Contact Us

VBP16R20SFD

Brand: VBsemi
VBsemi VBP16R20SFD is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBP16R20SFD — Discrete & Power Semiconductors | Superb Automation

VBP16R20SFD

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBP16R20SFD from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBP16R20SFD: 600 V at 0.175 ohm and 20 A, the small end of the fast diode family

The VBP16R20SFD is a 600 V N channel super junction MOSFET with a fast body diode, in the TO-247 body, rated 20 A at a 25 C case and 0.175 ohm at a 10 V gate measured at 6.5 A. It is the smallest member of the family that the 41 A, 42 A and 64 A parts belong to, and it shares their thermal table, their diode test condition and their page structure.

At 600 V and 0.175 ohm the part covers the 100 W to 400 W end of the off line market: an auxiliary supply inside a motor drive, a 150 W adapter, a small continuous conduction power factor stage, an LED driver of 60 W to 150 W, and the HID ballast that the applications list names. In all of those the current is 2 A to 6 A and the conduction loss is 0.7 W to 6.3 W, which a TO-247 removes without a fan.

The interesting feature of this sheet is not the headline but the honesty of the dissipation row. 150 W at a 25 C case is below what the 0.57 C per watt junction to case path would carry, so the printed figure is conservative rather than optimistic, and that is unusual in this shipment where four sheets print dissipation rows above their own thermal path.

The parameter table in full

Drain source voltage at maximum junction temperature600 V
Gate source voltageplus or minus 30 V
On resistance at 10 V gate and 6.5 A0.175 ohm typical
Gate threshold at 250 microamp2.5 V minimum, 4.5 V maximum
Gate source leakage at 20 V and at 30 Vplus or minus 100 nA and plus or minus 1 microamp
Drain leakage at 600 V, 25 C and 125 C1 microamp and 100 microamp
Forward transconductance at 6.5 A5.6 S typical
Input, output and reverse transfer capacitance2300, 80 and 4 pF
Effective output capacitance, energy and time related63 and 213 pF
Total gate charge at 10 V, 520 V and 8 A53 nC typical
Gate source and gate drain charge15 and 19 nC
Turn on delay and rise time at 520 V and 8 A18 and 24 ns typical, 25 and 55 maximum
Turn off delay and fall time, same conditions80 and 12 ns typical
Internal gate resistance at 1 MHz0.8 ohm
Continuous source drain diode current20 A
Pulsed diode forward current60 A
Diode forward voltage at 8 A1.5 V maximum
Reverse recovery time at 8 A and 400 V80 ns typical
Reverse recovery charge and peak current5.8 microcoulomb and 30 A
Single pulse avalanche energy, 28.2 mH and 7.5 A950 mJ
Maximum power dissipation, case at 25 C150 W
Junction to case and junction to ambient0.57 and 62 C per watt
Continuous drain current at 25 C and 100 C case20 A and 12 A
Pulsed drain current60 A
Drain source and diode voltage slope50 and 15 V per ns
Operating junction and storage rangeminus 55 to plus 150 C

What 0.175 ohm costs at the currents this part actually sees

At 5 A the channel sheds 4.4 W, at 10 A it sheds 17.5 W, and at the 20 A continuous row it sheds 70 W. The 150 W dissipation row is reached at 29 A, which the part cannot carry through the package, so the current rows bind before the dissipation row does and the 20 A figure is a packaging and bonding limit rather than a thermal one.

In still air 62 C per watt allows 2.02 W for a 125 C rise, which is 3.4 A at 25 C and 2.86 A at 50 C. So a 5 A load needs a heatsink, and the whole 20 A row needs a bolted one. This is the same arithmetic as the larger members of the family, and it is the reason a 150 W adapter with this part has a metal tab in it.

The 12 A row at a 100 C case is the realistic continuous figure inside a supply that has a fan, since 12 A through 0.175 ohm is 25.2 W and 0.57 C per watt takes the junction 14.4 C above the case, leaving 25 C of margin at a 160 C case. That margin is what carries a lightning surge or a short circuit hold up test.

The diode and the gate charge at the small end

Recovery is 80 ns with 5.8 microcoulomb and 30 A of peak reverse current at 8 A and 400 V. On a 20 A part, 30 A of peak reverse current is 150 per cent of the forward rating, which tells the reader that the diode is a fast one and not a soft one. In a 150 W continuous conduction PFC at 65 kHz the recovery loss is tolerable; in a bridge it is the largest single loss at light load.

Gate charge is 53 nC at 10 V, 520 V and 8 A, with 15 nC of gate source and 19 nC of gate drain. At 100 kHz the drive power is 0.053 W, so the driver is not a constraint and the 24 ns rise time is set by the gate resistor. The 0.8 ohm internal gate resistance is the same figure as the larger members of the family, which is what makes the switching waveform comparable across the range.

One caution applies to the capacitance rows. The output capacitance of 80 pF and the effective values of 63 pF and 213 pF are printed identically on the 20 A, 41 A, 42 A and 64 A sheets, which cannot be right for four dies of very different area. The input capacitance does scale, 2300 pF here against 6900 pF on the 64 A part, so we read the output capacitance rows from a measurement rather than from the table when the switching loss matters.

Where 0.175 ohm at 600 V is the right engineering choice

An auxiliary supply of 20 W inside a motor drive, a 150 W adapter, a 100 W LED driver, and a 60 W HID ballast all sit inside the envelope with a small heatsink, and all of them gain from the 650 V class rather than the 600 V one when the mains is 277 V. In a 277 V application the rectified rail is 390 V and a 600 V part leaves 210 V of margin before any surge, which is thin.

Above 400 W this part stops being the right choice because the conduction loss at 10 A is already 17.5 W, and a 400 W supply at 90 per cent efficiency only has 44 W of total loss to spend. A 0.06 ohm part of the same family halves that loss for a small price difference, and the choice is arithmetic rather than preference.

Our power management cross reference work keeps the recovery charge and the output capacitance per approved alternate, because at this current level the switching loss and the conduction loss are the same size and a cross reference that checks only the on resistance will move the efficiency by a point.

Questions we answer before a reel is booked

First, the avalanche row does not close. 950 mJ against a stated 28.2 mH and 7.5 A start is 793 mJ of stored energy, so the row is 20 per cent above its own test. The direction of the error is the same as on the larger 600 V and 650 V sheets in the family, which is why we ask for the unclamped inductive switching report before quoting avalanche capability at all.

Second, the voltage margin. The rating is 600 V at maximum junction temperature, which means the cold breakdown is higher but the hot breakdown is exactly 600 V. A 277 V mains rail at 390 V plus a 100 V surge leaves 110 V of margin, and a 650 V member of the family costs the same. For 277 V applications we quote the 650 V part unless the customer insists.

Third, the alternate. A 600 V super junction part at 0.175 ohm is available from several suppliers with 5.8 to 28 microcoulomb of recovery charge, and on a 20 A part the difference is a 3 W swing at 65 kHz. We hold the charge per approved alternate, the incoming inspection plan checks the lot against it, and the pin to pin comparison starts from the tab and the creepage rather than from the outline drawing.