Contact Us

VBPB15R18S

Brand: VBsemi
VBsemi VBPB15R18S is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBPB15R18S — Discrete & Power Semiconductors | Superb Automation

VBPB15R18S

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBPB15R18S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBPB15R18S: 500 V and 18 A in TO3P with 210 milliohm

The VBPB15R18S is a single N channel MOSFET in the TO3P body, printed at 500 V drain to source, plus or minus 30 V on the gate, a 3.5 V threshold, 18 A of drain current and 210 milliohm at a 10 V gate. The vendor table gives the structure as SJ_Multi-EPI, a multi epitaxial superjunction die, which is unusual in this voltage class and is what makes 210 milliohm possible at 18 A.

The 500 V class is the one that gets skipped. Most offline circuits go straight to 600 or 650 V because the parts are everywhere and the price is set by volume. A 500 V part makes sense where the bus is 200 to 300 V, which is a 110 to 230 V single phase supply with a modest surge allowance, or where the topology clamps the switch node and the steady voltage never reaches the rectified peak.

TO3P is the three pin plastic body with the same footprint family as TO247 but a smaller tab and a lower thermal path. It suits 15 to 30 W of dissipation in a converter with a plate heatsink, and it is the reason this part is priced where it is rather than at the TO247 level.

Key data for the VBPB15R18S

ConfigurationSingle N channel
PackageTO3P, through hole, tab on the drain
VDS500 V
VGSPlus or minus 30 V
Vth3.5 V typical
ID18 A at a 25 C case
RDS(on) at 10 V210 milliohm
StructureMulti epitaxial superjunction
Conduction at 5 A5.3 W
Conduction at 8 A13.4 W
Conduction at 12 A30.2 W
Conduction at 18 A68 W

The voltage margin question

A 230 V AC supply rectifies to 325 V. A flyback or a forward converter puts the switch node at the bus plus the reflected output voltage plus the leakage spike, and the reflected term is set by the turns ratio. On a 12 V output with a 5 to 1 ratio the reflected voltage is 60 V, and the leakage spike adds 100 to 150 V with a well damped clamp. The sum is 490 to 535 V, which is why 600 V is the normal pick and why 500 V only works when the clamp is tight and the ratio is low.

Where the class does work is a 110 V supply, where the rectified bus is 155 V, and a two transistor forward or a half bridge where the switch never sees more than the bus. In those topologies the reflected voltage is not across the switch, so 500 V gives a margin of 2.1 against 325 V and 3.2 against the 155 V bus. It also works on the secondary side of a high voltage converter, where the switch sits on a 300 to 400 V rail that is regulated and has no surge.

It is worth being explicit about the trade: the 500 V die is smaller than the 650 V die for the same current, so the capacitance is lower and the switching loss is lower, but the avalanche headroom is also lower. A circuit that relies on the clamp absorbing a lightning surge needs the 650 V part, and a circuit with a real clamp and a regulated rail does not.

Losses in the TO3P body

At 210 milliohm the die makes 5.3 W at 5 A, 13.4 W at 8 A, 30.2 W at 12 A and 68 W at the printed 18 A. As with every superjunction die the resistance rises with temperature, roughly doubling by 125 C, so the 8 A figure on a hot die is 27 W rather than 13.4 W.

The TO3P tab is smaller than a TO247 tab and the junction to case resistance is correspondingly higher, in the region of 0.8 to 1.4 K per watt for a die of this size. At 13 W and 1.1 K per watt the junction sits 14 K above the case, and with a mounted interface of 0.5 K per watt the heatsink at 90 C gives a junction near 120 C. That is the working point: 6 to 9 A continuous on a plate, 12 to 14 A on a fan cooled sink.

The switching side is where this part is easier than a 650 V device. The output charge of a 500 V die at this current is around half that of a 650 V die of the same resistance, so at 100 kHz and 8 A the crossover loss is 6 to 8 W rather than 12 to 15 W. A 100 kHz flyback in the 60 to 100 W range is the natural home for it.

Where it is used, and how to buy it

Auxiliary supplies in industrial equipment, LED drivers on a 230 V line with a tight clamp, small motor drives on a 200 V DC rail, and the primary side of a 48 V telecom converter are the four places this part lands. In each case the current is 5 to 12 A and the switching frequency is 60 kHz or above, which is exactly where a smaller die with lower capacitance wins.

The 500 V superjunction class is thinner than the 600 and 650 V classes. Fewer lines make the die and the second source is usually a different structure with a different capacitance, so a swap changes the EMI signature. Where a lot has to be checked before release, the supplier quality audit page covers what is inspected at the source, and the incoming inspection plan page covers what is measured on arrival so a part with the wrong marking never reaches the line.

The sourcing side of this part is covered on the supplier quality audit. For a 500 V part with a thin second source, that page covers what is checked at the source before release.

Questions we get on this code

Will it replace a 600 V part on the same board? Only after the switch node voltage is measured on the bench. A 600 V part in the same footprint usually has a higher resistance, so the swap lowers the conduction loss, and a clamp that was tuned for the slower die will ring harder on the faster one.

Is 210 milliohm a maximum or a typical figure? The vendor table prints a single value, so treat it as a nominal. A production lot can sit 10 to 20 percent above it, and a board at 200 milliohm nominal with no margin will lose 5 to 8 W more than the calculation says.

What gate drive does it need? Vth is 3.5 V, so a 10 V drive is needed for the printed resistance. A 5 V logic level drive leaves the part partly on and the resistance three to five times higher.

Is the tab isolated? No. The tab is the drain, so the heatsink has to be isolated or the sink has to float at the switch node. An insulating pad adds 0.3 to 0.8 K per watt and has to be in the thermal budget.