VBPB1603
Product Specifications
VBPB1603
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBPB1603 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBPB1603: 60 V and 210 A in TO3P at 3 milliohm
The VBPB1603 is a single N channel MOSFET in the TO3P body, printed at 60 V drain to source, plus or minus 20 V on the gate, a 3 V threshold, 210 A of drain current, 3.6 milliohm at a 4.5 V gate and 3 milliohm at a 10 V gate. The vendor table gives the structure as trench. This is the highest current part in this band and the one that is bought for a low voltage bus where the current is the constraint rather than the voltage.
At 3 milliohm the die is a large area trench cell. The resistance is low enough that the package and the interconnect start to matter: a TO3P lead frame adds 0.2 to 0.5 milliohm, the source bond wires add a similar amount, and the tab resistance is in series with the drain. The 3 milliohm figure is a die number, so a board that measures the resistance at the pins will see 3.5 to 4.5 milliohm and should plan for it.
The 210 A figure needs the same reading as every current rating in a plastic body. It is a die limited number at a 25 C case with the junction held at 25 C, which no heatsink achieves. The working current is set by the loss the package can pass, and that is a very different number.
Key data for the VBPB1603
| Configuration | Single N channel |
| Package | TO3P, through hole, tab on the drain |
| VDS | 60 V |
| VGS | Plus or minus 20 V |
| Vth | 3 V typical |
| ID | 210 A at a 25 C case |
| RDS(on) at 4.5 V | 3.6 milliohm |
| RDS(on) at 10 V | 3 milliohm |
| Structure | Trench |
| Conduction at 50 A | 7.5 W |
| Conduction at 100 A | 30 W |
| Conduction at 150 A | 67.5 W |
| Conduction at 210 A | 132 W |
What a 60 V part is for
48 V is the rail this class serves. A 48 V battery pack runs from 39 V empty to 54.6 V full, and a switching stage on that rail sees the pack voltage plus the spike from the loop inductance. A 60 V part holds a margin of 1.1 against a full pack, so the clamp and the loop have to be good, but the resistance is low enough that the conduction loss at 50 to 100 A is manageable. Every 48 V telecom rectifier, e-bike controller and 48 V server power shelf uses this class.
The second use is a 24 V or 12 V system with a very high current. A 12 V, 1 kW load draws 83 A, and at 3 milliohm that is 21 W. The same load at 60 V draws 17 A and the part would be a 100 V or 150 V device with ten times the resistance, so the low voltage does buy something as long as the current is carried by copper rather than by the die.
The third is a battery protection or load switch, where the part is on continuously and the only loss that matters is the on state. Those boards run the part at 20 to 30 percent of its thermal limit and pay for the low resistance with board area.
Package limits at 100 A and above
At 100 A and 3 milliohm the die makes 30 W, and at 150 A it makes 67.5 W. A TO3P body can pass 30 W to a heatsink with a plate and a fan, and it cannot pass 67.5 W without a copper block and a forced draft. The tab area is the limit: about 1.5 square centimetres of copper, with a spreading resistance from the die to the tab that dominates at high current density.
The source bond wires are the other limit. At 150 A each wire carries 30 to 40 A, and the wires are 200 to 300 micron aluminium or copper. The fusing current of a single wire is far above that, but the resistance of the wire string is 0.2 to 0.5 milliohm, which is 5 to 11 W at 150 A in the package alone. That loss is inside the package and has to leave through the same tab.
The third limit is the pin. A TO3P pin is rated for 30 to 50 A continuously in free air, so a 100 A stage uses all three pins or a copper bus bolted to the tab. Where the current is above 150 A the right answer is two parts in parallel, not a bigger single die, because the parallel pair halves the package loss as well as the die loss.
Driving a 3 milliohm die
The gate charge of a die this large is high, in the region of 150 to 250 nC. At 100 kHz that is 15 to 25 mA of average gate current at 10 V, which a small driver can supply, but the peak current during the plateau is 3 to 6 A if the transition has to finish in 50 ns. A weak driver turns the part on slowly, and a slow turn on through 100 A into a 3 milliohm load is a 30 W transient in the die for 200 ns.
Vth at 3 V means the part is not logic level in the strict sense. A 4.5 V drive gives 3.6 milliohm, which is 20 percent above the 10 V figure, and that difference is 6 W at 100 A. If the gate driver only has 5 V, the loss calculation should use 3.6 milliohm and not 3 milliohm.
The 60 V trench die has a body diode with a forward drop of 0.7 to 0.9 V at rated current, so a freewheel interval at 100 A dissipates 70 to 90 W in the diode. In a synchronous stage that interval is short and the low side channel carries the current instead. In a stage that relies on the body diode, the diode loss sets the thermal limit, not the channel.
Where a board has a mixed set of 60 V codes from different lines, the supplier scorecard page covers how delivery and lot quality are tracked across a year, and the date code management page covers how material is aged and set aside before it is built.
The sourcing side of this part is covered on the supplier scorecard. For a 60 V part used at 100 A, that page covers how the source is scored on delivery and lot quality.
Questions we get on this code
Is 210 A usable in a TO3P? No. The body passes 30 to 40 W to a good heatsink, which is 100 A at 3 milliohm on a hot die and 60 to 70 A on a plate without a fan. The 210 A label is a die number at a 25 C case.
Do I need 10 V on the gate? It helps. The 4.5 V figure is 3.6 milliohm and the 10 V figure is 3 milliohm, so a 5 V driver costs about 20 percent more conduction loss at full current.
Can two of them be paralleled? Yes, and above 120 A it is the better route than one die. Match the gate resistors and give each part its own source return, otherwise the faster part takes the current during every transition.
What kills this part in the field? Almost always the drain spike from the loop inductance at turn off, not the current. A 60 V part on a 54 V pack has 6 V of headroom, and a 50 nH loop at 100 A and 30 ns produces 165 V of spike unless the clamp and the loop are tight.