VBP19R47S
Product Specifications
VBP19R47S
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBP19R47S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBP19R47S: a 900 V superjunction N channel MOSFET in TO247
The VBP19R47S is a single N channel MOSFET in the TO247 body, printed at 900 V drain to source, plus or minus 30 V on the gate, a 3.5 V threshold, 47 A of drain current and 100 milliohm on resistance at a 10 V gate. The vendor table gives the structure as SJ_Multi-EPI, which is a multi epitaxial superjunction die rather than a planar or a single step trench.
Multi epitaxial means the drift region is built up in several epitaxial layers, with the charge balance columns formed between them. The result is a drift region that carries 900 V in a thickness that a planar die of the same rating could not use, which is why the on resistance lands at 100 milliohm instead of the 1.2 to 1.5 ohm a planar 900 V part of this current class would show. The trade is process complexity and a tighter tolerance on the charge balance, neither of which is visible to the buyer except in the price and in how few lines make the part.
This is the part that sits between the 650 V band and the 1200 V band. A 480 V three phase supply rectifies to 680 V DC, and a regenerative event on the line pushes the bus towards 760 to 800 V before a brake chopper takes over. A 650 V part does not survive that bus. A 1200 V part survives it with a die twice the area and twice the resistance. The 900 V class is the compromise, and 100 milliohm at 47 A is a workable compromise for a 5 to 15 kW stage.
Key data for the VBP19R47S
| Configuration | Single N channel |
| Package | TO247, through hole, tab on the drain |
| VDS | 900 V |
| VGS | Plus or minus 30 V |
| Vth | 3.5 V typical |
| ID | 47 A, a die figure at a 25 C case |
| RDS(on) at 10 V | 100 milliohm |
| Structure | Multi epitaxial superjunction |
| Conduction at 10 A | 10 W |
| Conduction at 20 A | 40 W |
| Conduction at 30 A | 90 W |
| Conduction at 47 A | 221 W |
What a 900 V rating covers on a real bus
A 400 V AC drive rectifies to 565 V DC. The usual rule for the switch is that the part should hold twice the steady bus, which puts this class at 1100 to 1200 V and explains why 1200 V IGBTs dominate that application. Where the bus is 480 V AC, the rectified figure is 680 V and a 900 V part holds a margin of 1.32 at the steady state and about 1.18 during a 10 percent line swell. That is enough when the board has a brake chopper or a clamp, and it is not enough when the line can regenerate without either.
The second place the class appears is the boost stage of a solar string inverter. A string of 16 to 20 panels at 40 V open circuit sits at 640 to 800 V, and the boost runs from that to a 800 V DC link. The switch sees the link plus the diode drop on every cycle, so 900 V is the rating that fits, and the current is 10 to 20 A for a 6 to 10 kW inverter.
A third use is the front end of a 480 V charger or a high voltage battery test supply. The switch carries the PFC inductor current at 20 to 35 A and the bus sits at 750 to 800 V. Here the on resistance matters less than the capacitance, because a 65 kHz PFC spends more time in transition than in conduction at light load.
Losses and the TO247 thermal path
At 100 milliohm the die makes 10 W at 10 A, 40 W at 20 A, 90 W at 30 A and 221 W at the printed 47 A. Those numbers are at a 25 C junction. On a superjunction die the resistance roughly doubles by 125 C, so the 20 A figure becomes 80 W on a hot die and the 10 A figure 20 W. Sizing the heatsink from the 25 C number is the most common way this part gets picked wrongly.
A TO247 tab is about 1.5 square centimetres of copper, with a junction to case resistance in the range of 0.4 to 0.8 K per watt for a die of this area, and a mounted interface that adds 0.3 to 0.8 K per watt depending on the pad and the torque. Taking 0.6 plus 0.5 as a working pair, 40 W puts the junction 44 K above the heatsink, so a heatsink at 80 C leaves a junction at 124 C and the part is inside its limit at 20 A. At 30 A the same sink leaves the junction near 160 C, which is past the 150 C ceiling. The honest continuous figure is 18 to 25 A on a fan cooled sink and 10 to 14 A on a natural convection plate.
Switching loss is the other half. A 900 V superjunction die has a small die area for its voltage, so the output charge is modest, but the drain voltage swing is 700 V and the current is tens of amps. At 65 kHz with a 40 ns crossover the loss is around 15 to 20 W at 25 A, which is comparable to the conduction loss and has to be in the thermal budget from the start.
Where this part fits, and what to check before a swap
Motor drives on a 480 V line, string inverter boost stages, high voltage battery test equipment and the PFC front end of a 480 V charger are the four applications where the 900 V, 100 milliohm combination lands. In each of them the part is chosen for the voltage, and the current is set by the die that happens to come with that voltage in the family.
Before a swap from a 1200 V part, three things have to line up. The avalanche rating has to cover the leakage spike, and a superjunction die has a smaller package for the same voltage, so the spike is higher unless the clamp is tightened. The gate charge is lower, which changes the driver, and a driver tuned for a 1200 V planar part will overshoot the gate on this die unless the resistor is raised. The body diode reverse recovery is faster, which is good for a half bridge and hard on the opposing switch if the dead time is long.
On the sourcing side, a 900 V multi epi die is made on fewer lines than the 600 and 650 V classes, and the part is bought as a single source more often than buyers assume. Where a board has to keep running through a line stop, the strategic sourcing page covers how one code is held against a build plan rather than re-bought each quarter, and the pin to pin cross reference page covers which parameters have to match before a second source is signed off.
The sourcing side of this part is covered on the strategic sourcing. For a 900 V code that sits on one line, that page covers how the supply is held against a build plan.
Questions we get on this code
Is 100 milliohm the hot figure? No. The table gives the 10 V gate value at room temperature. At 125 C the same die is close to 200 milliohm, and a calculation that sizes the sink from 100 milliohm will run 20 to 25 K hotter than expected.
Can it replace a 1200 V IGBT directly? Electrically the voltage class is lower, so the bus has to be checked first. Once it is, the drive changes: this part wants 10 V on and 0 V off, where the IGBT wanted 15 V on and a negative off bias.
What is the current at 100 kHz? The die can switch there, but the loss at 25 A and 700 V is around 25 W of crossover alone, so the practical ceiling is 40 to 50 kHz at full current and 100 kHz only at 10 A or below.
How is the date code read? The marking on the tab is the only place the lot and the date live. A reel or a tube without a readable marking is material to hold at goods inwards rather than to release to the line.