VBM17R08SE
Product Specifications
VBM17R08SE
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBM17R08SE from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBM17R08SE: 700 V at 0.54 ohm for the low current end of a bus
The VBM17R08SE is a 700 V N channel super junction MOSFET in the TO-220 body, with 0.540 ohm at a 10 V gate, 82 nC of gate charge and 8 A of continuous drain current with the case at 25 C. It is the low current end of the 700 V family in this shipment, and its job is the place where the voltage is high and the current is small: a standby supply, a bias rail, a relay driver, an auxiliary winding on a motor drive.
The 700 V rating exists for buses that run above the usual 400 V. A three phase 480 V rectified bus sits near 680 V, and a 650 V part has no margin left on it. That is the only reason to pay 0.54 ohm where a 650 V part would give 0.085 ohm at the same current. If the bus is 400 V, this is the wrong part and the wrong column of the catalogue.
The rest of the sheet is conventional super junction: 50 V per ns drain source slope, 870 mJ of single pulse avalanche energy, a 15 V to 19 nC gate drain charge and a 990 pF input capacitance, which is low enough for a small driver to run the part at high frequency where the current is small.
The ratings in one table
| Drain to source voltage | 700 V |
| Gate to source voltage | plus or minus 30 V |
| On resistance at 10 V gate, 2.5 A, 25 C | 0.540 ohm typical |
| Gate threshold at 250 microamp | 2.5 V minimum, 4.5 V maximum |
| Continuous drain current, case at 25 C and 100 C | 8 A and 5 A |
| Pulsed drain current | 24 A |
| Single pulse avalanche energy, 28.2 mH, 4 A start | 870 mJ |
| Power dissipation, case at 25 C | 160 W |
| Junction to case and junction to ambient | 0.7 and 62 C per watt |
| Linear derating factor | 1.67 W per C |
| Operating junction and storage range | minus 55 to plus 150 C |
| Breakdown voltage temperature coefficient | minus 0.70 V per C |
| Input, output and reverse transfer capacitance | 990, 80 and 4 pF |
| Effective output capacitance, energy and time related | 62 and 213 pF |
| Total gate charge at 520 V, 8 A | 82 nC |
| Gate source and gate drain charge | 15 and 19 nC |
| Turn on delay and rise time | 18 and 24 ns typical |
| Turn off delay and fall time | 80 and 12 ns typical |
| Gate input resistance | 0.8 ohm typical |
| Body diode forward drop at 8 A | 1.5 V maximum |
| Body diode recovery time and charge | 80 ns and 5.8 microcoulomb |
| Body diode peak reverse recovery current | 35 A |
| Drain source voltage slope at 125 C | 50 V per ns |
| Soldering peak temperature for 10 s | 260 C |
The current this part really carries on a board
At 8 A through 0.540 ohm the die dissipates 34.6 W, which with 0.7 C per watt means a 24 C rise to the case and a very ordinary heatsink. The rating is not the constraint here; the on resistance is. That is the opposite of the high current parts in the same body, where the thermal path limits first, and it is a useful reminder that the 8 A row is not a thermal statement.
In still air the part sees 62 C per watt, which supports 2.02 W at 25 C and 1.61 W at 50 C, equal to 1.93 A and 1.73 A. A standby supply drawing 1 A through this part dissipates 0.54 W and needs nothing more than copper. The same part at 4 A in still air dissipates 8.6 W and will run at a junction far above the ambient, which is where most of the field failures in this kind of circuit begin.
The printed 160 W dissipation is below the 178.6 W that the thermal pair supports at a 150 C junction, so this sheet is conservative on that row, unlike two of its siblings. Where the printed dissipation sits below the thermal pair, the lower figure is the one to use, and here it happens to be the honest one.
Why 82 nC of gate charge on a 990 pF part
82 nC of total gate charge against 990 pF of input capacitance looks inconsistent at first glance, and it is not: the charge is dominated by the gate drain region at 520 V of drain bias, where the charge balanced column holds charge that does not appear in the small signal capacitance at low drain voltage. The practical reading is that the drive energy is set by the 520 V figure, not by the 990 pF, so a 10 V driver at 100 kHz spends 0.082 W on the gate regardless of how small the capacitance looks.
The 19 nC gate drain charge is the term that decides the turn on loss and the dv/dt. At 50 V per ns the part crosses a 600 V bus in 12 ns, which is fast enough to need a gate resistor and a snubber decision rather than a hope. The 80 ns turn off delay with a 12 ns fall is the shape printed with a 9.1 ohm gate resistor, and that resistor is a sensible first value on a new board.
Where 700 V is the requirement rather than the preference
A 480 V three phase supply rectifies to about 680 V, and a 700 V device leaves 3 per cent margin, which is thin but is what the class offers. In that application the alternative is an 800 V part at 0.38 ohm or a 900 V part at over 1 ohm, so 700 V at 0.54 ohm is the middle of the ladder and usually the cheapest loss per watt. In a 400 V single phase supply the same part wastes 0.45 ohm against a 650 V sibling and should not be used.
The 870 mJ avalanche rating covers the flyback leakage spike in a small auxiliary supply, which is where this part most often appears. A 4 A start into 28.2 mH is a real inductive event, and the 1.67 W per C derating is still the limit that decides whether a clamp is needed on a repetitive surge.
Where a customer is moving from an older planar 700 V part at 1 ohm or more, the gain is roughly half the conduction loss at the same current, and the price is a faster edge that may need a gate resistor change. Our strategic sourcing work treats that resistor as part of the part change, and the obsolete part cross reference is where most of these 700 V changes start, because the planar parts are the ones leaving the market.
Two rows on this sheet belong in the qualification file rather than in the sales summary. The first is 10 microamp of drain current at 520 V with the junction at 125 C, which at 680 V of bus is close to the working voltage and ten times the cold figure. The second is the minus 0.70 V per C breakdown coefficient, which turns 700 V into 612 V at a 125 C junction. A board that assumes the voltage margin and the thermal margin at the same time is assuming two things that shrink together.
Questions before a reel is booked
First, the bus voltage. If it is 400 V this part should not be quoted, and if it is 680 V the next question is the surge, because 700 V leaves little room. Measure the peak on the first article rather than reading the nominal.
Second, the driver. 82 nC at 10 V is easy for any controller, but the 19 nC gate drain charge at 520 V sets the dv/dt, and a fast edge on a 680 V bus is an EMI problem before it is a loss problem.
Third, the second source. The 700 V class has fewer suppliers than 650 V, and the parts that do exist differ in gate charge by a factor of two. We hold the gate charge and the diode recovery with the supplier scorecard so a substitute is compared on the rows that change the circuit, not only on voltage and resistance.