Contact Us

VBP165R22

Brand: VBsemi
VBsemi VBP165R22 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBP165R22 — Discrete & Power Semiconductors | Superb Automation

VBP165R22

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBP165R22 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBP165R22: 650 V and 22 A in a TO247 with 280 milliohm

The VBP165R22 is a single N channel MOSFET in a TO247 body, rated at 650 V drain to source, plus or minus 30 V on the gate, a 3.5 V threshold, 22 A of drain current and 280 milliohm at a 10 V gate. The vendor table lists a planar die. It sits between the 12 A part that is used for auxiliaries and the 36 A superjunction part that is used for the main switch of a power factor stage.

Two hundred and eighty milliohm at 650 V is what a planar die of moderate area gives. The value is high enough that the part is a 6 to 11 A continuous device on a real heatsink, and low enough that it can carry a 150 to 300 W flyback primary at 60 to 100 kHz without a parallel device. That window, 100 to 300 W at 400 V bus, is where most of these parts are bought.

The 22 A label is a die rating at a 25 C case. At 22 A the die makes 135 W, at 16 A 72 W, at 11 A 34 W, at 6 A 10 W. A TO247 on a plate heatsink removes 20 to 30 W comfortably, so the working current is around 9 to 12 A, and at 6 A the part is cool.

Key data for the VBP165R22

ConfigurationSingle N channel
PackageTO247, through hole, tab on the drain
VDS650 V
VGSPlus or minus 30 V
Vth3.5 V typical
ID22 A, a die figure at a 25 C case
RDS(on) at 10 V280 milliohm
StructurePlanar
Loss at 6 A10.1 W
Loss at 11 A33.9 W
Loss at 16 A71.7 W
Loss at 22 A135.5 W

What the 650 V class covers and where it stops

A single phase 230 V input rectifies to 325 V, and a power factor stage holds the switch node at 400 V. A 650 V part therefore runs at 0.62 of its rating in steady state, which leaves room for a 2 kV surge clamped at 500 to 550 V. That margin ratio is the reason the class is used instead of 500 V, which would sit at 0.8 of rating and clamp above it on a bad line.

Three phase 400 V input is a different problem. The rectified bus is 565 V, and a motor load that regenerates adds 10 to 15 percent. A 650 V part at 640 V is at its limit, so the class for a 400 V three phase drive is 900 V or 1200 V. The 650 V part belongs on single phase input, on a 48 V or 110 V DC input through a boost stage, and on the primary of a converter fed from a battery at 300 to 400 V.

At 300 W output with 90 percent efficiency the input is 333 W, and at 400 V that is 0.83 A average with a peak near 2.5 A in continuous conduction. The 280 milliohm part dissipates 1.8 W on that average, and 22 W at the peak if the peak lasted. Duty is what saves it, and the conduction loss has to be integrated over the cycle rather than taken at the peak.

Losses in a flyback and in a power factor stage

In a discontinuous flyback at 65 kHz the primary current ramps from zero to 3 A and back, so the root mean square current is about 1.2 A and the conduction loss is 0.4 W. Switching loss dominates at that point: 400 V, 3 A and a 40 ns crossover is 4.8 W per transition, and two transitions per cycle at 65 kHz is 0.6 W. The part is cool, and the transformer sets the temperature.

In a continuous conduction power factor stage the current is 2 A average and 5.6 A peak at 300 W, and the switch carries the full inductor current during the on time. Root mean square current is around 2.6 A and the conduction loss is 1.9 W. Switching loss at 400 V and 5.6 A with a 30 ns crossover is 3.4 W peak, and averaged over the line cycle it is 1.5 W. Total 3.4 W, which a TO247 on a small heatsink handles at 100 C junction.

At 600 W the same part is at 5 A average, 14 A peak, and the peak conduction loss is 55 W with a root mean square of 6.5 A giving 12 W. That is the point where a superjunction part at 75 milliohm takes over, and the 36 A parts in this band exist for exactly that.

Where a board is re-sourced between the two, the safety stock planning page covers how much of each voltage class is held when the build plan moves between power levels.

Where this part fits

Flyback and forward converters at 100 to 300 W from a 400 V bus, auxiliary supplies in motor drives, power factor stages at 150 to 300 W, and electronic ballasts. It is also used in the primary clamp of a two switch forward, where the clamp diodes carry the leakage energy and the MOSFET carries the magnetising current.

It is not the part for a 1 kW power factor stage, for a 400 V three phase inverter, or for a half bridge where the other switch is a fast superjunction die and the two have to share a dead time. The 3.5 V threshold helps in a bridge, but the planar capacitance does not match a superjunction partner.

At 100 kHz and above, the gate charge of this die is the limit. The driver has to supply 20 to 30 nC per cycle, and a 10 ohm gate resistor with 10 V drive gives a 300 ns transition, which is a third of the on time at 100 kHz and no longer acceptable.

The sourcing side of this part is covered on the supplier quality audit. For a 650 V line bought from a new source, that page covers what is checked before the first lot is released.

Questions we get on this code

Is there a 4.5 V resistance figure? The vendor table publishes the 10 V column only. A 5 V gate drive on this die is not a specified condition, so the resistance at 5 V should be measured on a sample rather than assumed from the 10 V number.

What is the avalanche rating? The vendor page does not print one. A flyback with a leakage spike above 650 V needs an external clamp or a part with a published avalanche energy, so the clamp is part of the circuit rather than an option.

Can two of these run in parallel? At 280 milliohm the positive temperature coefficient is weak at low current, so direct paralleling needs matched lots and a shared source connection. Below 300 W, one part is cheaper than two matched ones.

What marks the date on the body? The laser marking carries the date code and the lot, and the marking is the only traceable field. A lot with an unreadable marking is a lot to hold at incoming inspection.