Contact Us

VBQA1102N

Brand: VBsemi
VBsemi VBQA1102N is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBQA1102N — Discrete & Power Semiconductors | Superb Automation

VBQA1102N

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBQA1102N from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBQA1102N: 100 V and 17 milliohm in a DFN 5 by 6 body with a 3 V threshold window

The VBQA1102N is a 100 V N channel trench MOSFET in the DFN 5 by 6 body with an exposed drain pad. The summary prints 100 V, 0.017 ohm at a 10 V gate and a 30 A continuous rating at a 25 C case, and the sheet adds a 175 C junction limit, a 100 per cent gate resistance test and a low thermal resistance package as the reason to choose it over a leaded part.

The intended use on the sheet is isolated DC to DC converters, which is a narrow list compared with a general purpose switch, and it explains the ratings. A 100 V part in a 5 by 6 body at 17 milliohm is a primary side or secondary side switch in a converter running from a 48 V rail, where the drain sees the reflected output plus the leakage spike and 100 V gives room for both.

The rating table has four current rows rather than one, and the spread is what decides whether the part fits. Thirty amps applies with the case held at 25 C, 19 A at a 70 C case, 10 A on a one inch square board in 25 C air and 8.5 A in 70 C air. The last two are the ones a converter without a heatsink actually lives at, and they are one third of the headline.

Threshold voltage is the second thing to check before anything else. The window is 3.0 V minimum and 5.0 V maximum, and the on resistance is specified at 10 V and at 7.5 V with nothing at 4.5 V. A circuit that drives this part from a 5 V logic rail is outside what the sheet guarantees, and the 7.5 V row at 0.020 ohm is the closest published operating point.

The parameter table in full

Drain to source voltage100 V
Gate to source voltage, continuousplus or minus 20 V
Continuous drain current, case at 25 C30 A
Continuous drain current, case at 70 C19 A
Continuous drain current, board at 25 C and 70 C10 A and 8.5 A
Pulsed drain current at 100 microsecond75 A
Continuous source drain diode current, case at 25 C56 A
Single pulse avalanche current, 0.1 mH20 A
Single pulse avalanche energy20 mJ
Maximum power dissipation, case at 25 and 70 C60 and 40 W
Maximum power dissipation, board at 25 and 70 C5 and 3.2 W
Junction to ambient, 10 s, typical and maximum20 and 25 C per watt
Junction to case, typical and maximum1.6 and 2.0 C per watt
Breakdown voltage at 250 microamp100 V
Breakdown voltage temperature coefficient81 mV per C
Gate threshold temperature coefficientminus 7.5 mV per C
Gate threshold at 250 microamp3.0 V minimum, 5.0 V maximum
Gate leakage at 20 V100 nA maximum
Drain leakage at 100 V, 25 C and 70 C1 and 15 microamp
On state drain current at 10 V gate40 A minimum
On resistance at 10 V gate and 10 A0.017 ohm typical
On resistance at 7.5 V gate and 10 A0.020 ohm typical
Forward transconductance at 10 A46 S typical
Input, output and reverse transfer capacitance at 50 V1470, 132 and 11.2 pF
Total gate charge at 10 V and at 7.5 V20 and 15 nC
Gate source and gate drain charge6.45 and 3.5 nC
Output charge at 50 V22 nC
Gate resistance at 1 MHz0.2, 0.76 and 1.4 ohm
Turn on delay and rise time at 10 V drive12 and 5 ns typical
Turn off delay and fall time at 10 V drive19 and 5 ns typical
Turn on delay and rise time at 7.5 V drive15 and 6 ns typical
Body diode forward drop at 5 A0.78 V typical, 1.1 V maximum
Body diode recovery time43 ns typical, 86 maximum
Body diode recovery charge72 nC typical, 144 maximum
Reverse recovery fall and rise time33 and 10 ns
Operating junction and storage rangeminus 55 to plus 150 C

Twenty five degrees per watt on a one inch board, and what that means at 10 A

The board level thermal row is the honest one. 25 C per watt maximum with a 10 s pulse allows 5.0 W for a 150 C junction in a 25 C room, and 5.0 W through 0.017 ohm is 17.1 A, which is why the package can claim a 10 A board rating with margin at room temperature. At 70 C ambient the same row allows 3.2 W, which is 13.7 A cold, and that is where the 8.5 A printed row comes from once the resistance rises.

Resistance does rise, and the sheet does not print a hot on resistance row at all. A 100 V trench die of this generation roughly doubles between 25 C and 150 C, so the working figure at 10 A is nearer 0.034 ohm and the loss is 3.4 W rather than 1.7 W. At 25 C per watt that is 85 C of rise from the board, which puts the junction near 110 C in a 25 C room and near the limit in anything warmer. We budget on the doubled figure.

The case level rows are the other extreme. 60 W at a 25 C case through 2.0 C per watt is 120 C of rise, and the 30 A rating at 0.017 ohm is 15.3 W of conduction, so the die is nowhere near its thermal ceiling when the case is held cold. This part only reaches its headline current with a copper pour and a fan, or with the drain pad soldered to a large plane on a thick board.

Three places where the sheet needs a second read

The avalanche rows agree with each other, which is worth stating because several sheets in this shipment do not. 20 mJ is printed against a 0.1 mH coil and a 20 A start, and half of 0.1 mH times 400 is 20 mJ exactly. An unclamped inductive load at 20 A therefore sits right at the rating rather than below it, and a converter that expects to survive a repeated clamp at that current needs either a higher energy part or a clamp that keeps the current lower.

The diode current rows look generous until the condition is read. The 56 A continuous diode row is a case at 25 C figure with a duty cycle that keeps the average junction cool, and the same row on a board at 25 C is 4.5 A. A synchronous converter that relies on the body diode during a long dead time will overheat it at currents the channel handles without complaint.

The leakage row is specified at 70 C rather than the usual 125 C, which is a lower temperature than the rest of the table. That makes the 15 microamp figure look tighter than a 125 C reading would, and a converter that runs its die at 110 C should expect several times that value. It matters in a battery path, where a microamp at 48 V still drains a pack over a month.

Where a 100 V, 17 milliohm part earns its place

An isolated 48 V to 12 V converter at 200 W to 400 W, a secondary side synchronous rectifier in a forward, and a hot swap switch on a 48 V backplane all fit. The gate charge of 20 nC at 10 V is small enough to switch at 200 kHz from a modest driver, and the 5 ns fall time keeps the turn off loss inside a watt at 10 A.

The part does not fit a 5 V driven rail, a stage that needs the body diode to carry current for a long interval, or a fanless board running more than 8 A continuous. In those three cases a lower threshold part, a larger body or a two device parallel arrangement is the answer, and the sheet has the rows to show it before the board is cut.

Our power management cross reference work keeps the threshold window, the board level thermal row and the diode current row per approved alternate for exactly this reason: a 100 V part at 17 milliohm with a 1.5 V threshold and a 20 C per watt board path is not the same component as this one, even though both print 100 V and 17 milliohm on a distributor page.

Questions we answer before a reel is booked

First, the drive level. If the gate is driven from 5 V, this part is not specified for it and the 7.5 V row is the lowest published point. A gate driver running from a 12 V rail with a 10 ohm resistor turns the part on in 5 ns and off in 5 ns, and the 1.4 ohm maximum internal gate resistance is small enough that the external resistor sets the edge.

Second, the board. Ten amps continuous on a one inch square of two ounce copper is a 25 C per watt path only if the drain pad is fully soldered with no voids, and a DFN with a 20 per cent void area is a different thermal part. We ask for the copper area and the void limit before we approve the position.

Third, the alternate. A 100 V part at 15 to 20 milliohm in a 5 by 6 body comes with thresholds from 1.5 V to 4 V and board thermal rows from 15 C to 40 C per watt, and the spread decides both the drive and the heatsink. We hold those three rows per approved alternate, the incoming inspection plan measures the lot against them, and the pin to pin comparison starts from the 5 by 6 land pattern, the pin 1 marker and the exposed pad size rather than from the current column.