Contact Us

Supplier Corrective Action

Supplier Corrective Action

The same defect arrives on the third shipment in a row, and the corrective action report says the operator was retrained. Nothing in the report explains how a part that was already wrong left the supplier's building, and nothing in it will stop the fourth shipment. That is the normal state of supplier corrective action in electronics, and it is fixable with a shorter, stricter template.

A corrective action is not an apology with a form attached. It is a claim that a cause has been found and removed, with evidence that the same failure cannot reach you again through the same route.

Why the same defect comes back

Four failure modes account for most repeats. The cause is named at the point of detection rather than the point of escape, so the fix is applied where the part was checked and not where it went wrong. The action is a people action, retraining or added attention, which leaves the process that produced the defect untouched. The verification is a batch of five pieces checked by the person who wrote the report. And the report is closed when the paperwork is filed rather than when the next three lots have run clean.

What a corrective action has to contain

The eight discipline structure is standard, but the substance sits in what each step is required to prove.

StepWhat it must containCommon substitute that should be rejected
Problem descriptionPart number, lot, quantity affected, defect rate, how it was detectedA sentence with no lot traceability
ContainmentWhat was stopped, sorted, or quarantined, and the date it was completeA promise to screen future lots
Escape pointWhere the defect passed the last check before shipment, and why that check missed itSilence, or a statement that checks are adequate
Root causeThe process condition that produced it, verified by a test that shows the causeOperator error, without the condition that allowed it
Corrective actionChange to process, tooling, specification or inspection, with the document revisedRetraining only
VerificationData from three consecutive lots, or a stated sample, against the defect rate beforeFive pieces checked once
Systemic read acrossWhich other part numbers or lines carry the same conditionNone
ClosureDate, owner, and the next review point if the rate moves againClosed by the requester alone

The escape point row is the one most often left blank, and it is the one that decides whether the action holds. A defect that was produced and detected is a process problem. A defect that was produced, missed and shipped is a control problem, and fixing only the first leaves the second in place.

Containment is a stopgap, not an answer

Sorting incoming material feels like progress because it stops the line from stopping. It also moves the cost to the receiving dock and leaves the producing process unchanged, which is why a supplier can contain the same defect for a year without ever correcting it.

Containment should carry an end date and a stated quantity, and it should be tied to the verification data that will retire it. If a supplier proposes containment with no exit, the action has not started.

Verification of effectiveness

The question is not whether the change was made but whether the defect rate moved, measured on lots produced after the change. Three consecutive lots at the previous defect rate or better is a reasonable bar for a mechanical or assembly defect. For a defect that appeared once in ten thousand pieces, the bar has to be a process check rather than an outcome count, because no sample will prove the absence of a rare event.

Where the cause is a purchased sub component, verification has to reach the sub tier, otherwise the same failure returns through a different supplier name.

How SUPERB PCBA closes a nonconformance

Incoming material is counted by X-ray against the reel or tray and compared to the purchase order, and part number, quantity, date code and maker markings are checked in the same pass. Material that fails is quarantined with the lot and the count recorded, so a containment statement can be written with quantities rather than adjectives.

On the assembly side, defects are caught at defined stations rather than at final inspection: 3D SPI after print, 3D AOI after reflow, X-ray to IPC-7095 with voiding under five percent on BGA and bottom terminated parts, and a seventeen step flow with ten QC stations under IPC-A-610 Class 2 and Class 3. The system is ISO 9001, with ISO 13485 for medical builds, and components carry a 730 day warranty from receipt.

When a nonconformance is raised against supplied material, the response is written against the same eight rows, and a pin to pin substitute is never used as a corrective action without written customer approval. The records that support the closure are the same records an auditor will ask for: lot, quantity, date code, storage class, bake record where moisture sensitive parts are involved, and the inspection result at receipt.

Measuring whether the action worked

MeasureWhat it showsWindow
Defect rate by lot after the changeWhether the condition was actually removedThree consecutive lots
Repeat count on the same part and defect codeWhether the escape route is still openRolling six months
Containment hours per lotThe real cost of a stopgap that never endsPer receipt
Open actions past dueWhether the supplier treats the report as paperworkMonthly
Same condition found at other part numbersWhether the read across was doneAt closure

These measures belong on the same supplier review as delivery and price. A supplier with a clean delivery record and a permanent containment line is not a good supplier, it is a supplier whose sorting cost has not been billed back yet.

Supplier corrective action questions

Should a corrective action be raised for every defect?

No. A single isolated defect with a clear cause and no repeat is handled by a deviation or a replacement. The report is for a condition that can recur, or for a defect that escaped a control that was supposed to catch it.

Who should verify effectiveness?

Whoever receives the material, using lot data rather than the supplier's summary. Self verification by the author of the report is the most common reason an action closes and the defect returns. The receiving side of this is set out under incoming inspection plan.

What belongs in the supplier score if actions keep repeating?

The repeat count, not the number of reports filed. A supplier that files ten reports and repeats twice is worse than one that files two and repeats none. How that lands in a review is covered under supplier scorecard.

Next step

Send the nonconformance you are currently holding, with the lot, the defect rate and whatever the supplier has replied so far. The reply returns the rows that are missing from the response, the escape point that has not been addressed, and the verification data that would be needed to close it. For the audit that usually follows, see supplier quality audit.