Contact Us

VBP1601

Brand: VBsemi
VBsemi VBP1601 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBP1601 — Discrete & Power Semiconductors | Superb Automation

VBP1601

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBP1601 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBP1601: 60 V, 1.45 milliohm, and a 150 A rating the package sets rather than the die

The VBP1601 is a 60 V N channel trench MOSFET in the TO-247AC body. The summary gives 60 V, 0.00145 ohm at a 10 V gate with 30 A of test current, 0.00183 ohm at a 7.5 V gate with 20 A, 141 nC of typical gate charge and a 150 A current rating that carries a note saying the package, not the silicon, is the limit.

That note is the most useful line on page one. The drain current is printed as 150 A with the case at 25 C and still 150 A with the case at 70 C, which cannot come from a die whose on resistance rises with temperature, and it does not: it comes from the lead frame and the bond wires. A buyer who reads the flat 150 A row as thermal headroom will plan a 150 A continuous load and discover that the die is already at 32 W of conduction loss before the case is considered.

The class is the 12 V, 24 V and 48 V one. Secondary synchronous rectification in a 12 V output, OR-ing diodes in a redundant supply, a battery disconnect in a 48 V pack, a power tool trigger stage and an electronic fuse all sit inside the envelope. At 1.45 milliohm, 50 A sheds 3.6 W, which is why this part is usually found in pairs or triples on one heatsink rather than alone.

The parameter table in full

Drain source voltage60 V
Gate source voltageplus or minus 20 V
On resistance at 10 V gate and 30 A1.45 milliohm typical
On resistance at 7.5 V gate and 20 A1.83 milliohm typical
Gate threshold at 250 microamp2 V minimum, 4 V maximum
Gate body leakage at 20 Vplus or minus 250 nA
Drain leakage at 60 V, 25 C, 125 C and 175 C1 microamp, 150 microamp and 5 mA
On state drain current at 10 V gate120 A minimum
Forward transconductance at 30 A120 S typical
Input, output and reverse transfer capacitance10895, 2420 and 85 pF
Total gate charge at 10 V, 30 V and 20 A141 nC typical, 212 maximum
Gate source and gate drain charge43.6 and 19.1 nC
Output charge at 50 V143 nC typical, 215 maximum
Gate resistance at 1 MHz0.24 ohm minimum, 1.2 typical, 2.4 maximum
Turn on delay and rise time at 30 V and 10 A28 and 12 ns typical
Turn off delay and fall time, same conditions50 and 13 ns typical
Pulsed diode forward current250 A
Body diode forward drop at 10 A0.8 V typical, 1.5 maximum
Body diode recovery time at 34 A75 ns typical, 150 maximum
Peak reverse recovery current2.8 A typical, 5.6 maximum
Reverse recovery charge0.12 microcoulomb typical, 0.24 maximum
Recovery fall and rise time38 and 37 ns
Pulsed drain current for 100 microsecond500 A
Single pulse avalanche energy, 0.1 mH and 60 A180 mJ
Maximum power dissipation, case at 25 C and 125 C375 W and 125 W
Junction to case and junction to ambient on board0.4 and 40 C per watt
Operating junction and storage rangeminus 55 to plus 175 C

What the dissipation rows allow, and where the package stops you first

The 375 W row at a 25 C case through 0.4 C per watt is 150 C of rise, which is the 175 C junction from 25 C, and the 125 W row at a 125 C case is 50 C of rise to the same point. Both close, so the thermal table is internally consistent and the only unusual figure is the flat current row.

On a board the ambient path is 40 C per watt, which allows 3.75 W for a 150 C rise from a 25 C room, and that is 50.9 A through the 25 C on resistance. The sheet prints no hot on resistance row, only the normalized curve, and that curve roughly doubles the figure by 125 C, so a realistic budget is 2.75 milliohm and about 37 A in still air. Everything above that needs a heatsink, and the 150 A row needs one that holds the case near 60 C.

The parallel case is worth stating because it is where these parts are actually used. Two of them at 1.45 milliohm share 100 A into 3.6 W each if they share exactly, but the gate resistance spread of 0.24 ohm to 2.4 ohm means they do not switch at the same instant unless the external resistor dominates, and the slower device takes the current for the whole overlap. Paralleling without a common gate resistor per device is how a pair becomes one hot part and one cold part.

The dynamic rows that decide a synchronous rectifier

Output charge is 143 nC typical and 215 nC maximum at 50 V. In a 12 V output rectifier at 200 kHz the charge that has to be recovered at every cycle costs 0.34 W per device, and in a 48 V rail it costs 1.37 W, which is larger than the conduction loss at 20 A. That is the reason a 60 V part with 1.45 milliohm is chosen for the low voltage rails and a different body for the 48 V ones.

Gate drain charge of 19.1 nC against 43.6 nC of gate source charge is a fast, well behaved split, and the 28 ns turn on delay with a 12 ns rise time describes a die that switches before the driver has finished its own rise. The diode is the other half: 75 ns of recovery at 34 A with 0.12 microcoulomb of charge and a 38 ns fall against a 37 ns rise gives a soft recovery shape, which keeps the ringing on a 12 V rail inside the 60 V rating without a snubber.

Reverse recovery current of 2.8 A typical against a 34 A forward current is 8 per cent, and the 5.6 A maximum is the number that lands on the opposite switch in a bridge. A circuit that budgets on the typical figure and takes the rail to 55 V will see the maximum lot ring past 60 V at cold, which is why the derating on a 60 V part in a 48 V rail has to be argued on the maximum rows rather than the typical ones.

Where this part fits and where the next size up is cheaper

A 12 V 40 A synchronous rectifier, an OR-ing pair in a 1 kW redundant supply, a 24 V power tool stage at 60 A pulsed, and a 48 V battery disconnect all use the low on resistance and the 175 C junction well. In the battery disconnect the 5 mA of drain leakage at 175 C matters as much as the resistance, because a pack that sits for a month cannot afford a leakage path.

Above 60 A continuous in still air the arithmetic stops working: 3.75 W is the whole budget and the package is already at 32 W at the 150 A row. A customer who needs 100 A continuous in a sealed enclosure is better served by two devices in parallel with a shared heatsink or by a larger body, and the honest answer is to say so before a sample is booked.

Our power management cross reference work keeps the on resistance, the output charge and the gate resistance spread on file per approved alternate, because two 60 V parts at 1.45 milliohm can differ by a factor of ten in gate resistance and that difference decides whether a parallel pair shares current.

Questions we answer before a reel is booked

First, the gate drive. The on resistance is specified at 10 V and at 7.5 V and nowhere else, so a 5 V logic level driver is outside the published data even though the threshold window starts at 2 V. Drive at 7.5 V or above, and check the 43.6 nC of gate source charge against the driver, since 141 nC at 10 V and 200 kHz is 0.28 W of drive power.

Second, the avalanche row closes exactly: 180 mJ against 0.1 mH and 60 A is one half of 0.1 mH times 3600, and that is the printed figure. A repetitive avalanche in a motor drive can therefore be budgeted against it, provided the duty cycle stays inside the 1 per cent note that the row carries.

Third, the alternate. A 60 V part at 1.4 to 1.5 milliohm in TO-247 comes in several generations with different output charge, and the output charge is what a synchronous rectifier spends at every cycle. We hold it per approved alternate, the incoming inspection plan checks the lot against it, and the pin to pin comparison starts from the lead frame and the tab rather than from the outline drawing.