VBM165R15SE
Product Specifications
VBM165R15SE
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBM165R15SE from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBM165R15SE: a 650 V super junction switch at 0.22 ohm
The VBM165R15SE is a 650 V super junction N channel MOSFET in the TO-220 body, printed at 0.220 ohm with a 10 V gate and 5 A, 15 A of continuous drain current with the case at 25 C, 190 W of dissipation and a 820 mJ single pulse avalanche rating. The device comparison on the first page names server and telecom supplies, switch mode supplies, power factor correction and discharge lighting.
Super junction parts are chosen for on resistance per unit area, and this one delivers 0.22 ohm from a die that a planar part would need twice the area to reach. The cost of that structure is a strongly voltage dependent output capacitance and a body diode that recovers slowly for its size, and those two facts decide where the part can be used without trouble.
The ratings a buyer checks first
| Drain to source voltage | 650 V |
| Gate to source voltage | plus or minus 30 V |
| On resistance at 10 V gate, 5 A | 0.220 ohm typical |
| Continuous drain current, case at 25 C and 100 C | 15 A and 9 A |
| Pulsed drain current | 45 A |
| Single pulse avalanche energy from 28.2 mH | 820 mJ at 7 A |
| Dissipation with the case at 25 C | 190 W |
| Linear derating factor | 1.67 W per C |
| Junction to case and junction to ambient | 0.7 and 62 C per watt |
| Gate threshold at 250 microamp | 2.5 V minimum, 4.5 V maximum |
| Input capacitance at 100 V | 1800 pF typical |
| Output capacitance and reverse transfer capacitance | 80 and 4 pF |
| Effective output capacitance, energy related | 62 pF typical |
| Effective output capacitance, time related | 213 pF typical |
| Total gate charge at 520 V, 8 A | 69 nC typical |
| Gate source and gate drain charge | 15 and 19 nC |
| Turn on delay and rise time | 18 and 24 ns typical, 25 and 55 ns maximum |
| Turn off delay and fall time | 80 and 12 ns typical |
| Gate input resistance | 0.8 ohm typical |
| Body diode forward drop at 8 A | 1.5 V maximum |
| Body diode recovery time and charge | 80 ns and 5.8 microcoulomb |
| Peak diode recovery current | 35 A |
Reading the electrical table instead of the front page
The two effective capacitance figures are the heart of this sheet. The energy related value is 62 pF and the time related value is 213 pF, a ratio of more than three to one. That spread is the signature of a super junction structure whose capacitance collapses as the drain voltage rises. For a hard switched turn on at 380 V the loss is roughly half of 213 pF times the square of 380 V, about 15 microjoule per cycle, which is 1.5 W at 100 kHz. The same calculation done with the 62 pF energy figure would give about 0.45 W and would be wrong for a converter that charges the capacitance from zero on every cycle.
The on resistance and the current rows are consistent with each other. Fifteen amps at 0.22 ohm is 49.5 W, well inside the 190 W allowed at a 25 C case, and at a 100 C case the current row drops to 9 A, which is 17.8 W at the same resistance. In free air the 62 C per watt figure caps the part at about 2.4 W, so a bare board carries roughly 3.3 A. Those three numbers describe a part that needs a heatsink for anything above a few amps, which is normal for the class but is not what the 15 A headline suggests.
The body diode is the compromise. A recovery time of 80 ns looks fast, but the recovered charge is 5.8 microcoulomb and the peak recovery current is 35 A, which is more than twice the continuous rating. In a hard switched bridge those numbers turn into a large current spike on the opposite switch and a corresponding loss. In a discontinuous stage or a resonant converter the diode never sees a forced recovery, and the same figures are irrelevant. The 35 A peak recovery current is the number that matters in a bridge, because it flows through the opposite switch while that switch is turning on.
Where a 650 V super junction part earns its place
Continuous mode power factor correction is the classic use, where the low on resistance keeps conduction loss down at 3 A to 6 A and the switch is turned on into a diode that is already conducting, so the output capacitance loss is recovered into the load rather than dissipated. It is also a good choice for the primary of an LLC or a phase shifted bridge, where the resonant transition removes the capacitance loss entirely and the low gate charge keeps the drive simple. The 69 nC total charge with 19 nC on the gate drain node is what makes the resonant primary attractive, since a small driver switches the part at 200 kHz without needing its own heatsink.
The second home is a server or telecom rectifier running at 100 kHz to 200 kHz, where the 0.22 ohm die keeps the conduction loss under 10 W at 6 A and the 190 W dissipation rating leaves room for the transient. Where a circuit hard switches at 400 V and does not recover the capacitance energy, the 1.5 W per 100 kHz figure is the whole argument for moving to a resonant topology rather than to a bigger die.
Sourcing notes and the second source question
Super junction parts are the area where a catalogue cross reference fails most often, because two devices can match on voltage, on resistance and on gate charge and differ by a factor of three in time related output capacitance. The comparison has to be made on the capacitance that the topology actually charges. The component lead time solutions page describes how such a substitution is qualified on a live bill of materials, and the check we insist on is a switching loss measurement on the customer board, not a comparison of data sheet rows.
The second risk is the gate. An internal gate resistance of 0.8 ohm with 19 nC of gate drain charge gives a fast device that will ring with a long gate track. A substitute with 3 ohm of internal resistance will be quieter and slower, which changes the switching loss and can change the EMI result. The pin to pin cross reference page carries the gate resistance and the internal gate charge figures beside the resistance for that reason. A part with 4 ohm of internal resistance in the same footprint passes an electrical check and fails the emissions scan, which is the kind of substitution that costs a week to diagnose.
Questions we answer before a reel is booked
First, whether the topology recovers the output capacitance. In a continuous mode power factor stage or a resonant converter it does, and the 62 pF energy figure is the right one. In a hard switched flyback it does not, and the 213 pF time figure is the one that sets the loss. The same part is a good choice in the first case and a mediocre one in the second, and the question has to be answered before a price is quoted. The 62 pF energy figure belongs in a continuous mode stage and the 213 pF time figure belongs in a hard switched flyback, and quoting the wrong one changes the loss by a factor of three.
Second, how the gate is driven. With 0.8 ohm inside the package and 69 nC of total charge, an external resistor of 4.7 to 10 ohm is normal. Below that the turn on edge is fast enough to excite the drain node and the resulting ring appears in the conducted emissions scan rather than on the bench.
Third, what the avalanche rating really covers. The 820 mJ single pulse figure at 7 A is impressive and it is a single pulse figure. A converter that sees a leakage spike every cycle needs the repetitive rating, which is usually a small fraction of the single pulse number. Where a clamp has been removed to save a part, that trade should be checked against the repetitive curve rather than against the number on the first page.