Contact Us

VBM16R20SE

Brand: VBsemi
VBsemi VBM16R20SE is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBM16R20SE — Discrete & Power Semiconductors | Superb Automation

VBM16R20SE

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBM16R20SE from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBM16R20SE: 600 V and 20 A at 150 milliohm in TO220

The VBM16R20SE is a single N channel MOSFET in a TO220 body rated at 600 V drain to source, plus or minus 30 V on the gate, a 3.5 V threshold, 20 A of drain current and 150 milliohm at a 10 V gate. The die is listed as SJ deep trench.

This is the 600 V member of a family that also carries a 650 V part at the same resistance in this band. That pair is worth understanding before an order is placed: same 150 milliohm, same 20 A label, 50 V more margin on the other code. Where the price and the package are the same, the higher voltage part is the better buy, and where the 600 V part is cheaper it is the right one for a 325 V bus.

One hundred and fifty milliohm at 20 A is 60 W. At 10 A it is 15 W. At 5 A it is 3.75 W. The working current on a clip on heatsink is 8 to 12 A.

Key data for the VBM16R20SE

ConfigurationSingle N channel
PackageTO220 through hole with a metal tab
VDS600 V
VGSPlus or minus 30 V
Vth3.5 V
ID20 A, a die figure at a 25 C case
RDS(on) at 10 V150 milliohm
TechnologySJ deep trench
Loss at 5 A3.75 W at 150 milliohm
Loss at 10 A15 W at 150 milliohm
Loss at 20 A60 W at 150 milliohm
Gate chargeNot printed, ask for the curve at the working drain voltage

Six hundred volts against six hundred and fifty

On a 325 V bus both parts have plenty of margin. The 600 V part has 275 V and the 650 V part 325 V, and in a bridge leg with a short loop the spike is 50 to 100 V, so both are comfortable. The difference appears in a flyback, where the reflected voltage and the leakage spike are added to the bus.

On a 400 V bus the 600 V part has 200 V of margin, which covers a 100 V reflected voltage and a 100 V spike exactly, with nothing left. The 650 V part has 250 V and a little room. That is the case where the higher voltage member of the pair earns its price.

An engineer choosing between the two should look at the whole production, not at one board. A part that is marginal in one product line tends to become a field return in another, and a 50 V step is cheap insurance against a second build.

Deep trench behaviour in a hard switched bridge.

A deep trench die at 600 V has a low resistance for its area and a body diode with a sharp recovery. In a hard switched bridge the recovery of that diode appears as a loss in the opposite device, and at 10 A and 30 kHz it is worth a few watts, which on a 15 W conduction loss is significant.

The usual answer is a short dead time with a fast gate, so the diode conducts for less time before the opposite device turns on. That reduces the recovery loss and increases the risk of a shoot through, and the balance is set by the driver and by the threshold spread of the parts.

Where the topology is a boost or a flyback, the diode recovery is not an issue in the same way, and the part is easier to use. The frequency can go higher until the output capacitance loss becomes the limit, which at 325 V and 30 kHz is a couple of watts.

Heatsink and isolation at 325 V

At 10 A the loss is 15 W and a clip on heatsink with a silicone pad holds it. At 15 A it is 34 W and the heatsink has to be larger. The tab is the drain at the bus voltage, so the insulator is a safety part and its thickness is part of the thermal budget.

A TO220 junction to case resistance of about one degree per watt means 15 W puts the case 15 degrees above the heatsink before the pad. With a 60 C heatsink the junction sits near 80 C, which leaves margin on a 150 C device. At 34 W the same arithmetic gives 95 C on a 60 C heatsink, which is still inside but with less room for a hot day.

The source leads carry the current and their inductance is part of the loop. A wide pour on both sides of the board with the leads through it lowers both the resistance and the inductance, and at 10 A the difference shows up in the drain spike as much as in the loss.

Where the part fits and where it does not

It fits a 230 V front end power factor stage at 5 to 10 A, a boost converter on a 325 V bus, an inverter leg in a small drive, an active clamp and a flyback at 30 to 60 kHz. It does not fit a 400 V bus in a flyback without a clamp, a 20 A continuous load, or a resonant converter above 100 kHz.

For a 600 V part the questions are the sum of bus, reflected voltage and spike, the diode recovery at the frequency and the heat the enclosure allows. Our supplier onboarding checklist page covers what has to be documented before a new source ships the first reel.

The sourcing side of this part is covered on the supplier corrective action. For a part that carries a whole product line, that page covers how a failure is closed out at the source.

Questions we get on this code

Is it the same die as the 650 V part? The resistance and the current label match, so they are close relatives. The 650 V part carries 50 V more margin for what is usually a small price difference.

Is 20 A available continuously? At 60 W, no. On a clip on heatsink 8 to 12 A is the working range.

Does the tab need an insulator? Yes. The tab is the drain at 325 V, so a shared heatsink needs an insulator and a shoulder washer.

What should a purchase order carry? Part number, TO220, and the packing the line can take. We confirm the tube quantity on the offer.