Contact Us

VBM1603

Brand: VBsemi
VBsemi VBM1603 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBM1603 — Discrete & Power Semiconductors | Superb Automation

VBM1603

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBM1603 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBM1603: 210 A at 60 V in TO-220AB

The VBM1603 is an N channel MOSFET in the TO-220AB body, printed at 60 V drain to source with plus or minus 20 V on the gate. On resistance is 3 milliohm at a 10 V gate and 9 milliohm at 4.5 V, with 210 A at a 25 C case and 120 A at 125 C. The vendor calls out a halogen free body to IEC 61249-2-21 and RoHS compliance to the 2002/95 directive, and the sheet lists a 175 C junction limit with 0.4 C per watt junction to case.

The part is aimed at the same sockets as any 60 V power body: battery packs, motor drives, synchronous rectifiers and 48 V input stages where the 60 V rating covers the 57 V maximum of a telecom feed and the transient of a hot plug. What distinguishes it is the ratio of current to on resistance: 3 milliohm at 210 A is 132 W of conduction loss at the headline current, which no package can remove, so the real working point is far below the front page and the thermal path decides everything.

The ratings in one table

Drain to source voltage60 V
Gate to source voltageplus or minus 20 V
On resistance at 10 V gate3 milliohm at 30 A
On resistance at 125 C6 milliohm at 30 A
On resistance at 175 C8 milliohm at 30 A
On resistance at 4.5 V gate9 milliohm at 20 A
Continuous drain current210 A at 25 C case, 120 A at 125 C case
Continuous source current, diode120 A
Pulsed drain current, 300 microsecond480 A
Single pulse avalanche energy281 mJ into 0.1 mH, 75 A
Power dissipation375 W at 25 C case, 125 W at 125 C case
Junction to case0.4 C per watt
Gate threshold voltage2.0 V minimum, 3.5 V maximum
Total gate charge180 nC
Input capacitance9300 pF
Body diode forward voltage0.9 V at 100 A, 1.5 V maximum

What the resistance rows cost at current

The four resistance rows, 3 milliohm at 25 C, 6 at 125 C, 8 at 175 C and 9 at 4.5 V gate, are the whole economic argument for this part. Run at 100 A on a 125 C junction, the loss is 60 W in one device, which a TO-220 tab on a heatsink can remove but a board cannot. Run at 30 A, the loss is 5.4 W and the part is comfortable. The 210 A headline belongs to a cold case and a current that no practical joint sustains, and the honest continuous rating for a convection cooled product is in the tens of amps.

The 4.5 V column is a useful one because it tells the buyer that the part can be driven from a 5 V rail with 9 milliohm, three times the 10 V figure but still usable at moderate current. The threshold maximum of 3.5 V leaves enough margin for a 4.5 V drive, unlike some parts in this class where the maximum sits at or above the rail. Gate charge is 180 nC with 9300 pF of input capacitance and 750 pF of reverse transfer, and the gate resistance is 0.5 to 1.6 ohm, so the die switches fast and the external resistor is the control.

Switching times at 110 A with a 2.5 ohm gate resistor and a 0.27 ohm load are 19 ns turn on delay, 23 ns rise, 83 ns turn off delay and 35 ns fall. The turn off delay is long relative to the rise time, which is typical of a large die with high input capacitance, and it means the dead time in a synchronous stage has to be set from the measured waveform rather than from the typical numbers. The diode forward voltage of 0.9 V at 100 A is low for a body diode and keeps the dead time loss reasonable, at the cost of a recovery that the opposite switch has to absorb.

The sheet carries the same parametric verification note as others in this family, which is a statement about the data set rather than the part. For a build above a few thousand pieces we recommend a first article on each new date code, sampling resistance at 10 V, threshold and avalanche where the vendor provides a sample.

Where 60 V at 3 milliohm is used

Battery powered tools and light electric vehicles use it as the low side switch in a three phase bridge, where the 480 A pulse covers the stall and the 175 C junction allows a hot pack. Telecom and server boards use it on a 48 V input as a hot swap or a reverse polarity pass element, and the 60 V rating covers the 57 V maximum of a type 4 PoE feed. Synchronous rectifiers on a 12 V output use it where the secondary current is high and the 3 milliohm keeps the loss down, and the halogen free body matters for a product that has to meet a customer material declaration, which is a document request rather than a technical one and should be raised with the order.

Motor drives for fans and pumps use several in parallel, and at 3 milliohm the resistance dominates the threshold spread enough for reasonable sharing, provided each device has its own gate resistor and a symmetric source path. In a battery disconnect the part is usually back to back, because a single device blocks in one direction only, and the pair costs 6 milliohm plus the drive.

Buying this code and the second source

The TO-220AB is the most copied body in the industry, which makes the drawing the first thing to check and the electrical rows the second. Our power management cross reference lines up threshold maximum, resistance at 4.5 V, gate charge and avalanche energy, and for a 60 V part it adds the diode recovery, because a synchronous stage will see it. A part that matches on resistance but has a slower diode can pass a bench test and fail a thermal soak.

The supplier quality audit trail matters more for a 210 A part than for a small signal device, because the joint and the die attach are doing the thermal work. We record the date code, the lot and the on resistance sample for each shipment, and where a customer asks we hold a sample from the same lot for their own first article. The incoming inspection plan for this family also checks the tab flatness, since a warped tab is the usual cause of a void under a 200 A device.

Questions we answer on this part

Can 210 A be used at 25 C ambient? No. It is a case temperature rating, and the ambient path is 40 C per watt, so a 30 W loss in free air is already 1200 C of rise on paper, which means the real limit is set by the heatsink. The second question is whether a 4.5 V drive is safe. It is, at 9 milliohm, with a 3.5 V threshold maximum, but the gate charge is 180 nC regardless, so the driver has to deliver the same charge at the lower voltage.

The third is about paralleling. At 3 milliohm the sharing is acceptable but not automatic: threshold spread, gate resistor tolerance and source inductance all matter, and a single gate resistor shared by two devices is the usual cause of one running hot. The fourth is the diode: 120 A conduction with 0.9 V forward is good, but the recovery has to be checked in the real circuit, because a 60 V bridge at 50 kHz will see it.

On supply we quote the reel, the date code and the lot, with a resistance sample. For a halogen free declaration the customer should ask for the material certificate at the order stage, because the marking on the bag does not carry it.