VBM18R06S
Product Specifications
VBM18R06S
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBM18R06S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBM18R06S: 800 V and 6 A with 800 milliohm in a TO220
The VBM18R06S is a single N channel MOSFET in a TO220 body rated at 800 V drain to source, plus or minus 30 V on the gate, a 3.5 V threshold, 6 A of drain current and 800 milliohm at a 10 V gate. The die is listed as SJ multiple epitaxy, which is the charge balance structure that makes 800 V possible in a body this small.
Eight hundred volts is a class chosen by the mains and by the surge, not by the load. A 400 V DC bus with a 100 V margin, a 230 V AC line at 325 V after rectification with room for a 500 V transient, a 480 V three phase line at 680 V after rectification, a flyback reflected voltage plus its clamp. The part is not chosen for the current, it is chosen for the voltage, and the current follows.
Six amps at 800 milliohm is 28.8 W, which no TO220 can hold. Three amps is 7.2 W, two amps is 3.2 W, one amp is 0.8 W. This is a part for the auxiliary supply and the standby rail, not for the main power path.
Key data for the VBM18R06S
| Configuration | Single N channel |
| Package | TO220, through hole with the tab on the drain |
| VDS | 800 V |
| VGS | Plus or minus 30 V |
| Vth | 3.5 V typical |
| ID | 6 A, a die figure at a 25 C case |
| RDS(on) at 10 V | 800 milliohm |
| Technology | SJ multiple epitaxy |
| Loss at 1 A | 0.8 W |
| Loss at 2 A | 3.2 W |
| Loss at 3 A | 7.2 W |
| Gate drive | 10 V on, and the gate window allows a negative off bias |
Where 800 V is the right class and where it is not
Eight hundred volts suits a flyback on a 230 V AC input with a reflected voltage around 120 V and a clamp that lets the drain reach 600 V on a bad day, and it suits a power factor stage on a 480 V line. It does not suit a 400 V DC bus in a well behaved converter, where a 600 V part is cheaper and has a lower resistance at the same die size, and it does not suit a 690 V line where the peak reaches 975 V.
The margin rule is simple and it is not the marketing rule. Take the highest voltage the drain will see in any condition, including the clamp, the surge and the recovery of the diode in the opposite leg, and keep 15 to 20 per cent between that number and 800 V. A part run at 780 V survives the bench and fails in the field on the first lightning surge.
Below that ceiling the trade is resistance against voltage. At the same die area, an 800 V charge balance die has roughly twice the resistance of a 600 V part, which is why this part prints 800 milliohm where a 600 V part of the same body prints about 400. That is the price of the extra 200 V and it is paid on every conduction cycle.
Switching loss at this resistance level
At 6 A the conduction loss is already 28.8 W, so the part is only sensible at 1 to 3 A, where conduction is 0.8 to 7.2 W. In that range switching loss can be comparable. A 65 kHz flyback with a 400 V drain swing and a 10 ns crossover dissipates roughly 0.15 W per amp of current in the crossover, so two amps add about 0.3 W on top of 3.2 W.
The output capacitance matters more than the crossover time on a high voltage part because the energy stored in it is lost at every turn on in a discontinuous converter. A charge balance die at 800 V holds a small charge for its voltage but the voltage is high, so the loss is not negligible at 100 kHz. Below 70 kHz the term is small, above 150 kHz it can exceed the conduction loss at low current.
The body diode is the other term. In a discontinuous flyback the diode conducts before the switch turns on, and its recovery charge appears as a loss in the switch on the next cycle. At 800 V the recovery is fast but the charge is not zero, so a snubber across the diode is worth more than a faster switch.
Where the part fits and where it does not
It fits a 5 to 15 W auxiliary supply on a 230 V or 480 V input, the start up path of a converter, a bias rail in a motor drive, a relay or contactor driver on a high rail, a capacitor bleeder and an active clamp on a low power flyback. It does not fit a 400 V bus at 20 A, a 690 V line, or a converter above 150 kHz at more than two amps.
For a high voltage part the choice is usually made against an existing code with a different body and a different resistance, and the comparison has to include the voltage margin and the recovery of the body diode rather than the current alone. Our power management cross reference page covers how two high voltage candidates are compared on the parameters that decide survival.
The sourcing side of this part is covered on the component lead time solutions. For a high voltage part bought in small lots, that page covers how the lead time is planned rather than discovered.
Questions we get on this code
Is 6 A usable? Not continuously. Twenty nine watts at 6 A has nowhere to go in a TO220. Two to three amps is the working range with a copper island or a small heatsink.
Can it run on a 400 V DC bus? Yes, with margin, and a 600 V part would be cheaper and lower loss. Eight hundred volts is for a 480 V AC input or a flyback with a high reflected voltage.
Does the gate need a negative bias? Not for turn on. A negative off bias helps at high dv/dt where the Miller capacitance can lift the gate, and the plus or minus 30 V window allows it.
What does the order carry? Part number, TO220, and tube packing. We confirm the packing and the date code on the offer.