VBM1803
Product Specifications
VBM1803
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBM1803 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBM1803: 80 V and 195 A in a TO220 with 3 milliohm
The VBM1803 is a single N channel MOSFET in a TO220 body rated at 80 V drain to source, plus or minus 20 V on the gate, a 3 V threshold, 195 A of drain current and 3 milliohm at a 10 V gate. At a 4.5 V gate the same die prints 4 milliohm. The die is listed as trench, which is the structure used below 100 V where the drift region is short and the channel resistance is most of the total.
Eighty volts is an awkward class on paper and a useful one in practice. It sits above the 60 V parts that hold a 48 V rail with a modest margin and below the 100 V parts that cost more per milliohm. It holds a 48 V telecom rail with room for a hot plug transient, a 60 V battery stack at full charge, a 24 V industrial bus during regeneration, and the intermediate rail of a two stage converter that runs at 36 to 48 V.
The headline current is not a working current. At 195 A and 3 milliohm the die makes 114 W. At 100 A it makes 30 W. At 50 A it makes 7.5 W. At 30 A it makes 2.7 W. The TO220 tab removes a fraction of that, so the usable current in this body is set by copper and airflow rather than by the printed number.
Key data for the VBM1803
| Configuration | Single N channel |
| Package | TO220, through hole with the tab on the drain |
| VDS | 80 V |
| VGS | Plus or minus 20 V |
| Vth | 3 V typical |
| ID | 195 A, a die figure at a 25 C case |
| RDS(on) at 10 V | 3 milliohm |
| RDS(on) at 4.5 V | 4 milliohm |
| Technology | Trench |
| Loss at 30 A | 2.7 W at 3 milliohm |
| Loss at 50 A | 7.5 W at 3 milliohm |
| Loss at 100 A | 30 W at 3 milliohm |
Working back from the loss the tab can remove
A TO220 with the tab bolted to an aluminium heatsink and a thermal pad reaches about 1.5 C per watt junction to case plus case to sink, so 7.5 W at 50 A lifts the junction 11 C above the sink and a sink at 90 C leaves the die at 101 C. That is workable. Thirty watts at 100 A is a different proposition: the same path lifts the junction 45 C, and the die approaches its limit while the sink is still cool enough to touch.
On a board with the tab soldered to a copper island rather than bolted to a heatsink, the path is worse and the current falls further. An island of about 600 square millimetres of 70 micrometre copper removes roughly 2 W in still air with the junction at 125 C. That is a working current near 25 A, not 195 A. A two ounce board is roughly half as effective again.
The printed 195 A is reached on a pulse at a fixed case temperature with the die at its limit, which is a legitimate way to publish a bare die but not a way to size a product. Read the resistance and the thermal path, then pick the current that keeps the junction below 110 C at the highest ambient the enclosure allows.
What a 3 V threshold means on a 4.5 V rail
The gate threshold is 3 V typical, and a threshold is where the channel begins to conduct, not where the part is fully on. Driving the gate at 4.5 V puts the gate about 1.5 V above threshold, which is enough to reach the printed 4 milliohm but not enough to keep it there across temperature and process. Driving at 10 V brings the resistance down to 3 milliohm, a 25 per cent reduction in conduction loss for the same current.
At a 4.5 V gate the part still works well in a 12 V or 24 V system where a small charge pump can produce 10 V, and it is the wrong choice for a rail that can only offer 5 V at the gate. A 3.3 V logic output sits at the threshold and the device would run warm and partly on at every pulse, which is the failure mode that looks like a bad solder joint until the gate waveform is examined.
The plus or minus 20 V window is the standard one at this voltage. A 10 V drive leaves 10 V of headroom, which is enough for the ringing of a short gate loop but not for a long one, so the gate resistor and the return path still decide whether the part survives a hard turn off into a shorted load.
Where the part fits and where it does not
It fits the low side of a 48 V synchronous buck at a few tens of amps, a battery disconnect on a 60 V pack, a hot swap pass element on a 48 V backplane, a brushed motor driver at 24 V and a load switch on an industrial 36 V rail. It does not fit a 400 V bus, a 100 kHz converter at high current without a serious gate driver, or a load near the printed current in a TO220 body.
Where a part of this class replaces an existing code, the comparison has to be made on resistance at the actual gate voltage, on the gate charge at the actual drive, and on the thermal path the board offers, because two parts with the same headline current can differ by a factor of two in loss. Our power management cross reference page covers how those three figures are put side by side before a substitution is offered.
The sourcing side of this part is covered on the pin to pin cross reference. For a 80 V part offered as a straight swap, that page covers what has to match beyond the footprint.
Questions we get on this code
Is 195 A available continuously? No. At that current the die makes 114 W, which a TO220 tab cannot remove. Work back from the copper and expect 20 to 40 A continuous depending on the heatsink.
Can the gate be driven from 5 V logic? Only with a driver that produces 10 V. A 5 V output is 2 V above threshold and leaves the part in a resistive state, so the loss rises well above the printed 3 milliohm.
Why does the 4.5 V column matter? It is the column that applies when the drive is weak. It is 4 milliohm against 3, so a calculation that assumed the 10 V figure is 33 per cent optimistic in conduction loss.
What does a purchase order need to carry? Part number, TO220, and the packing the line can take. We confirm the reel or tube quantity on the offer rather than assuming it.