Contact Us

VBP112MC60-4L

Brand: VBsemi
VBsemi VBP112MC60-4L is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBP112MC60-4L — Discrete & Power Semiconductors | Superb Automation

VBP112MC60-4L

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBP112MC60-4L from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBP112MC60-4L: 1200 V and 60 A silicon carbide in a four lead TO247

The VBP112MC60-4L is the same 1200 V silicon carbide die as the three lead part, mounted in a TO247 four lead body that brings the source out on a separate pin for the gate return. Drain to source is 1200 V, the gate window is minus 10 V to plus 22 V, the threshold is 2 to 4 V, the printed drain current is 60 A and the on resistance is 40 milliohm at an 18 V gate.

The electrical table is identical to the three lead part and the difference is the package. A fourth lead carries the source connection for the gate loop, so the gate drive current does not share the source inductance with the power current. That single change removes most of the common source inductance that slows a fast turn on and lifts the gate at turn off.

At 60 A the die makes 144 W, at 30 A it makes 36 W, at 20 A it makes 16 W, at 10 A it makes 4 W. The current column is a die figure at a held case temperature. The package decides what the board can remove, and the four lead body is mechanically the same as the three lead one: one screw, one pad and the same footprint width.

Key data for the VBP112MC60-4L

ConfigurationSingle N channel
PackageTO247-4L, four leads with a separate source return
VDS1200 V
VGEMinus 10 V to plus 22 V
Vth2 to 4 V
ID60 A, a die figure at a 25 C case
RDS(on) at 18 V40 milliohm
TechnologySilicon carbide
Loss at 10 A4 W
Loss at 20 A16 W
Loss at 30 A36 W
Loss at 60 A144 W

What the fourth lead changes in the gate loop

In a three lead package the source pin carries the power current and the gate return at the same time. The inductance of that pin, in the region of 5 to 10 nanohenries, appears in series with the gate loop, and the voltage across it at a fast turn off opposes the gate drive. The result is a slower turn off, a longer time in the linear region and more loss, and at high dv/dt a gate that is pushed back up toward the threshold.

The four lead body separates the two paths. The gate return goes through its own pin, the common source inductance drops to a fraction of a nanohenry, and the gate sees the driver voltage rather than the driver voltage minus the source inductive drop. The turn off becomes faster and, more importantly, predictable, because it no longer depends on how much current the power path is carrying.

That matters most at 1200 V, where the drain swings the full bus in a few tens of nanoseconds and the Miller current is large. A part that switches cleanly at 10 A in a three lead body can ring at 40 A, and the same die in a four lead body behaves the same at both currents. The price is one more pad and a board where the return trace goes back to the driver rather than to the power ground.

Resistance, temperature and the size of the die

The 40 milliohm figure is a 25 C measurement at an 18 V gate. At 125 C the same die is 65 to 80 milliohm, so 30 A becomes 58 to 72 W and the heatsink has to be sized on that number rather than on the printed one. This is the single most common error in a silicon carbide circuit: the cold curve is quoted, the hot curve is what runs.

Driving at 18 V is part of reaching the printed figure. A 15 V drive leaves the channel partly enhanced and the resistance 30 to 50 per cent higher, which at 30 A is another 10 to 20 W. The gate window allows up to 22 V, so there is room for a 20 V drive with a small margin, and the usual choice is 18 V with a minus 3 to minus 5 V off bias.

The switching loss is the second term and at 1200 V it is not small. The energy in the output capacitance is lost at every hard turn on, and at 50 kHz it can add 3 to 6 W at 20 A. A soft switching topology removes it, and the four lead body is more often used in a resonant or a phase shifted bridge where the fast, clean edge is worth the extra pad.

Where the part fits and where it does not

It fits an 800 V battery inverter, a 690 V drive, a solar inverter at 1000 V, a charger for a high voltage battery, a phase shifted full bridge and an active front end at 20 to 30 A. It does not fit a 400 V bus where silicon is cheaper and lower loss, a 60 A continuous load in this body, or a board that cannot route the fourth lead back to the driver.

Where the part is offered as a replacement for a three lead code, the footprint is not the same and the driver return has to be reworked, so the change is a board revision rather than a part swap. Our how to verify a drop in replacement page covers what has to be checked when the package changes but the die does not.

The sourcing side of this part is covered on the date code management. For a four lead part held between builds, that page covers how the age is tracked and when the material is set aside.

Questions we get on this code

Is the die the same as the three lead part? On the printed table yes, and the package is what differs. The four lead body is chosen for the gate return, not for more current.

Does the fourth lead need a special socket? No. It is a through hole pin and the board needs one more pad and a trace back to the driver.

Can it be driven at 15 V? It can, and the resistance will be higher than printed. The 40 milliohm figure applies at 18 V.

What does the order carry? Part number with the 4L suffix, TO247-4L, and tube packing. We confirm the packing and the date code on the offer.