Contact Us

VBM165R22

Brand: VBsemi
VBsemi VBM165R22 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBM165R22 — Discrete & Power Semiconductors | Superb Automation

VBM165R22

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBM165R22 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBM165R22: 650 V and 0.28 ohm in a three lead TO-220AB

The VBM165R22 is an N channel trench MOSFET rated 650 V drain to source with a plus or minus 30 V gate, supplied in the TO-220AB body and tested for gate resistance and avalanche energy at the end of the line. The product summary states 0.280 ohm at a 10 V gate, a maximum gate charge of 98 nC and 22 A of continuous drain current with the case held at 25 C.

The part sits in the older trench family rather than in the super junction family that now covers most of the 600 V to 700 V range. That shapes every comparison a buyer makes. A super junction device of the same voltage class usually prints a quarter of this on resistance, while this part answers with a 67 A pulsed rating, 139 mJ of single pulse avalanche energy and a 384 ns body diode recovery. Whether that trade is right depends on the circuit and not on the order of the rows on page one.

Three rows describe the part better than the summary does: 40 C per watt from junction to ambient on a one inch square board, 0.4 C per watt from junction to case, and 312 W of dissipation with the case at 25 C. Nothing else on the sheet changes an engineering decision as much as the gap between those three numbers.

The parameter table in full

Drain to source voltage650 V
Gate to source voltage, DC and AC above 1 Hzplus or minus 30 V
On resistance at 10 V gate, 11 A, 25 C0.280 ohm maximum
Gate threshold at 250 microamp3 V minimum, 5 V maximum
Continuous drain current, case at 25 C and 100 C22 A and 14 A
Pulsed drain current, repetitive67 A
Single pulse avalanche energy, 2.3 mH, 11 A start139 mJ
Power dissipation, case at 25 C312 W
Junction to case and junction to ambient0.4 and 40 C per watt
Linear derating factor2.5 W per C
Operating junction and storage rangeminus 55 to plus 150 C
Drain source voltage temperature coefficientminus 0.6 V per C
Input, output and reverse transfer capacitance1938, 169 and 18 pF
Total gate charge, typical and maximum49 and 98 nC
Gate source and gate drain charge13 and 22 nC
Turn on delay and rise time21 and 42 ns typical
Turn off delay and fall time47 and 40 ns typical
Gate input resistance1.4 ohm typical
Body diode forward drop at 11 A1.2 V maximum
Body diode recovery time and charge384 ns and 4.7 microcoulomb
Body diode peak reverse recovery current23 A
Drain source voltage slope at 125 C24 V per ns
Soldering peak temperature for 10 s300 C

Two thermal rows that decide the real current

312 W at a 25 C case describes the package and the die attach, not the board. The same page prints 40 C per watt from junction to ambient, so on a one inch square board in still air the allowed rise of 125 C supports 3.12 W. That is one hundredth of the headline. Working back through 0.280 ohm, 3.12 W carries 3.34 A at a 25 C ambient and 2.50 W carries 2.99 A at 50 C.

Run the same arithmetic at the 22 A continuous rating and the die has to shed 135 W, which needs the case held below 55 C to keep the junction under 150 C. A board that starts from the 22 A row and then asks for a small heatsink started from the wrong row. The first useful question is the case temperature at full load, and the rest of the thermal file follows from it.

The linear derating factor of 2.5 W per C is the third anchor. It is simply 312 W divided by the 125 C allowed rise, so any dissipation above 3.12 W in still air has to be removed by copper, airflow or a heatsink. When a customer sends a board with a 4.7 W load on this part and no heatsink, the answer is a different case or a different part, not a different solder profile.

What the switching table says about a hard commutated bridge

Gate charge is printed twice, 49 nC typical and 98 nC maximum, and the maximum is the number to use when a driver is sized because the spread across the process is a factor of two. At 10 V of drive and 60 kHz, 98 nC costs 0.059 W of drive power, which is small against the 3.12 W the board can remove, so the gate is not the limit. The internal gate resistance of 1.4 ohm is also low enough that a 4.7 ohm external resistor dominates the turn off shape.

The body diode is the row that changes behaviour. 384 ns of recovery, 4.7 microcoulomb of charge and 23 A of peak reverse current describe a slow diode, and in a half bridge with hard commutation that current appears as a spike the other switch has to absorb. A super junction device at 60 ns would not. Allow dead time, add a parallel Schottky, or keep the part in a topology where the diode never conducts reverse current at full bus.

The 24 V per ns drain source slope is half the 50 V per ns printed on the super junction sheets in the same body, which is consistent with the slower diode. A gate resistor chosen for EMI on the fast parts will be too small here, and one chosen here will be too slow on the fast parts. Treat the resistor as part of the part number, not as a board detail to be decided later.

Where this part still earns its place

Values in the 650 V class exist for a 400 V bus with margin. 650 V against 400 V leaves 62 per cent, which covers the overshoot that a 20 nH switching loop produces at 20 A. The application list covers consumer displays, server and telecom supplies, welding, induction heating, motor drives and battery chargers, and the common thread is a switch running at tens of kHz that tolerates a slow diode. A 3.5 kW PFC stage at 65 kHz, an induction cooker half bridge, or a 400 V pump drive all fit. A 100 kHz LLC with a small resonant tank does not, because the recovery and the 0.28 ohm both cost more than the part saves.

A buyer comparing this part with the super junction sibling in the same body (VBM165R32S at 0.085 ohm) should compare the thermal paths rather than the current rows. The sibling removes conduction loss by a factor of three and recovery by 324 ns, and it brings a 62 C per watt ambient path instead of 40. On a heatsink the sibling wins. On a board with no airflow and a 1 A load, the difference in ambient resistance matters more than the difference in on resistance.

Where a customer is replacing an older 600 V trench part, the 650 V rating is the useful part of the change: it keeps the same drive and the same footprint and adds 50 V of headroom for the surge that a 400 V bus sees when a motor decelerates. Our power management cross reference work starts from the diode recovery and the gate charge net, because those two decide whether the replacement behaves on the same board.

Questions we answer before a reel is booked

First, the gate drive. A threshold of 3 V to 5 V means this is not a logic level device, and a 5 V driver runs it in the linear region, worse at low temperature where the threshold climbs. Use 10 V, then check the external gate resistor against the 1.4 ohm internal value so the waveforms match page two.

Second, the avalanche figure. 139 mJ is quoted from a 2.3 mH load with an 11 A start and a 25 C junction, which is one event. A supply that sees a surge on every cycle belongs on the repetitive curve and on the derating factor, not on that row.

Third, the second source. Trench 650 V parts at 0.28 ohm are available from several suppliers in the same TO-220AB body with different gate charge and different diode recovery, so the comparison has to include the diode, the threshold and the thermal pair. We hold those three on file for every alternate we approve, and we check the incoming lot against them rather than against the summary page. The lead time work and the incoming inspection plan both use that file, so a reel that measures outside the window is caught before it reaches the line.