Contact Us

VBMB17R15SE

Brand: VBsemi
VBsemi VBMB17R15SE is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBMB17R15SE — Discrete & Power Semiconductors | Superb Automation

VBMB17R15SE

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBMB17R15SE from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBMB17R15SE: 700 V at 0.260 ohm for the rail that a 650 V part cannot hold

The VBMB17R15SE is a 700 V N channel super junction MOSFET in the TO-220F isolated body, 0.260 ohm at a 10 V gate, 15 A continuous at a 25 C case. The extra 50 V over a 650 V part exists for one reason: a 400 V bus that rings, or a three phase input that regenerates, can push a 650 V device past its rating on a hot day, and the next step up is cheaper than the clamp.

The sheet sits between two siblings in the same family and the placement is deliberate. The 650 V VBMB165R42SFD gives 0.056 ohm and a 90 ns diode. The 800 V VBMB18R15S gives 0.38 ohm. This part gives 0.26 ohm at 700 V, which is the middle of both axes, and the on resistance is specified at only 5 A, which says the die is small and the thermal path is the limit.

The applications list is the usual one for the family: server and telecom supplies, switch mode supplies, power factor correction, lighting and industrial. For a 380 V three phase rectified bus, which reaches 540 V before any margin, 700 V leaves 160 V and 650 V leaves 110 V. The difference matters in a 5 kW stage with 200 nH of loop inductance.

The parameter table in full

Drain to source voltage at maximum junction temperature700 V
Gate to source voltage, continuousplus or minus 30 V
On resistance at 10 V gate and 5 A, 25 C0.260 ohm typical
Gate threshold at 250 microamp2.5 V minimum, 4.5 V maximum
Continuous drain current, case at 25 C and 100 C15 A and 9 A
Pulsed drain current, repetitive45 A
Single pulse avalanche energy, 28.2 mH and 5 A start600 mJ
Maximum power dissipation, case at 25 C90 W
Linear derating factor1.67 W per C
Junction to case and junction to ambient0.7 and 62 C per watt
Operating junction and storage rangeminus 55 to plus 150 C
Drain source voltage slope, junction at 125 C50 V per ns
Reverse diode voltage slope15 V per ns
Input, output and reverse transfer capacitance1790, 80 and 4 pF
Effective output capacitance, energy and time related63 and 213 pF
Total, gate source and gate drain charge76, 15 and 19 nC
Turn on delay and rise time at 520 V and 8 A18 and 24 ns typical, 25 and 55 ns maximum
Turn off delay and fall time, same conditions80 and 12 ns typical
Gate input resistance0.8 ohm
Continuous and pulsed source drain diode current15 and 45 A
Body diode forward drop at 8 A1.5 V maximum
Body diode recovery time, charge and peak current80 ns, 5.8 microcoulomb and 31 A
Forward transconductance at 5 A5.6 S
Peak soldering temperature for 10 s260 C

Half the on resistance of an 800 V part, one third of the loss

At 0.26 ohm the conduction loss at 8 A is 16.6 W, which needs a case below 138 C through the 0.7 C per watt path. At the 15 A rating the loss is 58.5 W and the case has to stay under 109 C, which is a heatsink rather than a tab. At a 1 A standby load the loss is 0.26 W and the part is cool in any package.

Compared with the 800 V VBMB18R15S at 0.38 ohm, this part saves 32 percent of the conduction loss for the same current and gives up 100 V of rating. Compared with the 650 V VBMB165R42SFD at 0.056 ohm it gives up 4.6 times the resistance in exchange for the extra 50 V. A 700 V part is only worth its resistance when the rail genuinely needs 700 V, and that is a question about the clamp and the surge, not about the nominal bus.

In still air the 62 C per watt row allows 2.02 W, which is 2.79 A at 25 C. That is the honest continuous figure for a board with no heatsink, and it is one fifth of the headline rating. When a customer asks whether a 15 A part can carry 6 A on a small tab, the answer is that 9.4 W needs the case under 143 C, which a tab in still air will not hold.

The diode, the gate and the avalanche row

The recovery row reads 80 ns with 5.8 microcoulomb and 31 A of peak reverse current, which is faster than the 600 V plain member at 475 ns and slower than the 650 V fast diode member at 90 ns. For a hard switched half bridge at 50 kHz the recovery charge is what heats the opposite switch, and 5.8 microcoulomb at 50 kHz and 400 V is 0.116 W of loss in the diode itself, before the spike is counted.

Gate charge is 76 nC at a 10 V gate, which at 50 kHz costs 0.038 W of drive. The internal gate resistance of 0.8 ohm means the external resistor sets the switching edge, and the printed 18 ns delay with a 24 ns rise at 8 A says the part is not slow; the 80 ns turn off delay is the larger term and it comes from the miller plateau at this voltage.

The avalanche row prints 600 mJ against a 5 A start into 28.2 mH, which stores 352 mJ. As on the other sheets of this family, the printed energy is larger than the stated test can store, so the row cannot be used to size a clamp. Where a flyback or a relay driver depends on avalanche, ask for the test report and run the repetitive curve for the actual leakage inductance.

Where 700 V earns the extra 50 V

A three phase 380 V input rectifies to 540 V and a regenerating motor can push a 400 V bus to 450 V. With 650 V the margin is 110 V or 200 V, and a 50 nH loop with 20 A per microsecond of di/dt produces 100 V of spike on its own. Moving to 700 V buys the margin without changing the gate drive, the footprint or the heatsink, which is the cheapest change in the whole power stage.

It is also the right step for a supply that has to hold up at a low line with a long holdup requirement, and for equipment sold into a market where the surge test is severe. In both cases the extra voltage is not about the nominal bus; it is about the worst ten microseconds of the year.

Where a customer is moving from a 650 V trench part to this device, the change in drive is small and the change in diode is not. Our power management cross reference work compares two switches on the diode, the threshold window and the thermal pair, because at 700 V those three decide whether the replacement survives the first surge.

Questions we answer before a reel is booked

First, the current at which the resistance was measured. 0.26 ohm at 5 A is a small die figure, and at 9 A the resistance rises with temperature: a die at 125 C carries roughly 1.6 times its 25 C value, so 0.42 ohm at 9 A is 34 W, not 21 W. Size the heatsink from the hot value.

Second, the threshold. A 4.5 V maximum threshold leaves 1.5 V of margin on a 6 V driver that sags, so drive from 10 V, and remember that the threshold climbs as the die cools. A cold start in a garage in winter is the worst case for a marginal driver.

Third, the second source. 700 V parts at 0.26 ohm are made by several suppliers, and the diode recovery and the threshold window differ more than the resistance does. The verification steps for a drop in replacement and the lead time work hold those rows per approved alternate, so a proposed substitute is compared on behaviour and not on a label.