Contact Us

VBM17R20SE

Brand: VBsemi
VBsemi VBM17R20SE is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBM17R20SE — Discrete & Power Semiconductors | Superb Automation

VBM17R20SE

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBM17R20SE from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBM17R20SE: 700 V and 0.165 ohm in the same TO-220 body

The VBM17R20SE is the middle of the 700 V family in this shipment: 700 V drain to source, 0.165 ohm at a 10 V gate, 66 nC of gate charge and 20 A of continuous drain current with the case at 25 C, in the TO-220 body. It shares the body, the gate drive conditions and the diode recovery with the 0.54 ohm sibling and differs only in die area, which is exactly why the pair is useful for a buyer who has to cover two power levels with one approved family.

The place for this part is a 480 V three phase bus at a few hundred watts: the primary switch of a flyback or a forward converter, the power factor stage of a drive, the high side of a motor inverter running at 20 kHz. Above 8 A it is the right choice; below 3 A the 0.54 ohm sibling is cheaper for the same loss.

The sheet is a super junction document with the usual signature rows: 50 V per ns drain source slope, 820 mJ of single pulse avalanche energy, an 80 ns body diode recovery, and a 2400 pF input capacitance that is low enough to keep the drive simple at any frequency under 100 kHz.

The parameter table

Drain to source voltage700 V
Gate to source voltageplus or minus 30 V
On resistance at 10 V gate, 6.5 A, 25 C0.165 ohm typical
Gate threshold at 250 microamp2.5 V minimum, 4.5 V maximum
Continuous drain current, case at 25 C and 100 C20 A and 12 A
Pulsed drain current60 A
Single pulse avalanche energy, 28.2 mH, 10 A start820 mJ
Power dissipation, case at 25 C180 W
Junction to case and junction to ambient0.7 and 62 C per watt
Linear derating factor1.67 W per C
Operating junction and storage rangeminus 55 to plus 150 C
Breakdown voltage temperature coefficientminus 0.70 V per C
Zero gate voltage drain current at 700 V1 microamp maximum
Zero gate voltage drain current at 560 V, 125 C100 microamp maximum
Input, output and reverse transfer capacitance2400, 80 and 4 pF
Effective output capacitance, energy and time related62 and 213 pF
Total gate charge at 520 V, 8 A66 nC
Gate source and gate drain charge15 and 19 nC
Turn on delay and rise time18 and 24 ns typical
Turn off delay and fall time80 and 12 ns typical
Gate input resistance0.8 ohm typical
Body diode forward drop at 8 A1.5 V maximum
Body diode recovery time and charge80 ns and 5.8 microcoulomb
Drain source voltage slope at 125 C50 V per ns

Loss at the working current, not at the rated current

At 10 A through 0.165 ohm the die dissipates 16.5 W, which with 0.7 C per watt is a 12 C rise to the case. A heatsink of 3 C per watt holds the junction near 100 C at a 50 C ambient, which is a comfortable margin. At the rated 20 A the dissipation is 66 W and the rise to the case alone is 46 C, so the case must be held near 100 C to stay inside the junction limit. Both numbers are useful, and they describe two different products.

In still air the part sees 62 C per watt, which supports 2.02 W at 25 C and 1.61 W at 50 C, equal to 3.50 A and 3.13 A. That is the figure a standby or a bias supply has to live with, and it is the reason the part is quoted with a heatsink in every application above 3 A.

The 180 W dissipation row sits within a watt of the 178.6 W the thermal pair supports at a 150 C junction, so this sheet is internally consistent on the thermal side. That consistency is worth noting because it is not universal in the band, and a buyer who sees a dissipation row 30 per cent above the thermal pair should ask which one is the limit.

The high voltage leakage row that matters at 125 C

One row on this sheet deserves more attention than it usually gets: 100 microamp of drain current at 560 V with the junction at 125 C. That is leakage, not conduction, and at 560 V it is 56 mW of loss with the gate firmly off. In a bridge with four devices it is 224 mW of standing loss in an enclosure that is already warm, and in a high side clamp it is the current that charges the bootstrap path when nobody is switching.

At 25 C the same row is 1 microamp, a factor of one hundred lower, so a qualification that measures leakage cold will pass a wafer that leaks ten times the typical figure hot. The 125 C row is the one to test, and it is the reason our incoming plan for high voltage switches specifies a hot leakage measurement rather than a room temperature one.

The breakdown temperature coefficient of minus 0.70 V per C is the other high voltage row. At 125 C the 700 V part behaves like 612 V, which is still above a 680 V bus only because the bus is not present at that temperature. A board that runs near the rated voltage and near the rated junction is running on two margins that shrink together.

Where this part and its sibling split the work

The 0.54 ohm part carries 2 W in still air at 1.9 A and the 0.165 ohm part carries the same 2 W at 3.5 A, so the split between them is roughly 2 A of still air current or a heatsink. On a heatsink the two parts cover 3 A to 8 A and 8 A to 20 A respectively, and one approved family covers a whole product line without a second qualification.

Against a 650 V part at 0.085 ohm, this one gives up 50 V of margin and gains 0.08 ohm, which is 8 W at 10 A. On a 680 V bus the 650 V part cannot be used at all, and on a 400 V bus the 650 V part is the better economic choice. The bus decides, not the data sheet. Our component cost work starts from that split, because buying the 700 V part for a 400 V bus is the most common way to overpay in this class.

When several power levels ship on one board family, the kitting service keeps the two die sizes separated by part number and by reel, so a line cannot mix them, and the incoming inspection plan measures on resistance and hot leakage on both.

The 60 A pulsed row assumes a 300 microsecond pulse with a cool junction, so it describes a fault rather than an operating point. In a motor drive the part sees a three to five times overload for as long as the protection takes to act, and that is a question for the safe operating area curve rather than for the pulsed row. A 20 A part asked for 40 A for 10 ms is being asked to shed 32 W from a die that removes 2 W in still air, and the protection has to act well before the thermal time constant of the tab runs out.

Questions before a reel is booked

First, the bus and the surge. 700 V against a 680 V bus is 3 per cent, so the clamp and the leakage inductance have to be known before the part is frozen. Ask for the measured peak, not the calculated one.

Second, the gate. 66 nC at 10 V is 0.066 W at 100 kHz, which is easy, but the 19 nC gate drain charge at 520 V sets a 50 V per ns edge. The gate resistor and the snubber are part of the approval.

Third, the hot leakage and the diode. Both are temperature dependent and both are invisible in a 25 C test. A first article that measures only on resistance has measured the easiest row on the sheet.