Contact Us

VBMB1254N

Brand: VBsemi
VBsemi VBMB1254N is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBMB1254N — Discrete & Power Semiconductors | Superb Automation

VBMB1254N

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBMB1254N from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBMB1254N: a 250 V N channel part in the isolated full pack body

The VBMB1254N is an N channel MOSFET rated 250 V drain to source with a plus or minus 20 V gate, supplied in the TO-220 full pack body, which is the moulded version with an isolated tab. Continuous drain current is 40 A with the case at 25 C and 33 A with it at 100 C, and on resistance is 0.040 ohm at a 10 V gate and 11 A.

250 V is the class between the 200 V parts used on a 110 V mains rectified rail and the 400 V to 650 V parts used on a power factor stage. In practice it is a telecom and industrial part: a 48 V or 110 V rail with a flyback or a push pull, a battery disconnect, a low voltage motor bridge. The full pack body is chosen when the tab cannot be live, which is most of the time in a product with a metal chassis.

The data sheet carries a note on page two that the conditions are taken from the IRF640 and SiHF640 documents, which tells a buyer something useful: the electrical table is derived from a long established 200 V family and the part is a 250 V extension of it. That is normal in this band, and it also means the condition rows should be read as inherited rather than freshly measured.

The parameter table

Drain to source voltage250 V
Gate to source voltageplus or minus 20 V
On resistance at 10 V gate, 11 A0.040 ohm
Gate threshold at 250 microamp2.0 V to 4.0 V
Continuous drain current, case at 25 C and 100 C40 A and 33 A
Pulsed drain current150 A
Single pulse avalanche energy, 2.7 mH, 18 A start580 mJ
Avalanche current and repetitive avalanche energy20 A and 13 mJ
Power dissipation rows as printed, 25 C3.1 W and 130 W
Junction to case and junction to ambient1.0 and 40 C per watt
Linear derating factor1.0 W per C
Operating junction and storage rangeminus 55 to plus 150 C
Breakdown voltage temperature coefficientminus 0.29 V per C
Zero gate voltage drain current at 200 V25 microamp maximum
Zero gate voltage drain current at 160 V, 125 C250 microamp maximum
Input, output and reverse transfer capacitance1300, 430 and 130 pF
Total gate charge maximum at 160 V, 20 A70 nC
Gate source and gate drain charge13 and 39 nC
Turn on delay and rise time14 and 51 ns typical
Turn off delay and fall time45 and 36 ns typical
Body diode forward drop at 20 A2.0 V maximum
Body diode recovery time, typical and maximum300 and 610 ns
Body diode recovery charge, typical and maximum3.4 and 7.1 microcoulomb
Peak diode recovery slope5.0 V per ns
Soldering peak temperature for 10 s300 C

Two dissipation rows that were printed the wrong way round

Page one prints 3.1 W against a case temperature of 25 C and 130 W against an ambient of 25 C. Those two cannot both be true: a heatsinked case is always the better thermal path than free air. The junction to case figure of 1.0 C per watt and the junction to ambient figure of 40 C per watt settle it. At a 150 C junction and a 25 C case the allowed rise is 125 C, and 125 divided by 1.0 gives 125 W, which is close to the 130 W printed in the ambient row. In still air, 125 divided by 40 gives 3.1 W, which is exactly the figure printed in the case row.

So the labels are swapped and the numbers are right. A buyer quoting 130 W as a still air figure would be out by a factor of forty. This is the kind of typographical fault that survives a data sheet review and then appears in a customer's thermal calculation, and it is worth flagging to the supplier rather than passing on.

With the rows read correctly, the part carries 40 A through 0.040 ohm for 64 W, which is a 64 C rise to the case on the full pack tab. That is a real heatsink, and the isolation layer inside the body already removes the need for an insulating pad, which is the reason to choose the full pack in the first place.

What 130 pF of reverse transfer tells you

The reverse transfer capacitance of 130 pF is high for a 250 V part, and it pairs with a 39 nC gate drain charge against 70 nC of total gate charge, which means more than half the gate charge is spent crossing the plateau. That produces a slow, controlled edge at 5 V per ns of diode recovery slope and a 51 ns rise time, both of which are gentle on EMI and expensive on switching loss. A 250 V part in this body is a 50 kHz to 100 kHz device, not a 300 kHz one.

The 300 ns to 610 ns body diode recovery is the other inherited trait. For a bridge at 100 kHz that is a real loss term; for a flyback primary, where the diode never conducts, it costs nothing. The application decides whether the row matters, and the row itself does not change.

The threshold of 2.0 V to 4.0 V is wide, which is normal for a trench part of this generation and means a 4.5 V drive is marginal at low temperature. Drive it at 10 V, and check the gate resistor against the 51 ns rise, because a larger resistor turns the switching loss into heat in the channel.

Where the full pack body is the deciding feature

A TO-220 full pack has a moulded body over the tab, so the tab is isolated to about 2.5 kV and can be bolted straight to a chassis or a shared heatsink without a mica washer. That saves a assembly step and, more importantly, it removes the thermal resistance of the pad. The trade is that the moulding adds its own resistance, which is why the 1.0 C per watt figure is worth confirming on the qualification sample rather than assumed from a bare tab part.

In a 48 V telecom rectifier, the secondary side sees 100 V to 150 V and the primary sees 400 V, so a 250 V part belongs on the intermediate rail, the battery disconnect or the synchronous rectifier clamp. In a 110 V mains product the rectified rail is 170 V and a 250 V part leaves 47 per cent margin, which is the textbook place for it.

When a customer replaces a 200 V part with this one to gain margin, the on resistance rises by about 30 per cent at the same die size and the gate charge rises with it. Our obsolete part cross reference records both, and the strategic sourcing work uses the derived document note to set the inspection level, since a table inherited from another family deserves a first article measurement.

On a 110 V mains input the rectified rail sits at 170 V, and a 20 per cent surge takes it near 205 V, so a 250 V part leaves 45 V of headroom for the leakage spike. On a 48 V telecom rail the part is heavily derated and the 0.040 ohm is the whole story: 20 A gives 16 W and a heatsink, 10 A gives 4 W and a pad. Between those two points the same part covers a product line, which is why it stays in catalogues long after the 200 V family it was derived from.

Questions before a reel is booked

First, the dissipation rows. Confirm in writing which row is the case figure and which is the ambient figure, because the printed labels are reversed.

Second, the derivation note. The conditions are taken from the IRF640 and SiHF640 documents, so ask which rows were measured on this die and which were carried across.

Third, the package. A full pack is not interchangeable with a bare tab part on a heatsink, and the isolation voltage is the reason to buy it. The launch checklist records the tab isolation and the mounting torque before the first build.