Contact Us

VBP19R15S

Brand: VBsemi
VBsemi VBP19R15S is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBP19R15S — Discrete & Power Semiconductors | Superb Automation

VBP19R15S

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBP19R15S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBP19R15S: 900 V and 15 A in a TO247 with 370 milliohm

The VBP19R15S is a single N channel MOSFET in a TO247 body, rated at 900 V drain to source, plus or minus 30 V on the gate, a 3.5 V threshold, 15 A of drain current and 370 milliohm at a 10 V gate. The vendor table lists a superjunction multiple epitaxy die.

Nine hundred volts is the class for a 480 V three phase line with a braking load, and for a 690 V line at reduced margin. On a 480 V line the bus is 680 V and the margin is 220 V, which covers a regeneration to 750 V and a clamped surge at 850 V. That margin is why drives with cranes, presses and hoists use this class rather than 800 V.

Three hundred and seventy milliohm at 15 A is a modest die. At 15 A it makes 83 W, at 11 A 45 W, at 8 A 24 W and at 4 A 6 W. On a plate heatsink the working current is 4 to 6 A, and on a fan cooled heatsink 7 to 9 A. This is an auxiliary switch or a small drive stage rather than a main switch at full load.

Key data for the VBP19R15S

ConfigurationSingle N channel
PackageTO247, through hole, tab on the drain
VDS900 V
VGSPlus or minus 30 V
Vth3.5 V typical
ID15 A
RDS(on) at 10 V370 milliohm
StructureSuperjunction, multiple epitaxy
Loss at 4 A5.9 W
Loss at 8 A23.7 W
Loss at 11 A44.8 W
Loss at 15 A83.2 W

What 900 V covers that 800 V does not

On a 480 V line a braking motor takes the bus from 680 V to 750 V, and a fast stop can push it to 800 V before the brake chopper catches it. An 800 V part is at its rating at that moment, and a 900 V part has 100 V of margin.

A surge on the line, clamped at 850 V by a varistor, is the second case. An 800 V part is over its rating and a 900 V part is inside it. The two cases together are why the 900 V class exists on 480 V lines with mechanical loads.

On a 690 V line the rectified bus is 975 V and neither class works. That line needs 1200 V, and the 900 V class is not a compromise there, it is simply wrong.

Loss at the working point

At 6 A and 370 milliohm the loss is 13 W cold and 24 W hot. A TO247 on a 1.5 K per watt plate heatsink at 40 C ambient sits at 93 C junction, which is comfortable. At 9 A the hot loss is 54 W and the junction is at 166 C, which is outside.

That narrow window is the story of a high voltage part at moderate current. The resistance is six times the 600 V part at the same current label, so the working current is a third of it. The label of 15 A is a die rating, not a working point.

Switching at 680 V and 6 A with a 40 ns crossover is 4 W peak, and averaged at 8 kHz it is under 1 W. In a drive at 8 kHz the conduction term dominates and the resistance is the whole budget.

Where this part fits

480 V drives with braking loads at 0.75 to 1.5 kW, auxiliary and bias supplies on a 680 V bus, active clamps in flyback stages at 600 V, and startup paths in high voltage supplies. It also appears in the discharge circuit of a high voltage capacitor bank, where the switch is in series with a resistor and the current is small.

In a small drive the part runs at 4 to 8 kHz in a half bridge and the body diode carries the motor current during the dead time. At 6 A the diode drop of 1.3 V is 8 W during the dead time, which is a small share of the cycle.

For a 690 V line this class is not usable. Where a product family has both 480 V and 690 V variants, the 1200 V class covers both and the 900 V class only one. The last time buy and LTB planning page covers how a thin voltage class is held when its line narrows.

At 370 milliohm the die is small enough that a short circuit is a real risk. During a fault the current rises until the controller reacts, and the die absorbs the energy of the bus voltage times the current for that interval. A controller with a 5 microsecond limit keeps the die inside its thermal transient capability. A controller that takes 50 microseconds to react puts the die outside it, and the failure appears as a shorted gate rather than as a burnt die, because the gate oxide fails first under the heat.

The sourcing side of this part is covered on the component obsolescence management. For a thin 900 V class, that page covers how the supply is watched before the family narrows.

Questions we get on this code

Is 900 V a thin class? Yes. Fewer lines make 900 V than 800 V or 1200 V, so the second source question arrives earlier. Plan it before the first build.

Can a 1200 V part be used instead? Electrically yes, with more margin and about twice the resistance for the same die area. On a 480 V line with a 6 A load that is usually acceptable and removes the thin class risk.

What is the hot resistance? About 1.8 times the printed value, so 670 milliohm at 125 C. At 6 A that is 24 W rather than 13 W.

Is the body diode fast? The table does not print an FD grade for this code. In a bridge at 8 kHz the recovery is small, and above 20 kHz it should be measured.