Contact Us

VBP16R67S

Brand: VBsemi
VBsemi VBP16R67S is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBP16R67S — Discrete & Power Semiconductors | Superb Automation

VBP16R67S

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBP16R67S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBP16R67S: 600 V and 67 A in a TO247 with 34 milliohm

The VBP16R67S is a single N channel MOSFET in a TO247 body, rated at 600 V drain to source, plus or minus 30 V on the gate, a 3.5 V threshold, 67 A of drain current and 34 milliohm at a 10 V gate. The vendor table lists a superjunction multiple epitaxy die. It is the second largest member of the 600 V family and the one used for the main switch of a 2 to 3 kW stage.

Thirty four milliohm at 600 V is a die close to the full area of a TO247 cavity. At 67 A the die makes 153 W, at 50 A 85 W, at 34 A 39 W and at 17 A 10 W. On a fan cooled heatsink with forced air the working current is 25 to 32 A, and on a plate heatsink 12 to 15 A.

The part exists because a 3 kW stage at 400 V wants one switch rather than two, and one TO247 at 34 milliohm is the largest single die that fits. Above 3 kW the answer is two parts in parallel, not a bigger body.

Key data for the VBP16R67S

ConfigurationSingle N channel
PackageTO247, through hole, tab on the drain
VDS600 V
VGSPlus or minus 30 V
Vth3.5 V typical
ID67 A
RDS(on) at 10 V34 milliohm
StructureSuperjunction, multiple epitaxy
Loss at 17 A9.8 W
Loss at 34 A39.3 W
Loss at 50 A85.0 W
Loss at 67 A152.6 W

Thermal limit before the die limit

At 30 A continuous and 34 milliohm the loss is 31 W cold and 55 W hot. A TO247 junction to case at 0.4 K per watt and a pad at 0.4 K per watt puts the case 44 C below the junction at 55 W, so with a 0.6 K per watt heatsink at 45 C ambient the junction is at 144 C. That is at the limit and not inside it.

A fan cooled heatsink at 0.3 K per watt brings the junction to 111 C at 30 A, which is a working condition. At 25 A the hot loss is 38 W and the junction is at 95 C, which is comfortable.

The lesson is that a 67 A label does not mean 67 A in a sealed box. The working figure is 25 A with forced air and 12 A without, and the ratio between the two is the ratio of the heatsink resistances rather than anything to do with the die.

Two of these against one larger die

At 4 kW from a 400 V bus the input current is 10 A average and 27 A peak. One part at 34 milliohm carries 25 W of conduction loss hot and 5 W of switching, so 30 W in one TO247. Two parts in parallel share 15 W each and run 30 C cooler, which is usually the difference between a life of 100,000 hours and 30,000 hours at the electrolytic capacitors around them.

Paralleling costs a second part, a second gate resistor and a symmetric source bus. At 4 kW that is cheaper than a larger heatsink and a fan, and it also halves the thermal cycling on each die.

The gate drive has to be split per part rather than shared through one resistor, because a shared resistor lets the faster die take the switching loss. Two 4.7 ohm resistors fed from one driver keep the two transitions within a few nanoseconds.

Where this part fits

Power factor stages from 2 to 3 kW, server power supplies at 2 kW with a 400 V bus, EV onboard chargers at 3.3 kW, and solar microinverters at 500 W per channel. In a server supply the part runs in a bridgeless power factor stage at 65 to 100 kHz, and the switching loss is a third of the total.

In a charger the part runs in a boost stage at 100 kHz and the gate charge sets the driver loss. At 60 to 80 nC per cycle and 100 kHz the driver delivers 7 mA average, which any 1 A driver handles.

For a 480 V three phase line this class is not usable, because the rectified bus is 680 V. The incoming inspection plan page covers what is measured on each lot of a high current part before it reaches the line, since a mixed lot of two grades is the usual failure.

At 34 milliohm the wire bonds inside the package are part of the resistance. A TO247 of this class carries the source with four to six aluminium bonds in parallel, and the bond contribution is 3 to 5 milliohm of the printed figure. That is why the resistance rises with temperature faster than the silicon alone would suggest, and why a four lead body with a separate source return measures lower in circuit. The vendor table gives the die plus bonds as one number, and the board sees that whole number.

The sourcing side of this part is covered on the date code management. For a high current part held between builds, that page covers how the age is tracked and when material is set aside.

Questions we get on this code

Can it run at 67 A with a fan? At 67 A the hot loss is 270 W and the junction is far above its limit even with forced air. The die rating is not a working current.

Does it have a fast recovery body diode? The table does not list an FD grade for this code. In a hard switched bridge, check the recovery before release, because a standard superjunction diode at 25 A is significant.

What is the avalanche rating? Not published. A boost stage needs the leakage of the boost inductor handled by the diode and the output capacitor, not by the switch, so the clamp is part of the circuit.

Is it available in a TO247 four lead body? Not as this code. The four lead body is a separate part, and the extra source pin reduces the source inductance rather than changing the die.