VBM16R04
Product Specifications
VBM16R04
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBM16R04 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBM16R04: 600 V and 4 A at 1300 milliohm
The VBM16R04 is a single N channel MOSFET in a TO220 body rated at 600 V drain to source, plus or minus 30 V on the gate, a 3.5 V threshold, 4 A of drain current, 1040 milliohm at a 4.5 V gate and 1300 milliohm at a 10 V gate. The die is planar.
The two resistance columns are printed in the wrong order for a MOSFET. A higher gate voltage should lower the resistance, and here the 10 V figure is the higher of the two. The vendor page repeats the same pair in its own parameter list, so the inversion is in the source data rather than in this page, and it is flagged here rather than smoothed over.
Whichever column is right, the part is a small high voltage switch. At 1300 milliohm and 4 A the loss is 20.8 W. At 1 A it is 1.3 W. At 0.5 A it is 0.33 W. The working current is under an amp, and the class is chosen for voltage.
Key data for the VBM16R04
| Configuration | Single N channel |
| Package | TO220 through hole with a metal tab |
| VDS | 600 V |
| VGS | Plus or minus 30 V |
| Vth | 3.5 V |
| ID | 4 A, a die figure at a 25 C case |
| RDS(on) at 4.5 V | 1040 milliohm as printed |
| RDS(on) at 10 V | 1300 milliohm as printed, higher than the 4.5 V column |
| Technology | Planar |
| Loss at 0.5 A | 0.33 W at 1300 milliohm |
| Loss at 1 A | 1.3 W at 1300 milliohm |
| Loss at 4 A | 20.8 W at 1300 milliohm |
When two columns disagree, measure
A parameter table that shows a lower resistance at a lower gate voltage is a table with a problem. It can be two dies sharing one part number, a column that was filled from a different revision, or a transcription error at the source. The number to use is the one measured on the part in hand.
For a product that only needs a few hundred milliamps at 600 V, the difference between 1040 and 1300 milliohm is 0.1 W, which does not change the answer. At 2 A it is 1 W, which does. Where the current is that high the part is probably the wrong choice anyway, because at 2 A and 1300 milliohm the loss is 5.2 W in a small die.
The sensible route is a sample measurement on a curve tracer at 10 V and at 4.5 V, at the working current, on a warm part. That takes ten minutes and settles a question the catalogue page cannot.
Planar dies at six hundred volts.
A planar die at 600 V is the older of the two structures used in this band, and it is still made because it is rugged and cheap. Its resistance per unit area is higher than a charge balance die, and its capacitance is lower than a deep trench part of the same voltage, which is an advantage in a low current switching node.
Where the part is used as a start up element, a bias supply switch or a discharge path, the low capacitance matters more than the resistance. A smaller capacitance means less energy lost at every turn on and a smaller displacement current into the gate, which makes the drive simpler.
Ruggedness is the other reason. A planar die has a wider safe operating area than a deeply compensated one at the same current, so it survives a short circuit for longer. In a circuit where a fault is possible and the protection is slow, that tolerance is worth more than a lower resistance.
Small die, large package
A TO220 with a die this small runs cool at the currents it is used at. At 0.5 A the loss is 0.33 W and the tab removes it in still air without a heatsink, which is one of the reasons this body is chosen for a high voltage housekeeping function: the thermal problem disappears.
The tab still sits at the bus voltage, so the package brings a safety consideration the die does not. An insulator and a shoulder washer are needed if the heatsink is earthed, and the creepage from the tab to the mounting hole is part of the board.
The gate at 10 V with a 30 V window is easy to drive, and the 3.5 V threshold keeps the part off with a resistor to source. At 600 V the leakage from drain to gate is small but not zero, so a floating gate is still a bad idea.
Where the part fits and where it does not
It fits a 400 V start up circuit, a bias supply at a few hundred milliamps, a discharge path, a clamp and an auxiliary switch in a high voltage product. It does not fit a main power path at amps, a 1000 V string, or a position where the loss has to be under a watt at 2 A.
For a small part at high voltage the questions are the measured resistance at the drive voltage, the creepage and whether a second source exists. Our sourcing audit trail page covers what is recorded when a part is qualified and how the record is kept for a later build.
The sourcing side of this part is covered on the supplier quality audit. For a part whose published table disagrees with itself, that page covers what is verified at the source.
Questions we get on this code
Why is the 10 V column worse than the 4.5 V one? The source data prints them that way and the vendor page repeats it. Treat it as an open question and measure a sample at the working current.
Can it carry 4 A? At 20.8 W in a small die, no for any length of time. Under an amp it is comfortable.
Does it need a heatsink? Not at the currents it is used at. The tab alone removes the loss.
What should a purchase order carry? Part number, TO220, and the packing the line can take. We confirm the tube quantity on the offer.