduction at 50 A7.5 W
Conduction at 80 A19.2 W
Conduction at 120 A43.2 W

The 30 V class on a 24 V rail

A 24 V system runs from 18 V empty to 29.4 V on a full six cell lithium pack, and a 30 V part has 0.6 V of margin against the pack at rest. That sounds impossible and it is why the 30 V class on a 24 V rail always comes with a clamp, a soft start and a short loop. On a regulated 24 V rail with no battery the margin is 6 V and the part is comfortable. On a battery fed rail the 40 V class is the safer pick, and the 30 V part is used only where the pack cannot exceed 26 V under any condition.

A 12 V rail is the natural home. A 12 V battery at 14.4 V charging and a 19 V adapter input both sit well inside 30 V, and the load currents in a server, a network switch or a motor drive are 40 to 100 A. At 3 milliohm the part carries 60 A at 10.8 W, which a 5 by 6 pad on eight square centimetres of copper can pass with 40 to 55 K of rise.

The third use is a low side switch on a 20 V DC bus, where the part is either fully on or fully off and the only spec that matters is the on resistance and the gate charge. Those stages run 90 A continuous and treat the part as a contactor.

The thermal path through the pad

At 3 milliohm the die makes 1.2 W at 20 A, 7.5 W at 50 A, 19.2 W at 80 A and 43.2 W at the printed 120 A. Hot, the resistance is 4.5 to 5.5 milliohm at 125 C, so the 50 A figure becomes 11 to 14 W.

The 5 by 6 pad is about 30 square millimetres. Soldered to a copper pour of the same size on a two layer board the junction to ambient resistance is 45 to 60 K per watt; on an eight layer board with twelve vias under the pad it is 20 to 30 K per watt. At 19.2 W those two cases are 60 to 115 K of rise against 20 to 30 K, and that difference decides whether 80 A is a working number or a test bench number.

The via array is the part of the footprint that gets copied from a reference footprint without being checked. Twelve vias of 0.3 mm drill in a 3 by 4 grid give a thermal resistance of about 8 to 12 K per watt from the pad to the inner copper, and they also carry the source current. A footprint with four vias and a 0.5 mm annular ring is a 30 W limit at 80 A, not a 19 W one.

Driving a 3 milliohm die at 100 A

The gate charge of a die this size is 80 to 120 nC. At 300 kHz that is 24 to 36 mA of average gate current at 10 V, and the peak needed to finish the transition in 20 ns is 4 to 6 A. A controller with a 1 A driver turns the part on in 100 ns, and during that time the die is in its linear region with 24 V across it and 50 A through it, which is a 600 W pulse.

A 1.7 V threshold means the part is fully enhanced at 4.5 V and the 10 V figure is only 40 percent better than the 4.5 V one. That is a small difference for the trouble a 10 V rail causes on a 12 V board, and it is the reason many 30 V stages run a 4.5 V drive and accept 5 milliohm.

Where a synchronous stage uses two of these, the dead time matters. A 30 V die has a body diode with a 0.7 to 0.9 V drop at 50 A, so 100 ns of dead time at 200 kHz is a 0.7 W average loss in the diode plus the recovery charge on the opposing switch. Too little dead time is worse: a shoot through of 20 ns at 24 V is 200 W of pulse.

Where the part has to be swapped for a second source, the pin to pin cross reference page covers which parameters have to match before a leadless part is signed off, and the how to verify a drop in replacement page covers the bench checks that catch a footprint that fits but a thermal path that does not.

The sourcing side of this part is covered on the pin to pin cross reference. For a leadless part that has to be second sourced, that page covers which parameters have to match.

Questions we get on this code

Is 120 A a working current? Only with a heavy copper pad and air movement. The realistic continuous figures are 45 to 60 A on a two layer board and 75 to 90 A on a multilayer board with a full via array.

Does 3 milliohm include the package? No. It is a die figure at a 10 V gate. The board sees 3.4 to 4.2 milliohm at the pads, and the loss calculation should use the higher number.

Can it be used on a 24 V battery? Only with a clamp and a pack that cannot exceed 26 V. A six cell lithium pack at 29.4 V leaves 0.6 V of margin, and one spike takes the part out.

How is the date code read on a leadless part? It is laser marked on the top surface with the lot and the date, and it is small. A reel that arrives without a readable marking is material to hold at goods inwards rather than to release.