Contact Us

VBP16R20SE

Brand: VBsemi
VBsemi VBP16R20SE is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBP16R20SE — Discrete & Power Semiconductors | Superb Automation

VBP16R20SE

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBP16R20SE from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBP16R20SE: 600 V and 20 A in a TO247 with 150 milliohm

The VBP16R20SE is a single N channel MOSFET in a TO247 body, rated at 600 V drain to source, plus or minus 30 V on the gate, a 3.5 V threshold, 20 A of drain current and 150 milliohm at a 10 V gate. The vendor table lists a superjunction deep trench die. It is the entry member of the 600 V family, one step below the more common 650 V class.

Six hundred volts is a class that exists for two reasons. Some lines are qualified at 600 V for legacy reasons and a 650 V part is not on the approved list. And a 600 V part is slightly cheaper than a 650 V part at the same resistance, because the drift region is shorter. The 50 V difference is enough to matter on a 50,000 piece build and not enough to matter on a 500 piece build.

At 150 milliohm and 20 A the die makes 60 W, at 15 A 34 W, at 10 A 15 W and at 5 A 3.8 W. On a plate heatsink the working current is 6 to 9 A, and on a fan cooled heatsink 10 to 13 A.

Key data for the VBP16R20SE

ConfigurationSingle N channel
PackageTO247, through hole, tab on the drain
VDS600 V
VGSPlus or minus 30 V
Vth3.5 V typical
ID20 A
RDS(on) at 10 V150 milliohm
StructureSuperjunction, deep trench
Loss at 5 A3.8 W
Loss at 10 A15.0 W
Loss at 15 A33.8 W
Loss at 20 A60.0 W

600 V against 650 V on the same board

A 230 V single phase line gives a 325 V bus and a 400 V boost stage, so both classes have margin. The difference shows on a surge: a 2 kV test clamped at 550 V is inside 600 V by 50 V and inside 650 V by 100 V. That 50 V is the whole argument, and it is thin enough that a poor clamp or a long trace can eat it.

Where the clamp is a metal oxide varistor with a 10 percent tolerance and a 20 percent rise at rated current, a 550 V nominal clamp reaches 660 V at the surge peak. That is above 600 V and below 650 V, which is why the 650 V class became the default in offline power and the 600 V class stayed in legacy equipment and in 380 V DC telecom systems.

A 380 V DC telecom bus has 20 percent of headroom to 456 V, and a 600 V part at that bus has 144 V of margin, which is comfortable. The class fits there without argument, and telecom rectifiers are where most 600 V parts still ship.

The 20 A label and the thermal chain

At 20 A the die makes 60 W cold and about 110 W hot, since a superjunction die at this voltage roughly doubles its resistance from 25 C to 125 C. A TO247 junction to case resistance of 0.6 K per watt puts the junction 66 C above the case at 110 W, so the case has to be at 60 C to keep the junction at 126 C.

A plate heatsink in still air at 45 C ambient has a case temperature of 75 to 85 C at 20 W, which corresponds to a working current of 11 to 12 A. That is the honest continuous figure for this body without a fan.

The switching term is small at 20 A and 400 V. A 30 ns crossover gives 8 W peak and 1.6 W at 60 kHz with a 0.2 duty, so the conduction term is 90 percent of the budget and the resistance is the only parameter that matters.

Where this part fits

Telecom rectifiers on a 380 V DC bus, auxiliary supplies on legacy 600 V qualified platforms, power factor stages at 300 to 600 W, and the high side of a low current half bridge. It also appears as a series pass element in a high voltage pre-regulator, where the dissipation is set by the drop across the part.

On a new offline product at 230 V input the 650 V class is the safer purchase, because the surge margin is wider and the price difference is a few percent. On a build that is already qualified at 600 V, changing the class means a requalification of the surge test, which costs more than the part.

Where a board mixes both classes because one sub-assembly is older, the two are not interchangeable on a purchase order even at the same footprint. The vendor consolidation page covers how a mixed class list is merged without losing the qualification on either side.

The sourcing side of this part is covered on the BOM consolidation. For a 600 V code that sits on a legacy platform, that page covers how the class is merged without losing the qualification.

Questions we get on this code

Is 600 V enough for a 230 V line? In steady state yes, with 250 V of margin at a 400 V bus. On a 2 kV surge with a clamp that rises under current, the margin can fall to zero, so the clamp has to be checked as part of the qualification.

Can it replace a 650 V part in the same footprint? Physically yes. Electrically the surge margin falls by 50 V, which is a requalification item rather than a drop in change.

Why does the table have no 4.5 V column? The vendor prints the 10 V resistance only for this die. A 5 V gate drive is outside the printed condition and the resistance at 5 V should be measured rather than assumed.

How much does the resistance rise when hot? Roughly double from 25 C to 125 C for a superjunction die at this voltage. Size the heatsink on the hot figure, not the printed one.