VBMB16R15S
Product Specifications
VBMB16R15S
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBMB16R15S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBMB16R15S: 600 V and 15 A with 280 milliohm in a TO220F
The VBMB16R15S is a single N channel MOSFET in a TO220F body rated at 600 V drain to source, plus or minus 30 V on the gate, a 3.5 V threshold, 15 A of drain current and 280 milliohm at a 10 V gate. The die is SJ multiple epitaxy. This is the entry point of the 600 V class in the TO220F body, and it is the part that fits a converter below about 100 W.
Two hundred and eighty milliohm is a modest figure for 600 V and it is the right one for a low power circuit. At 15 A the die makes 63 W, at 6 A it makes 10 W, at 4 A it makes 4.5 W, at 2 A it makes 1.1 W. The usable range in a plastic tab with a small heatsink is 2 to 5 A, which is exactly where a standby supply, a bias rail and a relay driver live.
Six hundred volts holds a 400 V bus with 200 V of margin and a 230 V AC line at 325 V after rectification with room for a 300 V transient. It does not hold a 480 V line at 680 V, and it does not hold a 400 V bus during a regeneration event that lifts the rail above 500 V without a clamp.
Key data for the VBMB16R15S
| Configuration | Single N channel |
| Package | TO220F, isolated plastic tab |
| VDS | 600 V |
| VGS | Plus or minus 30 V |
| Vth | 3.5 V typical |
| ID | 15 A, a die figure at a 25 C case |
| RDS(on) at 10 V | 280 milliohm |
| Technology | SJ multiple epitaxy |
| Loss at 2 A | 1.1 W |
| Loss at 4 A | 4.5 W |
| Loss at 6 A | 10 W |
| Loss at 15 A | 63 W |
Where a low current 600 V part is the right buy
A bias supply in a motor drive draws 200 to 500 mA at 15 V and the switch carries a fraction of an amp at 400 V. A part of this class at 2 A loses 1.1 W, which a small copper island removes with the junction at 90 C. A larger die at 80 milliohm would lose 0.3 W and cost three times as much, and the 0.8 W saving would not change the board.
The same logic applies to a start up circuit, a bleeder, a relay driver on a high rail, and the active clamp of a flyback below 50 W. These circuits are chosen by voltage and by the ability to survive a surge, and the current is an afterthought. Paying for a low resistance die in a 0.3 A circuit is the most common waste in a high voltage BOM.
The place where it stops being true is a continuous mode power factor stage. There the switch carries several amps for most of the period and the conduction term dominates, so the resistance has to be bought. The boundary is around 3 A root mean square at 65 kHz; below it this part is fine, above it the next die up pays for itself.
Switching loss and the 65 kHz boundary
At 600 V and 2 A the crossover loss at 65 kHz with a 15 ns transition is about 0.1 W, which is small against 1.1 W of conduction. At 100 kHz it doubles to 0.2 W, still small. The term that grows faster is the output capacitance, which is charged and discharged once per cycle and does not care about the current. At 150 kHz in a discontinuous converter that term can exceed the conduction loss at 2 A.
The gate charge is the other half. A 600 V die of this size needs about 10 to 15 nanocoulombs, which a small driver fills in 20 ns with 0.5 A. That is the reason this class works with a simple driver and no negative rail, provided the gate loop is short and the Miller current at turn off is absorbed by a resistor close to the pin.
At the top of the current range the picture changes. At 6 A the conduction loss is 10 W and the switching term at 65 kHz is 0.3 W, so the part is still conduction limited, and the thermal path decides. Above 6 A the plastic tab is the limit before the die is.
Where the part fits and where it does not
It fits an auxiliary supply on a 230 V or 400 V rail, a start up circuit, a relay or contactor driver on a high rail, a bleeder, an active clamp below 50 W, and a small power factor stage below 100 W. It does not fit a 20 A motor drive, a 480 V AC input, or a converter above 150 kHz at more than 3 A.
When a customer is consolidating high voltage codes, this part often replaces three or four low current parts of different voltages, and the check is that the highest voltage in the group stays inside the margin of the lowest rated device. Our pin to pin cross reference page covers how a family is compared before the codes are merged.
The sourcing side of this part is covered on the strategic sourcing. For a low current part that sits on many boards, that page covers how one code is held across the product range.
Questions we get on this code
Is 280 milliohm too high for a switching supply? At 2 to 4 A it is the correct figure and it costs less than a low resistance die. Above 6 A it becomes the limit.
Can it be used at 400 V DC? Yes, with 200 V of margin. Add a clamp so a regeneration event cannot lift the drain above about 500 V.
Does the isolated tab need a heatsink? Above about 3 W yes. Below that a copper island on two ounce copper is enough.
What does the order carry? Part number, TO220F, tube packing, and the date code. We confirm both on the offer.