VBM18R15S
Product Specifications
VBM18R15S
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBM18R15S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBM18R15S: one document, three bodies, 800 V at 0.38 ohm
The VBM18R15S is an 800 V N channel super junction MOSFET rated 15 A continuous with the case at 25 C and 0.38 ohm at a 10 V gate. The document covers three order strings in three bodies: the VBM in TO-220AB, the VBMB in TO-220 full pack and the VBP in TO-247AC. That is worth knowing before a purchase order is raised, because the electrical table is common and the thermal path is not.
800 V is the class for a 480 V three phase bus with real surge margin, for a solar string input, or for a power factor stage that has to survive a 6 kV ring wave. At 0.38 ohm the part is a low current device, 15 A at a 25 C case and 12 A at 100 C, and its natural home is the primary side of a 300 W to 1 kW converter running at 40 kHz to 100 kHz.
The sheet prints 48 nC typical and 96 nC maximum of gate charge, a 297 mJ single pulse avalanche rating at a 4.5 A start, and a 325 ns body diode recovery. Those three rows describe a part that is fast at the gate, modest in avalanche and slow in the diode, which is the usual shape of a low current high voltage super junction device.
The parameter table
| Drain to source voltage, all three bodies | 800 V |
| Gate to source voltage | plus or minus 30 V |
| On resistance at 10 V gate, 8 A, 25 C | 0.38 ohm maximum |
| Gate threshold at 250 microamp | 2 V minimum, 4 V maximum |
| Continuous drain current, case at 25 C and 100 C | 15 A and 12 A |
| Pulsed drain current | 46 A |
| Single pulse avalanche energy, 28.2 mH, 4.5 A start | 297 mJ |
| Power dissipation, case at 25 C | 208 W |
| Junction to case and junction to ambient | 0.7 and 62 C per watt |
| Linear derating factor | 1.7 W per C |
| Operating junction and storage range | minus 55 to plus 150 C |
| Breakdown voltage temperature coefficient | minus 0.75 V per C |
| Zero gate voltage drain current at 800 V | 1 microamp maximum |
| Zero gate voltage drain current at 520 V, 125 C | 10 microamp maximum |
| Input, output and reverse transfer capacitance | 1720, 80 and 4 pF |
| Effective output capacitance, energy and time related | 63 and 213 pF |
| Total gate charge, typical and maximum | 48 and 96 nC |
| Gate source and gate drain charge | 11 and 21 nC |
| Turn on delay and rise time | 18 and 24 ns typical |
| Turn off delay and fall time | 48 and 25 ns typical |
| Gate input resistance | 0.8 ohm typical |
| Body diode forward drop at 8 A | 1.2 V maximum |
| Body diode recovery time and charge | 325 ns and 4.6 microcoulomb |
| Body diode peak reverse recovery current | 20 A |
| Drain source voltage slope at 125 C | 37 V per ns |
| Soldering peak temperature for 10 s | 300 C |
Three bodies, one electrical table, three thermal answers
The electrical table is printed once and applies to the VBM, the VBMB and the VBP. What it does not change is the junction to case figure, which is printed as 0.7 C per watt for all three, and that is the row a thermal engineer should question first. A full pack body with a moulded isolation layer normally adds thermal resistance between the die and the tab, and the printed value here is the same as the bare tab part. The value may be a placeholder carried across from the parent document, and it is worth asking for the part specific figure before a heatsink is sized.
The same caution applies to the 208 W dissipation row, which is 29 W above the 178.6 W that 0.7 C per watt supports at a 150 C junction with a 25 C case. Where a printed dissipation exceeds the thermal pair, the thermal pair is the limit and the dissipation row is a package capability. Two rows cannot both be used as a constraint, and the one that survives an audit is the pair.
On the board the part carries 8 A at 0.38 ohm for 24 W, which is a 17 C rise to the case and a 10 C per watt heatsink that holds the junction near 120 C at a 60 C ambient. In still air, 62 C per watt supports 2.02 W at 25 C and 1.61 W at 50 C, equal to 2.30 A and 2.06 A. An 800 V part in still air is a 2 A device, whatever the 15 A row says.
The slow diode, and why it is acceptable here
325 ns of recovery with 4.6 microcoulomb of charge and 20 A of peak reverse current is slow by super junction standards, and in a hard commutated bridge it would cost real loss. In the applications this part is used for, the diode rarely conducts: a flyback primary never reverse biases the body diode, and a power factor stage with continuous conduction uses the boost diode rather than the switch diode. Where the diode does conduct, the 20 A peak is modest and the 4.6 microcoulomb is small, so a snubber is not needed at 100 kHz.
The 37 V per ns drain source slope is the slowest among the super junction parts in this shipment, which pairs with the slow diode and makes the part the gentlest of the family on EMI. A 600 V bus crossed in 16 ns with 20 nH of loop inductance produces about 0.74 V of overshoot per amp of current step, which is the kind of number that keeps a 6 kV ring wave test inside the clamp.
Where 800 V is the right class
A 480 V three phase supply with a 680 V bus and a 20 per cent surge takes a 800 V part without a clamp discussion. A solar string at 600 V to 700 V open circuit is the same argument. A single phase 400 V bus does not need 800 V and should use the 650 V family, where 0.085 ohm is available at more than double the current.
Where a customer has an existing 800 V board and the original part is going away, the replacement has to match the three bodies, since a VBM and a VBMB are not interchangeable on a heatsink even though the electrical table is identical. Our last time buy work records which body is on the board before the last order is placed, and the power management cross reference keeps the three order strings apart on purpose.
A 800 V rating against a 680 V bus is 15 per cent margin, which is less than it sounds when the supply rings above 750 V at light load. The 297 mJ avalanche figure covers a single event and the 10 microamp leakage at 520 V and 125 C is a hundred times the cold figure. Both rows describe a part that is comfortable at 5 A and marginal at 12 A, which is why the same body is offered at three current levels and the middle one is usually the right purchase.
Questions before a reel is booked
First, which body. The VBM, the VBMB and the VBP share a table and not a footprint, and the full pack adds isolation that a heatsink assembly may depend on. Confirm the body and the tab style before the order.
Second, the thermal pair. Ask for the part specific junction to case figure on the body that will be used, and treat 208 W as a package capability rather than a limit.
Third, the hot leakage. 10 microamp at 520 V and 125 C is small, but it is one hundred times the room temperature figure, so the test has to be hot. We record it with the supplier onboarding file so a new lot is compared against the same condition.