Contact Us

VBP165C40-4L

Brand: VBsemi
VBsemi VBP165C40-4L is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBP165C40-4L — Discrete & Power Semiconductors | Superb Automation

VBP165C40-4L

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBP165C40-4L from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBP165C40-4L: 650 V silicon carbide in a four lead TO247

The VBP165C40-4L is a single N channel silicon carbide MOSFET in a TO247 four lead body. Drain to source is 650 V, the gate window is minus 10 V to plus 20 V, the threshold is 2 to 5 V and the on resistance is 50 milliohm at an 18 V gate. The structure is listed as silicon carbide.

The page has the same inconsistency as its sibling: the table prints 40 A in the current column and the text prints a maximum drain current of 50 A. The 40 A figure is the one that matches the table and the thermal arithmetic, and at 40 A and 50 milliohm the die makes 80 W, which is already at the top of what a TO247 removes.

The fourth lead is the reason to choose this part over the three lead version. The source return for the gate loop is separated from the power path, so the common source inductance drops, the turn on and turn off become faster and the gate no longer sees the inductive drop of the power current. At 650 V and 100 to 200 kHz that is the difference between a clean edge and a ringing one.

Key data for the VBP165C40-4L

ConfigurationSingle N channel
PackageTO247-4L, four leads with a separate source return
VDS650 V
VGEMinus 10 V to plus 20 V
Vth2 to 5 V
ID40 A in the table, 50 A in the page text, to be confirmed on the data sheet
RDS(on) at 18 V50 milliohm
TechnologySilicon carbide
Loss at 5 A1.3 W
Loss at 10 A5 W
Loss at 20 A20 W
Loss at 40 A80 W

Where the four lead body pays for itself

At 650 V the drain edge is slower than at 1200 V but the current is higher, so the product of voltage and current at the transition is similar. In a three lead body the common source inductance of 5 to 10 nanohenries turns a 20 A edge into a gate voltage of a few volts, which either slows the edge or pushes the gate toward the threshold at turn off of the opposite device.

In a four lead body that path is broken. The gate return goes to the driver ground rather than to the power source, the gate waveform stays clean, and the switching loss falls because the crossover is shorter. In a converter at 200 kHz the saving is often 2 to 4 W per device, which pays for the extra pad on the board within one thermal cycle.

The cost is routing discipline. The fourth lead has to return to the driver, not to the nearest power ground, and the return trace must not share a via with the power current. A four lead part placed with the return tied to the power ground at the device is no better than a three lead part and it costs one more pad.

Thermal and the hot resistance

Fifty milliohm is a 25 C figure at 18 V. At 125 C the die is 80 to 100 milliohm, so 20 A becomes 32 to 40 W and 30 A becomes 72 to 90 W. A TO247 on a 0.6 C per watt path holds 40 to 50 W at a case near 85 C, which puts the working current at 20 to 25 A rather than the 40 A in the table.

The switching term at 650 V in a hard switched converter is smaller than at 1200 V but not negligible. The energy in the output capacitance at 400 V and 200 kHz adds 1 to 3 W at 20 A, and a resonant topology removes most of it. Because the four lead part is chosen for fast edges, it usually appears in a converter that runs above 100 kHz, where the switching term and the thermal term have to be calculated together.

Gate drive is 18 V on with a negative bias of 3 to 5 V. The threshold spread of 2 to 5 V between parts matters at turn off, because a part with a 2 V threshold is easier to turn back on with a Miller pulse than one at 5 V. A negative bias removes the question, and the window allows down to minus 10 V.

Where the part fits and where it does not

It fits a 400 V bus inverter at 15 to 25 A, a server supply front end at 200 kHz, an on board charger, a compact motor drive, a power factor stage at high frequency and a phase shifted bridge. It does not fit a 690 V line, a 40 A continuous load without a large sink, or a board that ties the fourth lead to the power ground.

Where a four lead part is introduced into an existing board, the gate loop and the driver return are a change and not a substitution, and the first article has to be checked for ringing and for gate voltage at both turn on and turn off. Our NPI production launch checklist page covers the checks that belong in that first build.

The sourcing side of this part is covered on the supplier quality audit. For a four lead part entering a first build, that page covers what is verified at the source before release.

Questions we get on this code

Is the current 40 A or 50 A? The table prints 40 A and the text prints 50 A. We quote the table and record the discrepancy until the data sheet settles it.

Does the fourth lead fit an existing footprint? No. It needs one more pad and a return trace to the driver.

What frequency does this part suit? Above 100 kHz, where the clean edge pays for the extra pad. Below that a three lead part is simpler.

What does the order carry? Part number with the 4L suffix, TO247-4L, and tube packing. We confirm the packing and the date code on the offer.