Contact Us

VBNCB1206

Brand: VBsemi
VBsemi VBNCB1206 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBNCB1206 — Discrete & Power Semiconductors | Superb Automation

VBNCB1206

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBNCB1206 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBNCB1206: a 20 V die, a 30 V row and a 90 A lead limit

The VBNCB1206 is a low voltage N channel trench MOSFET in the TO-262 body, 3 milliohm at a 10 V gate, 7 milliohm at 4.5 V, and a 95 A continuous row that carries a package limited note of 90 A. It is built for OR-ing, server rails and DC to DC converters, which is to say for a 12 V or 20 V bus where the switch is in the main current path.

The first line of the sheet reads 20 V and the absolute maximum table reads 30 V for drain to source. The breakdown row then prints 20 V minimum. Those three cannot all describe the same limit, and the reading that survives is a 20 V device with a 30 V non repetitive ceiling printed in the wrong row. For a 12 V rail with a 20 percent transient the 20 V figure is the one to work to.

The second inconsistency is the current. The product summary prints 95 A, the absolute maximum table prints 95 A with a package limited note, and the same note states that the package limitation is 90 A. A purchase order that names 95 A is asking for a current the leads cannot guarantee.

The parameter table in full

Drain to source voltage in the title and the breakdown row20 V
Drain to source voltage in the absolute maximum row30 V, not consistent with the breakdown
Gate to source voltage, continuousplus or minus 20 V
On resistance at 10 V gate and 20 A0.0030 ohm typical
On resistance at 4.5 V gate and 20 A0.0070 ohm typical
Gate threshold at 250 microamp0.5 V minimum, 2.5 V maximum
Continuous drain current, case at 25 C and 70 C95 A and 65 A, package limited to 90 A
Continuous drain current, ambient at 25 C and 70 C for 10 s28.8 A and 27 A
Pulsed drain current300 A
Avalanche current into 0.1 mH36 A
Single pulse avalanche energy104 mJ
Maximum power dissipation, case at 25 C and 70 C250 W and 175 W
Maximum power dissipation, ambient at 25 C and 70 C3.75 W and 2.63 W
Junction to ambient for 10 s32 C per watt typical, 40 maximum
Junction to case, steady state0.5 C per watt typical, 0.6 maximum
Operating junction and storage rangeminus 55 to plus 175 C
Zero gate voltage drain current at 20 V and at 55 C1 and 10 microamp
On state drain current at a 10 V gate90 A
Forward transconductance at 28.8 A160 S
Input, output and reverse transfer capacitance at 15 V4000, 1725 and 970 pF
Total gate charge at 10 V gate and 28.8 A171 nC typical, 257 maximum
Total gate charge at 4.5 V gate and 28.8 A81.5 nC typical, 123 maximum
Gate source and gate drain charge34 and 29 nC
Gate resistance1.4 ohm typical, 2.1 maximum
Turn on delay and rise time at a 10 V gate, 24 A18 and 11 ns typical, 27 and 17 maximum
Turn off delay and fall time at a 10 V gate70 and 10 ns typical, 105 and 15 maximum
Turn on delay and rise time at a 4.5 V gate, 22.5 A55 and 180 ns typical, 83 and 270 maximum
Body diode forward drop at 22 A0.8 V typical, 1.2 V maximum
Body diode recovery time, charge and peak current52 and 78 ns, 70.2 and 105 nC

The 4.5 V gate row is where the loss hides

At 10 V and 20 A the loss is 1.2 W. At 4.5 V and 20 A it is 2.8 W, which is 2.3 times more. In a 12 V server rail driven from a 5 V logic supply through a slow level shifter, the part can spend its life at the 4.5 V row, and the thermal budget written for 3 milliohm is then 30 percent short.

The switching rows repeat the message: at a 10 V gate the turn on delay is 18 ns and the rise 11 ns, while at 4.5 V they are 55 ns and 180 ns. The 270 ns maximum rise at 4.5 V is slower than the switching period at 1 MHz, which is why this part belongs on a 10 V driver in any converter above 200 kHz.

The gate charge drops with the gate level as well, 171 nC at 10 V against 81.5 nC at 4.5 V, and the product summary prints 82 nC as its typical. That figure belongs to the 4.5 V row, not to the 10 V row, so a driver sized from the summary at a 10 V gate is undersized by a factor of two.

Thermals: 250 W on the tab, 3.75 W in air

The 250 W row at a 25 C case and 0.5 C per watt typical give a 125 C rise, which fits the 175 C junction. At 65 A and a 70 C case the resistance at temperature is roughly 4.4 milliohm, so the loss is 18.6 W and the case rise is 9 C. At 90 A the loss is 36.5 W at 25 C resistance and 54 W at the hot value, which is what makes the lead limit of 90 A a thermal number as much as a mechanical one.

In still air the 40 C per watt maximum allows 3.75 W for the 150 C rise, which is 35.4 A at 25 C resistance and 25 A at the hot value. That is a large still air current for a leaded body and it comes from the 3 milliohm die.

The 10 s ambient rows of 28.8 A and 5 W dissipation belong to the one inch square board test and not to a steady state product. A customer who quotes 28.8 A for a sealed enclosure has read the wrong row, and the 3.75 W row is the one to use.

Where a 20 V, 3 milliohm switch belongs

A 12 V server rail with OR-ing diodes replaced by FETs, a point of load converter for a 1.2 V core rail, a battery disconnect on a 3 cell pack and a synchronous rectifier in a 5 V output all fit. In each case the switch carries the full load current and the 3 milliohm is the whole loss budget.

For a 20 A rail the loss at 10 V is 1.2 W and the part is cool on a modest pour. For a 60 A rail the loss is 10.8 W and the tab has to be on metal. The 90 A lead limit is the ceiling for a single device whatever the copper does.

Where a customer is comparing this part with a 30 V device of the same resistance, the choice is set by the transient, not the nominal rail. A 12 V rail with a 24 V clamp event needs a 30 V part; a regulated 12 V rail with a suppressor fits the 20 V die. Our power management cross reference work records the clamp level and the resistance at both gate levels for every alternate, because those two decide the substitution.

Questions we answer before a reel is booked

First, the voltage. Ask the supplier which row is the rating: the 20 V title and breakdown, or the 30 V absolute maximum. Our reading is a 20 V device, and we do not quote it into a rail that can ring above 22 V without a suppressor.

Second, the current. The package limit is 90 A, printed in a note, while the tables print 95 A. Quote 90 A, and ask for the lead temperature at that current before committing a production schedule.

Third, the second source. 20 V parts at 3 milliohm differ in the resistance at 4.5 V, which is the row that a 5 V driven rail actually uses. The incoming inspection plan and the verification steps for a drop in replacement measure the 4.5 V resistance and the threshold window, since a part that matches at 10 V can be 40 percent worse at 4.5 V.