VBP1106
Product Specifications
VBP1106
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBP1106 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBP1106: 100 V and 150 A with 6 milliohm in a TO247
The VBP1106 is a single N channel MOSFET in a TO247 body rated at 100 V drain to source, plus or minus 20 V on the gate, a 3 V threshold, 150 A of drain current and 6 milliohm at a 10 V gate. The die is trench. The TO247 body is the one that can be bolted to a real heatsink with a single screw, which is why the 100 V class in this body is used for the main switch of a 48 V or 72 V converter rather than for an auxiliary circuit.
One hundred volts holds a 48 V pack at 54 V with a large margin, a 72 V pack at 84 V with a workable one, and a 60 V bus with room for a switching spike. It is the class where a 48 V system stops paying for margin it does not need and a 72 V system starts to need it.
Six milliohm at 150 A is 135 W, at 60 A it is 21.6 W, at 40 A it is 9.6 W, at 20 A it is 2.4 W. A TO247 on a 1 C per watt heatsink holds 40 to 60 W with a reasonable sink temperature, so 40 to 60 A continuous is a real operating point in this body.
Key data for the VBP1106
| Configuration | Single N channel |
| Package | TO247, bolted to a heatsink |
| VDS | 100 V |
| VGS | Plus or minus 20 V |
| Vth | 3 V typical |
| ID | 150 A, a die figure at a 25 C case |
| RDS(on) at 10 V | 6 milliohm |
| Technology | Trench |
| Loss at 20 A | 2.4 W |
| Loss at 40 A | 9.6 W |
| Loss at 60 A | 21.6 W |
| Loss at 150 A | 135 W |
Why the TO247 changes the arithmetic
A TO247 die is larger than a TO220 die, and the package is built for a screw and a thermal pad against a metal sink. The junction to case figure is around 0.5 to 0.7 C per watt, so 21.6 W at 60 A lifts the die 11 to 15 C above the case, and a case at 90 C leaves the junction at 105 C. That is a working point, not a limit.
The same die in a TO220 would be at 30 C above the case for the same watts and the sink would have to be cooler. The package is the reason a 100 V part can carry 60 A in a product and the reason the same silicon in a smaller body cannot.
Mounting matters as much as the package. A thermal pad of 0.2 mm at 1 C per square centimetre, a clean surface and the specified torque are worth 10 C. A dry joint, a burr or an over tightened screw is worth a field failure, and the TO247 with its single screw and large contact area is more forgiving than a clip in a smaller body.
Switching loss in a 48 V converter
At 48 V and 40 A with a 30 ns crossover the overlap loss is about 0.6 W per transition at 100 kHz, so 1.2 W for the pair of edges, against 9.6 W of conduction. The part is conduction limited, which means the frequency can be raised to shrink the inductor without the switch becoming the limit, up to the point where the output capacitance term takes over.
The output capacitance at 100 V for a die of this size is a few nanofarads, and the energy stored is lost at every turn on in a hard switched converter. At 200 kHz that term reaches a couple of watts, which is still small against 9.6 W. At 400 kHz it becomes comparable, and the topology rather than the device decides whether the loss is acceptable.
The body diode is a factor in a synchronous buck. Its forward drop during the dead time at 40 A is around 0.8 V, which is 32 W for the duration, so the dead time has to be short and the driver has to hold the low side off only as long as the diode needs. A 20 ns dead time at 200 kHz costs about 0.13 W, which is negligible; a 200 ns dead time costs 1.3 W, which is not.
Where the part fits and where it does not
It fits a 48 V to 12 V synchronous buck at 30 to 50 A, a 72 V motor driver, a battery disconnect on a 72 V pack, an inverter stage in a small drive, a welding supply and a charger output stage. It does not fit a 400 V bus, a 150 A continuous load, or a board with no heatsink at 60 A.
Where several 100 V codes are on one BOM, this part is a candidate for consolidation because the TO247 body covers a wide current range and the heatsink interface is common. Our power management cross reference page covers how the codes are compared on resistance, charge and thermal path before one is kept.
The sourcing side of this part is covered on the vendor consolidation. For a 100 V part that several products share, that page covers which lines stay dual sourced after a consolidation.
Questions we get on this code
Is 150 A usable? No. At that current the die makes 135 W and no practical sink holds it. Forty to sixty amps is the working range with a normal extrusion.
Is 100 V enough for a 72 V pack? At 84 V full charge, yes with a clamp and a short loop. A 120 V part gives more margin for a switching spike.
Does it need an insulator? If the sink is grounded, yes, with a thermal pad and a shoulder washer. If the sink is isolated, the tab can be bolted dry with grease.
What does the order carry? Part number, TO247, and tube packing. We confirm the packing and the date code on the offer.